• Journal of Biosystems Engineering
• /
• 제2권1호
• /
• pp.7-24
• /
• 1977

This paper is the forth and fifth one of the study on balanced type oscillating mole drainer. In the light of the results from previous reports about the model tests, some design criteria were established and a prototype machine was set up for experimental purpose. Motion characteristics and functionof the each parts of the machine were checked and analyzed. After that, performance tests of the prototype machine were carried out in thefield. Obtained results are summarized as follows ; 1. Ten centimeter of the bullet diameter was determined so as to be able to attach it to the tractors with capacity of 30 PS to 40 PS. 2. To maintain the balance between the moments of the front shank and rear shank, the oscillating amplitude of the rear bullet was determined to be larger than that of the front bullet. At the same time , the oscillating direction of the rear bullet was designed with the inclines of ten to thirty degrees. 3. An octagonal dynamo transduced was developed for measuring the compressive force of the upper link is measuring the draft force of the machine. Acceptable linear relationship between forces and strain responses from O.D.T. was obtained. 4. Analysing the balancing mechanism of the acting part of the machine , it was found that the total draft force of the machine was equal to the difference between the sum of the draft force produced from the right and left side bending moments of the lower drawber and the compressive force on the upper link. 5. There are acceptable linear relationship between the strain and twisting moment by driving shaft, and between strain and shank moment. Above results enable us to carry out the field experiment with prototype machine. 6. When the test machine was used in the field, it was possible to reduce the oscillating acceleration by forty percent in average as compared it with the single bullet mole drainer. 7. When the test machine was used under the oscillating condition, the dratt torce was reduced by 27 percent to 59 percent as compared it with the test machine under non-oscillating condition, while the draft force was increased by 7 percent to 20 percent as compared it with the mole drainer having oscillating single bullet. The reasoning behind this fact was considered as the resistance force due to the rear shank and bullet. 8. As the amplitude and frequency of the bullet were increased, the torque was increased accordingly. This tendency could be varied with the various characteristics of the given soils. And the larger frequency and amplitute, the more increasing oscil\ulcornerlating power but decreasing draft brce were needed, and draft force was increased as the velocity was increased.9. When the amplitude of the rear bullet was designed to be larger than that of the front bullet, the minimum value of the moment was lowered and oscillating acceleration was reduced. And when the oscillating direction of the rear bullet was declined back\ulcornerwards, oscillating acceleration was increased along with the increasing angle of decli\ulcornernation. When the test machine was operated in high speed, the difference between maximum moments and minimum ones became narrow. This varying magnitude of moments appeared on the moment oscillogram seems to be correlated to the oscillating acceleration and draft force. 10. From the analysis of variance, it was found that those factors such as frequency, amplitude, and operating velocity significantly affected in the oscillating acceleration, the draft resistance, the torque, the moment, and the total power required. And interaction between frequency and amplitude affected in the oscillating acceleration. 11. Within the given situation of this study, the most preferable operating conditions of the test machine were 7 Hz in oscillating frequency, 0.54 m/sec in operating velocity, and 39.1 mm in oscillating amplitude of front and rear bullets. However, it is necessary to select the proper frequency and magnitude of oscillation depending on the soil properties of the field in which the mole drainer is practiced by use of a bal1nced type oscillating mole drainer. 12. It is recommended that a comparative study of the mole drainers would be performed in the near future using two separate balanced oscillating bullet with the one which is operated by oscillating the movable bullet in a single cylinder or other balanced type which may be single oscillating bullet with spring, damper or balancing weight, and that of thing. To expand the applicability of the balanced type oscillating mole drainer in practical use, it is suggested to develop a new mechanism which perform mole drain with vinyl pipe or filling material such as rice hull.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 춘계학술대회 초록집
• /
• pp.91-91
• /
• 2011

This paper describes development procedure of the four types of fuel cell's blowers: pressurized fuel blower, selective oxidation air blower, cathode air blower, and burner air blower. Diaphragm blowers having two heads are selected to maintain force balance when the rotating arms are moving by the driving motor. Dimensions of a diaphragm cavity is designed according to the optimal design procedure using numerical simulation and experimental measurement. Experimental apparatus is designed by considering the bower characteristics having low flow rate and high pressure. Test blower is operated by a diaphragm, which has suction and discharge port on the top of the blower. For analyzing the internal flow of the blower, three-dimensional Navier-Stokes analysis is introduced in the present study. Throughout the optimal design of the blowers, blower performance is enhanced by reducing the unbalance motion of the rotating arm and loss region in the diaphragm cavity.

• Wind and Structures
• /
• 제8권3호
• /
• pp.147-161
• /
• 2005

Two identical tall building models with square cross-sections are experimentally studied in a wind tunnel with high-frequency-force-balance (HFFB) technique to investigate the interference effects on wind loads and dynamic responses of the interfered building. Another wind tunnel test, in which the interfered model is an aeroelastic one, is also carried out to further study the interference effects. The results from the two kinds of tests are compared with each other. Then the influences of turbulence in oncoming wind on dynamic interference factors are analyzed. At last the artificial neural networks method is used to deal with the experimental data and the along-wind and across-wind dynamic interference factor $IF_{dx}$ & $IF_{dy}$ contour maps are obtained, which could be used as references for wind load codes of buildings.

• 한국공간구조학회논문집
• /
• 제5권1호
• /
• pp.73-80
• /
• 2005

Serviceability of buildings is affect by excessive acceleration experienced at the top floors in wind storms that may cause discomfort to the occupants. Tuned liquid damper(TLD) and multiple tuned liquid damper(MTLD) are passive control devices that consists of rigid tank filled with liquid to suppress the vibration of structures. This TLD and MTLD are attributable to several potential advantages - low costs; easy to install in existing structures; effective even for small-amplitude vibrations. In this paper, the behavior of TLD and MTLD are investigated analytically and wind tunnel test of high-frequency force balance.

• International Journal of Fluid Machinery and Systems
• /
• 제8권4호
• /
• pp.318-326
• /
• 2015

A valve-less electro-hydraulic servo steering device (short: VSSD) for ships was chosen as a study object, and its mathematic model of hydraulic shock was established on the basis of flow properties and force balance of each component. The influence of system structure parameters, changing rate of motor speed and external load on hydraulic shock strength was simulated by the method of numerical simulation. Experiment was designed to test the hydraulic shock mathematic model of VSSD. Experiment results verified the correctness of the model, and the model provided a correct theoretical method for the calculation and control of hydraulic shock of valve-less electro-hydraulic servo steering device.

• 한국항공우주학회지
• /
• 제44권7호
• /
• pp.552-561
• /
• 2016

본 연구에서는 강제진동 기법을 이용하여 람다형상을 갖는 무미익 무인기의 동안정 미계수를 측정하였다. 강제진동 기법은 시험모델을 일정한 크기의 각 변위로 진동시키면서 항공기에 작용하는 공력의 시간이력(time history) 데이터를 측정하고, 입력진동 대비 공력데이터의 위상차와 진폭을 추출함으로써 비행체의 동안정 미계수를 계산하는 방법이다. 본 연구에서는 롤, 피치, 요 방향으로 각각 진동시킬 수 있는 실험 장치를 설계, 제작하여 국내 최초로 무미익 항공기의 동안정 미계수 측정 시험을 수행하였다. 롤 댐핑 동안정 미계수 측정 결과, 진동 주파수와 진동의 크기가 증가하여도 동안정 미계수의 경향성은 동일하게 나타나며, 전반적으로 측정 받음각 구간에서 안정한 특성을 보였다. 피치 댐핑 동안정 미계수의 경우 작은 진동 주파수에서 동적으로 더 안정해지며, 받음각 $15^{\circ}$ 이상에서는 동적으로 불안정해지는 경향성을 보였다. 각 시험데이터들은 반복성 시험을 통해 데이터의 신뢰성을 검증하였으며, 본 연구에 적용된 강제진동 기법이 무미익 항공기의 동안정 미계수를 성공적으로 측정할 수 있음을 확인하였다.

• Strategy21
• /
• 통권37호
• /
• pp.65-103
• /
• 2015

This study is an attempt to look into the future role of the ROKN and to provide a strategic way forward with a special focus on naval strategic concept and force planning. To accomplish this goal, this research takes four sequential steps for analysis: 1) assessing the role and utility of naval power of ROKN since its foundation back in 1945; 2) forecasting features of various maritime threats to influence the security of Korea in the future directly or indirectly; 3) identifying the roles to be undertaken by future ROKN; and 4) recommending Korean way of naval force planning and the operational concept of naval power. This study seeks to show that ROKN needs comprehensive role to better serve the nation with respect to national security, national prosperity and development, and future battle-space management. To safeguard the national security of Korea, it suggests three roles: 1) national guard for the peaceful unification; 2) protector of the maritime sovereignty; and 3) suppressor to maritime threats. Three more roles are highlighted for national prosperity: 1) escort of the national economy; 2) guardian for national maritime activities; and 3) contributor to the world peace. These roles need to be closely connected with the role for the battle-space management. This paper addresses the need for a dramatic shift of the central operational domain from land to maritime in the future. This will eventually offer future ROKN a leading role for developing strategic concept and force planning rather than merely a supporting one. This study finally suggests 'balanced' strategy both in concept development and force planning. A balanced force planning is a 'must' rather than an 'option' when considering a division of function between Task Fleets and Area Fleets, constructing cutting-edge conventional forces such as Aegis destroyer, CVs, or submarines, and the mix of high-profile platform and low-profile when composing future fleets. A 'balance' is also needed in operational concept. The fleet should be prepared to fulfill its missions based on two different types of force operation i.e., coercive or cooperative application of the utility of naval force. The findings and recommendations of the study are relevant today, and will be increasingly important in the future to achieve various political goals required by enhancing the utility of naval power.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.415-420
• /
• 2007

The objective of this study analyzes the influence of shimmy & shake phenomena due to tire design parameters which are RFV(radial force variation), DB(dynamic balance), RRO(radial run out) and air pressure. These parameters are inspection items for Q.C. after tires are manufactured. In order to analyze these parameters on this study, vehicle driving tests were achieved. The test modes are two type which are constant speed and coast-down driving. On this tests the dynamic characteristics of shimmy & shake are measured by the 3-axises accelerometers at the various positions that are knuckle(left & right), rack pinion, seat and steering wheel. In according to analyzed results, the longitudinal vibration of knuckle parts affects the lateral vibration of rack pinion and this vibration affects the lateral vibration of steering wheel that is the shimmy phenomena. Also the over and under DB by comparison with normal DB and the increment of RRO affect the occurrence of shimmy & shake phenomena.

• 대한물리의학회지
• /
• 제9권4호
• /
• pp.407-413
• /
• 2014

PURPOSE: We investigated the influence of heel insole and visual control on body sway index with high-heeled shoes. METHODS: The subjects of this study were 61 healthy students. None of the participants had any orthopedic or neurologic alterations. C90 area, C90 angle, trace length, sway average velocity were measured using a force plate by BT4. The variables were measured both with insole and without insole when wearing high-heeled shoes under the conditions of eyes open and eyes closed. The collected data were analyzed using the Kolmogorov-Smirnov test and paired t-test. RESULTS: When wearing high-heeled shoes with insole under the conditions of eyes open, trace length, C90 area, velocity were significantly more decreased than without insole (p<.01). When wearing high-heeled shoes with insole under the conditions of eyes closed, only C90 area was significantly more decreased than without insole (p<.05). When wearing high-heeled shoes with insole under the conditions of eyes open, trace length, C90 area, velocity were significantly more decreased than under the conditions of eyes closed (p<.01). CONCLUSION: The present study demonstrates that the use of high-heeled shoes with insole supported from heel to midfoot more increased static balance than without insole under the conditions of eyes open.

• 한국방재학회 논문집
• /
• 제8권4호
• /
• pp.47-52
• /
• 2008

Breakaway 단부장치 설계에 중요한 요소가 충돌 차량의 속도변화이다. 이는 충돌실험이나 3차원 유한요소 해석을 통해서 구할 수 있으나 에너지와 운동량 보존의 법칙을 이용하여 비교적 간단하게 계산할 수도 있다. 본 논문에서는 에너지와 운동량 보존의 법칙에 기초한 지주와 소형차 충돌 시 속도변화를 계산하는 식을 유도하였다. 이를 이용한 민감도 분석을 통하여 지주 단부의 분리하중, 파괴에너지, 차량의 강도 와 충돌속도가 소형지주에 충돌하는 차량의 속도변화에 미치는 영향을 파악하였다. 지주 단부가 기초에 고정된 정도를 나타내는 분리력 및 분리파괴에너지(Breakaway Fracture Energy)가 클수록 속도변화가 크고 충돌속도의 크기가 작을수록 속도변화가 크게 나타났다.