• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.6
• /
• pp.507-511
• /
• 2006

We investigated accelerated soft error rate (ASER) in static random access memory (SRAM) cells of thin film transistor (TFT) type. The effects on ASER by cell density, buried nwell structure, operational voltage, and polysilicon-2 layer thickness were examined. The increase in the operational voltage, and the decrease in the density of SRAM cells, respectively, resulted in the decrease of ASER values. The SRAM chips with buried nwell showed lower ASER than those with normal well structure did. The ASER decreased as the test distance from alpha source to the sample increased from $7{\mu}m\;to\;15{\mu}m$. As the polysilicon-2 thickness increased up to $1000\;{\AA}$, the ASER decreased exponentially. In conclusion, the best condition for low soft error rate, which is essential to obtain highly reliable SRAM device, is to apply the buried nwell structure scheme and to fabricate thin film transistors with the thick polysilicon-2 layer

• Journal of Surface Science and Engineering
• /
• v.37 no.6
• /
• pp.319-325
• /
• 2004

Fe thin films containing Si particles were prepared on metallic substrates by electrodeposition method in sulfate solutions and the content of codeposited Si particles in the films was investigated as a function of applied current density, the content of Si particels in the solution, solution pH, solution temperature and concentration of $FeSO_4$$7H_2$O in the solution. The amount of Si codeposited in the film was not dependent on the applied current density, solution pH and solution temperature, while it was dependent on the content of Si particles in the solution and the concentration of $FeSO_4$$7H_2$O in the solution. The amount of Si codeposited in the film increased with increasing content of Si particles in the solution but reached a maximum value of about 6 wt% when the content of Si particles in the solution exceeds 100 g/l. On the other hand, the content of Si codeposited in the film increased up to about 17 wt% with decreasing concentration of $FeSO_4$$7H_2$O in the solution. These results would be applied to the fabrication of very thin Fe-6.5 wt% Si sheets for electrical applications.

• Korean Journal of Metals and Materials
• /
• v.47 no.5
• /
• pp.316-321
• /
• 2009

Co nanoparticles on silica substrates were fabricated by inducing a thin-film dewetting through two different processes-furnace annealing and pulsed-laser annealing. The effects of annealing temperature, film thickness and laser energy density on dewetting morphology and mechanism were investigated. Co thinfilms with thicknesses between 3 to 15 nm were deposited using ion-beam sputtering, and then, in order to induce dewetting, thermally annealed in furnace at temperatures between 600 and $900^{\circ}C$. Some as-deposited films were irradiated using a Nd-YAG pulsed-laser of 266 nm wavelength to induce dewetting in liquid-state. Films annealed in furnace agglomerated to form nanoparticles above $700^{\circ}C$, and those average particle size and spacing were increased with an increase of film thickness. On the laser annealing process, above the energy density of $100mJ/cm^2$, metal films were completely dewetted and the agglomerated particles exhibited greater size uniformity than those on the furnace annealing process. A detailed dewetting mechanism underlaying both processes were discussed.

• Elastomers and Composites
• /
• v.57 no.4
• /
• pp.157-164
• /
• 2022

Representative bulletproof materials, such as aramid or ultra-high molecular weight polyethylene(UHMWPE), have excellent strength and modulus in the plane direction but are very vulnerable to forces applied in the thickness direction. This paper reports a study on the effects of reinforcement in the thickness direction when bulletproof composite fabrics are prepared to improve their performance. Aramid and UHMWPE fabrics were combined using the film-bonding, needle-punching, or stitching methods and then subjected to low-velocity projectile and ball-drop impact tests. The results of the low-velocity projectile test indicated that the backface signature(BFS) decreased by up to 29.2% in fabrics obtained via the film-bonding method. However, the weight of the film-bonded fabric increased by approximately 23% compared with that obtained by simple lamination, and the fabric stiffened on account of the binder. Flexibility, light weight for wearability, and excellent bulletproof performance are very important factors in the development of bulletproof materials. When the needle-punching method was used, the BFS increased as the fibers sustained damage by the needle. When the composite fabrics were combined by stitching, no significant difference in weight and thickness was observed, and the BFS showed similar results. When a diagonal stitching pattern was employed, the BFS decreased as the stitching density increased. By contrast, when a diamond stitching pattern was used, the fabric fibers were damaged and the BFS increased as the stitching density increased.

• Korean Journal of Soil Science and Fertilizer
• /
• v.32 no.2
• /
• pp.203-209
• /
• 1999

This study was conducted to obtain the basic data on agricultural use of arbuscular mycorrhizal fungi(AMF) in salt accumulated plastic film house soil by evaluating the density of AMF spores in plastic film house in Yeong Nam area and surface sterility condition, germination rate of AMF spores, and hyphal growth in vitro. The density of AMF spores in plastic film house soils was highest in the site of water melon, and those of cucumber, melon, hot pepper sites were followed in order. The number of AMF was in the range of 101-207 per 100 g dry soil. With decreasing the ratio of bacteria to fungi(B/F), the population density of AMF was increased, and available $P_2O_5$ content of soil was significantly correlated to the population densities of AMF($r=0.416^*$). The surface sterility rate and spore germination of AMF isolated in plastic film house soil were more than 50% in 2% chloramin T and 2% chloramin T + antibiotic and 0.5% NaOCl treatments. The germination rate of Gigaspora margarita in the range of initial pH 5~9 of the medium was more than 56%. Hyphal growth was increased as pH of the medium increased. However the germination rate of Acaulospora spinosa was highest in the medium of pH 9, and hyphal growth in vitro was poor and not related to pH of the medium.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.329-329
• /
• 2007

Photoconductive poly crystalline lead oxide coated on amorphous thin film transistor (TFT) arrays is the best candidate for direct digital x-ray detector for medical imaging. Thicker films with lessening density often show lower x-ray induced charge generation and collection becomes less efficient. In this work, we present a new methodology used for the high density deposition of PbO. We investigate the structural properties of the films using X-ray diffraction and electron microscopy experiments. The film coatings of approximately $200\;{\mu}m$ thickness were deposited on $2"{\times}2"$ conductive-coated glass substrates for measurements of dark current and x-ray sensitivity. The lead oxide (PbO) films of $200\;{\mu}m$ thickness were deposited on glass substrates using a wet coating process in room temperature. The influence of post-deposition annealing on the characteristics of the lead oxide films was investigated in detail. X-ray diffraction and scanning electron microscopy, and atomic force microscopy have been employed to obtain information on the morphology and crystallization of the films. Also we measured dark current, x-ray sensitivity and linearity for investigation of the electrical characteristics of films. It was found that the annealing conditions strongly affect the electrical properties of the films. The x-ray induced output charges of films annealed in oxygen gas increases dramatically with increasing annealing temperatures up to $500^{\circ}C$ but then drops for higher temperature anneals. Consequently, the more we increase the annealing temperatures, the better density and film quality of the lead oxide. Analysis of this data suggests that incorporation and decomposition reactions of oxygen can be controlled to change the detection properties of the lead oxide film significantly. Post-deposition thermal annealing is also used for densely film. The PbO films that are grown by new methodology exhibit good morphology of high density structure and provide less than $10\;pA/mm^2$ dark currents as they show saturation in gain (at approximate fields of $4\;V/{\mu}m$). The ability to operate at low voltage gives adequate dark currents for most applications and allows voltage electronics designs.

• Progress in Superconductivity and Cryogenics
• /
• v.6 no.3
• /
• pp.16-20
• /
• 2004

YB $a_2$C $u_3$$O_{7-x}$ (YBCO) films were deposited on (100) SrTi $O_3$ single crystal substrates by a metal organic chemical vapor deposition (MOCVD) system of hot-wall type using single liquid source. Under the condition of the mole ratio of Y(tmhd)$_3$:Ba(tmhd)$_2$:Cu(tmhd)$_2$= 1:2.1:2.9. the deposition pressure of 10 Torr. the MO source line speed of 15 cm/min. the Ar/ $O_2$ flow rate of 800/800 sccm. YBCO films were prepared at the deposition temperatures of 780∼89$0^{\circ}C$. In case of the YBCO films with 2.2 ${\mu}{\textrm}{m}$ thickness deposited for 6 minutes at 86$0^{\circ}C$. XRD pattern showed complete c-axis growth and SEM morphology showed dense and crack-free surface. The atomic ratios of Ba/Y and Cu/Ba in the film were 1.92 and 1.56. respectively. The deposition rate of the film was as high as 0.37 ${\mu}{\textrm}{m}$/min. The critical temperature ( $T_{c.zero}$) of the film was 87K. The critical current of the film was 104 A/cm-width. and the critical current density was 0.47 MA/$\textrm{cm}^2$. For the thinner film of 1.3 ${\mu}{\textrm}{m}$ thickness. the critical current density of 0.62 MA/$\textrm{cm}^2$ was obtained.d.

• Journal of Powder Materials
• /
• v.23 no.5
• /
• pp.379-383
• /
• 2016

A thick film of $Li_7La_3Zr_2O_{12}$ (LLZO) solid-state electrolyte is fabricated using the tape casting process and is compared to a bulk specimen in terms of the density, microstructure, and ion conductivity. The final thickness of LLZO film after sintering is $240{\mu}m$ which is stacked up with four sheets of LLZO green films including polymeric binders. The relative density of the LLZO film is 83%, which is almost the same as that of the bulk specimen. The ion conductivity of a LLZO thick film is $2.81{\times}10^{-4}S/cm$, which is also similar to that of the bulk specimen, $2.54{\times}10^{-4}S/cm$. However, the microstructure shows a large difference in the grain size between the thick film and the bulk specimen. Although the grain boundary area is different between the thick film and the bulk specimen, the fact that both the ion conductivities are very similar means that no secondary phase exists at the grain boundary, which is thought to originate from nonstoichiometry or contamination.

• Journal of Bio-Environment Control
• /
• v.6 no.4
• /
• pp.292-298
• /
• 1997

These studies were conducted to verify the effect of the supplementary lighting by reflective film mulching and its establishment in the north side of greenhouse on the utility of light at tomato by means of investigating changes of leaf temperatures, stomatal features, transpiration rates and photosynthetic rates. Stomatal density of leaves were high in the reflective film mulching but sizes of stomata were not different. As the osmotic potential in rooting zone was low, the stomatal resistance was high, transpiration rate was low, and leaf temperature was increased by 40.62$^{\circ}C$. And also in the block of reflective film mulching photosynthetic rates were decreased hut chlorophyll contents were not different. Especially, there is an effect of controlling greenhouse whiteflies by treatment of reflective film mulching. It is thought that the reason of high quality or increasing yield at several crops by supplementary lighting, such as reflective film mulching, would be caused by influences of absorption and distribution of nutrients through high transpiration rate and photosynthesis which resulted from increase of stomata.

• Polymer(Korea)
• /
• v.27 no.2
• /
• pp.98-105
• /
• 2003

The surface energy and the effect of functional groups on the surface of the ozone-treated low-density polyethylene (LDPE) film were studied. Treatment conditions were treatment time, total amount of transferred ozone, and ozone concentration. The introduction of polar groups on the surface of LDPE film after ozone treatment was confirmed by FTIR-ATR and XPS analyses. Surface fee energy of the LDPE film was examined by a contact angle method. The ozone treated-LDPE film showed a decreased water contact angles about 15$^{\circ}$ mainly due to the increased concentration of oxygen-containing functional groups, which was attributed to the increased surface free energy or $O_{IS}/C_{IS}$Also, the concentrations of the oxygen-containing functional groups on the surface of LDPE film increased with ozone treatment time and concentration, whereas no significant effects were found for the total amount of transferred ozone. From the dyeability test using Kubelka-Munk equation, it was found that the ozone treatment plays an important role in the growth of oxygen-containing functional groups of LDPE film, resulting in the improvement of dyeability for basic dyeing agent.