• 설비공학논문집
• /
• 제30권2호
• /
• pp.92-99
• /
• 2018

A numerical analysis of a compressor dehumidifier has been conducted focusing on the air side heat transfer, which is a part of a series research on the dehumidifier. The moving reference frame was applied to the fan modeling, and the porous model was used for the evaporator and condenser modeling. Curve fitting obtained the inertial and viscous resistances parameters to the results of the physical model of the unit cell with actual shape of a fin tube. The porous model was validated within a reasonable computation time for the range of practical inlet velocity of a dehumidifier. A parametric study has been conducted for fin number, fan speed (i.e., air flow rate), and evaporator/condenser tube arrangement. ANOVA analysis showed the dependency of each parameter on the velocity and temperature uniformity, which are desirable for high performance of the dehumidifier.

• 대한조선학회논문집
• /
• 제52권4호
• /
• pp.305-314
• /
• 2015

In this paper, a numerical analysis is carried out to study the drag of conical cavitators, supercavity generation devices for the high-speed underwater vehicle. The realizable k-∊ turbulence model and the Schnerr-Sauer cavitation model are applied to calculate steady-state supercavitating flows around cones of various cone angles. The calculated drags of the cones are decomposed of the pressure and the friction parts and their dependency on the geometry and the flow conditions have been analyzed. It is confirmed that the pressure drag coefficients of the cones can be estimated by a simple function of both the cone angle and the cavitation number while the friction drag coefficients approximately by well-known empirical formulas, e.g., Schults-Grunow's for the drag of the flat plate. Finally a practical method for estimating the total drags of supercavitating cones is suggested, which can be useful consequently for the design of conical cavitaors.

• 동력기계공학회지
• /
• 제12권5호
• /
• pp.48-53
• /
• 2008

Heat exchangers are commonly used in practice in a wide range of application, from heating and air-conditioning system in a household, to chemical processing and power production in a large plant. Heat transfer in a heat exchanger usually involves convection in each fluid and conduction through the wall separating the two fluids. The heat transfer characteristics of tube banks of in-line arrangements of four circular cylinders in a cross flow are compared for a range of tube locations and Reynolds numbers. The in-line pitch ratio was set up in the range of $1.5\leq L/d\leq4.0$, where L is the center to center distance and d the circular cylinder diameter, and in the Reynolds number of $13,000\leq Re\leq50,000$. The local and mean Nusselt numbers were estimated, and then. Subsequently, the heat transfer characteristics of four circular cylinders were found to exhibit a strong dependency upon the cylinder spacing and separation point of their upstream cylinders.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제4권1호
• /
• pp.45-51
• /
• 2004

We have proposed a new shallow trench isolation (STI) process using flowable oxide (F-oxide) chemical vapor deposition (CVD) for DRAM application and it was successfully developed. The combination of F-oxide CVD and HDP CVD is thought to be the superior STI gap-filling process for next generation DRAM fabrication because F-oxide not only improves STI gap-filling capability, but also the reduced local stress by F-oxide in narrow trenches leads to decrease in junction leakage and gate induced drain leakage (GIDL) current. Finally, this process increased data retention time of DRAM compared to HDP STI. However, a serious failure occurred by symphonizing its structural dependency of deposited thickness with poor resistance against HF chemicals. It could be suppressed by reducing the flow time during F-oxide deposition. It was investigated collectively in terms of device yield. In conclusion, the combination of F-oxide and HDP oxide is the very promising technology for STI gap filling process of sub-100nm DRAM technology.

• 한국전산유체공학회지
• /
• 제17권3호
• /
• pp.25-32
• /
• 2012

This work was devoted to compare two different cavitation models to study the dependency of model constants. The cavitation model of Merkle et al.(2006) and Kunz et al.(2000) were used for the present computational study. The cavitation models were coupled with the incompressible unsteady Reynolds-Averaged Navier-Stokes solver to indicate the vaporization and condensation processes. For this purpose, a preconditioning method was added as the pseudo-time term to solve the unsteady stiffness problems. For the validation of the numerical simulation, the computation was performed for the cavitating flow in a converging-diverging channel. The present results show that Merkle's cavitation model is independent to the model constants, and the higher numerical accuracy over Kunz's cavitation model.

• 한국전산유체공학회지
• /
• 제19권1호
• /
• pp.64-72
• /
• 2014

This study aimed at assessing the analysis capability of thermal-hydraulic computer code, MARS for the behaviors of the core make-up tank (CMT). The sensitivity study on the nodalization to simulate the CMT was conducted, and the MARS calculations were compared with KAIST experimental data and RELAP5/MOD3.3 calculations. The 12-node model was fixed through a nodalization study to investigate the effect of the number of nodes in the CMT (2-, 4-, 8-, 12-, 16-node). The sensitivity studies on various parameters, such as water subcooling of the CMT, steam pressure, and natural circulation flow were done. MARS calculations were reasonable in the injection time and the effects of several parameters on the CMT behaviors even though the mesh-dependency should be properly treated for reactor applications.

• 한국식품과학회지
• /
• 제29권5호
• /
• pp.932-938
• /
• 1997

Changes in viscosity and dynamic theological properties of Job's-tears were measured by Bohlin dynamic tester as a function of moisture, and measurement was performed within a linear viscoelastic range. The result of the shear stress vs shear rate of Job's-tears at different moisture contents $(50{\sim}75%)$ was applied to mathematical models and Herschel-Bulkley model showed the highest correlation coefficient. Lower moisture content (55%) produced higher yield stress and consistency index, but lower flow behavior index, whereas higher moisture content showed reverse effects. Job's-tears with $50{\sim}70%$ moisture contents showed a higher storage modulus (G') than loss modulus (G') at all frequencies, showing a higher concentrated polymer characteristics. However, higher moisture content (>75%) showed crossover point between G' and G', and frequency dependency. As the moisture content was increased, the amount of viscoelastic properties such as G', G', complex viscosity decreased during heating, and initial temperature and miximum value of viscoelastic properties shifted to higher temperatures, representing the moisture-dependence of Job's-tears upon theological properties.

• 설비공학논문집
• /
• 제23권11호
• /
• pp.754-761
• /
• 2011

The present study numerically investigates two-dimensional flow and heat transfer in the multiple confined impinging slot jet. Numerical simulations are performed for the different Reynolds numbers(Re=100 and 200) in the range of nozzles from 1 to 9 and height ratios(H/D) from 2 to 5, where H/D is the ratio of the channel height to the slot width. The vector plots of velocity profile, stagnation and averaged Nusselt number distributions are presented in this paper. The dependency of thermal fields on the Reynolds number, nozzle number and height ratio can be clarified by observing the Nusselt number as heat transfer characteristic at the stagnation point and impingement surface. The Nusselt number at the stagnation point of the central slot shows unsteadiness at H/D=3 and Re=200. The value of Nusselt number at the stagnation point of the central slot decreases with higher Reynolds number and number of nozzle although overall area averaged Nusselt number increases. Hence careful selection of geometrical parameters and number of nozzle are necessary for optimization of the heat transfer performance of multiple slot impinging jet.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.187-187
• /
• 2007

This paper presents the electrical properties of SiGe HBTs designed with bottom collector and single metal layer structure for RF power amplifier. Base layer was formed with graded-SiGe/Si structures and the collector place to the bottom of the device. Bottom collector and single metal layer structures could significantly simplify the fabrication process. We studied about the influence of SiGe base thickness, number of emitter fingers and temperature dependence (< $200^{\circ}C$) on electrical properties. The feasible application in 1~2GHz frequency from measured data $BV_{CEO}$ ~10V, $f_r$~14 GHz, ${\beta\simeq}110$, NF~1 dB using packaged SiGe HBTs. We will discuss the temperature dependent current flow through the e-b, b-c junctions to understand stability and performance of the device.

• 한국소음진동공학회논문집
• /
• 제18권1호
• /
• pp.110-122
• /
• 2008

Pneumatic vibration isolator typically consisting of dual-chamber pneumatic springs and a rigid table are widely employed for proper operation of precision instruments such as optical devices or nano-scale equipments owing to their low stiffness- and high damping-characteristics. As environmental vibration regulations for precision instruments become more stringent, it is required to improve further the isolation performance. In order to facilitate their design optimization or active control, a more accurate mathematical model or complex stiffness is needed. Experimental results we obtained rigorously for a dual-chamber pneumatic spring exhibit significantly amplitude dependent behavior, which cannot be described by linear models in earlier researches. In this paper, an improvement for the complex stiffness model is presented by taking two major considerations. One is to consider the amplitude dependent complex stiffness of diaphragm necessarily employed for prevention of air leakage. The other is to employ a nonlinear model for the air flow in capillary tube connecting the two pneumatic chambers. The proposed amplitude-dependent complex stiffness model which reflects dependency on both frequency and excitation amplitude is shown to be very valid by comparison with the experimental measurements. Such an accurate nonlinear model for the dual-chamber pneumatic springs would contribute to more effective design or control of vibration isolation systems.