• Journal of the Korean Wood Science and Technology
• /
• v.3 no.1
• /
• pp.3-15
• /
• 1975

How to stabilize wood against shrinking and swelling in variable atmospheric moisture conditions is important to the wood-using industry and a challenge to research. Polyethylene glycol stabilize wood by bulking the fiber. PEG also serve as a chemical seasoning agent, suppress decay in high concentrations, and have slight effect on physical properties, gluing or finishing. The study designed to determine the effect of PEG-400 on the dimensional stabilization of local hardwoods for wood carvings that could supply a greatly expanding tourist trade and making curved furniture parts, lamp stands and other decorative objects, and possible gunstock. The species examined were 6 species, Seo-Namoo (Carpinus laxiflora), Cheungcheung-Namoo (Cornus controversa), Gorosae-Namoo (Acer mono), Karae-Namoo (Juglans mandshurica), Jolcham-Namoo (Quercusserrata) and Sanbud-Namoo (Prunus sargentii), used as block of 5cm thick radially to the grain, 7cm wide tangentially, and 70cm long parallel to the wood grain. All these test piecies were conditioned above the fiber saturation point before impregnation. The stabilization effects were determined for PEG-400 treated woods in a 50 percent solution for 20 days. The following conclusions were obtained. PEG retentions increased with treating time. It was more effective to treat at 60$^{\circ}C$ than at room temperature. In degree of PEG-400 impregnation on species, Cheungcheung-Namoo havinglow specific gravity had the highest retentions, 68.77% but the lowest, 56.33% was shown in Jolcham-Namoo with high specific gravity. Specific gravity of treated wood increased considerably with effectiveness of polymer loading. The increases in specific gravity were 5.36 to 13.16 percent. The highest was Jolcham-Namoo, the lowest Karae-Namoo. On the dimensional stability, a 40 percent of effectiveness of polymer loading was just as effective as 60 percent in reduction in water absorptivity (RWA), antishrinkage efficiency (ASE) and antiswelling efficiency (AE), and from over 60 percent they increased more rapidly. Also species response varied considerably. ASE was 30.12 to 69.97 percent tangentially and 27.86 to 56.37 percent radially, AE 34.06 to 73.76 percent tangentially and 30.11 to 70.12 percent radially, and RWA 42.31 to 65.32 percent. No differences in volume swelling among the 6 species were observed. Its values were ranged from 14.98 to 19.55 percent and also increased with PEG retentions. On the mechanical properties, the strengths very much decreased with PEG-400 loadings as shown in Figure 12; that were 11.41 to 22.90 percent in compression, 21.61 to 34.35 percent in bending and 22.83 to 36.83 percent in tensile strength. PEG retention in cell wall was less than 1 percent and the most of PEG were immersed in cell lumen. Except for Korae-Namoo, effectivenesses of polymer loading were as much high as 61.58 to 75.02 percent. This is believed to be due to the effect of PEG-400 on excellant dimensional stability of treated woods.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.6
• /
• pp.869-877
• /
• 2020

The power consumption in the low consistency (LC) refining is an important indicator for the optimal control of the process and it is composed of the net power and the no-load power. The refining efficiency and process characterization of LC refining are directly affected by power consumption. In this paper, the effect of pulp consistency and average fiber length on the power consumption and refining efficiency were studied through the LC refining trials conducted by an experimental disc refiner. It is found that the curve of power-gap clearance can be divided into constant power section, power reduction section, and power increase section. And the no-load power and the adjustable domain of loading applied by the refining plates will increase as the increase of pulp consistency, while the increase of net power is larger than that of no-load power which makes the increasing of refining efficiency. Meanwhile, the adjustable domain of loading applied by the refining plates can be slightly improved by increasing the average fiber length, but its effect on the no-load power in the LC refining process can be neglected. The study of power consumption in LC refining is of positive significance for the proper selection of pulp properties in LC refining, in-depth exploration of refining mechanism, and energy consumption reduction in refining.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.42 no.2
• /
• pp.67-74
• /
• 2010

This study was carried out to investigate the pulping and papermaking characteristics of lotus (Nelumbo nucifera G.) leafstalk for the development of high performance paper. Anatomical and chemical properties of the lotus leafstalk were analyzed. The pulping and papermaking properties of the lotus leafstalk by conventional alkali and sulfomethylated pulping processes were also evaluated. The length and width of fibers were 0.06-3.32 mm (av. 1.23 mm) and 3.47-25.6 ${\mu}m$ (av. 20.7 ${\mu}m$), respectively. The length and width of vessel elements were 0.07-0.78 mm (av. 0.20 mm) and 14.1-330.0 ${\mu}m$ (av. 54.13 ${\mu}m$), respectively. The fiber length/fiber width ratio was 60.20. The extractives (cold water, hot water, 1% NaOH and ethanol-benzene) and lignin content of lotus leafstalk were higher than those of plant bast fiber. The contents of holocellulose, lignin, and ash were 73.8%, 24.3%, and 4.3%, respectively. The pulp yields based on pulping methods were sulfomethylated pulping av. 52%, and alkaline pulping av. 42%. The conventional alkaline pulping shows better pulp and sheet properties than the sulfomethylated pulping which was modified pulping processes. But the sulfomethylated pulping shows higher brightness than alkali pulping. In the consequence of FE-SEM observation, lotus leafstalk pulp consists of various kinds of thin walled fibers which have large amount of small pits.

• Journal of the Korean Wood Science and Technology
• /
• v.15 no.2
• /
• pp.99-104
• /
• 1987

Fiber mats were made at various density levels, using fibers from papermill sludge, ricestraw and various mixtures of the two. The paper mill sludges were collected from Moorim Papermill Co, and Jeonjoo Papermill Co. They were soaked in the liquid sulfur compounds, sulfur-tall oil and sulfurpolyester compounds, and made into fiber-reinforced, sulfur-based composition board. Under optimum conditions of fiber mat preparation and saturation with molten sulfur and modified sulfur, the Young's moduls of the manufactured tiber-reinforced composition board are superior to those of conventional wood-based composition boards. For example, the moduli of elasticity of the composition board made from papermill sludge, with a density of 0.40gm/$cm^3$, were greater than 1,400,000psi as compared 800,000psi for high density hardboard(1.28gm/$cm^3$). The modulus of rupture of the best reinforced composition board manufactured was over 9000psi, comparable to 6000psi of high density hardboard. The proposed Bryant and Lee's theory, "Modified Rule of Mixtures" can be applicable to the nonoriented and short fibrous composition board, when it was modified from "Rule of Mixtures" established by Paul an Jones, and supplemented by Smith and Cox's theory, In the Bryant and Lee's theory of $E_c=\frac{1}{3}aE_fV_f+bE_mV_m$, the constants "a" and "b" for the composition boards made from papermill sludge and the mixtures of ricestraw and the sludge were identified to be in the ranges of 3.29~3.54 and -2.47~-2.80 respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.52 no.3
• /
• pp.205-220
• /
• 2024

Various polylactic acid (PLA) blends were reinforced with untreated or silane-treated micro-sized cellulose fiber (MCF), successfully prepared as 3D printing filaments and then printed using a fused filament fabrication (FFF) 3D printer. In this study, we focused on developing 3D-printed MCF/PLA composites through silane treatment of MCF and investigating the effect of silane treatment on the various properties of FFF 3D-printed composites. Fourier transform infrared spectra confirmed the increase in hydrophobic properties of silane-treated MCF by showing the new absorption peaks at 1,100 cm^-1, 1,030 cm^-1, and 815 cm^-1 representing C-NH₂, Si-O-Si, and Si-CH₂ bonds, respectively. In scanning electron microscope images of silane-treated MCF filled PLA composites, the improved interfacial adhesion between MCF and PLA matrix was observed. The mechanical properties of the 3D-printed MCF/PLA composites with silane-treated MCF were improved compared to those of the 3D-printed MCF/PLA composites with untreated MCF. In particular, the highest tensile and flexural modulus values were observed for S-MCF10 (5,784.77 MPa) and S-MCF5 (2,441.67 MPa), respectively. The thermal stability of silane-treated MCF was enhanced by delaying the initial thermal decomposition temperature compared to untreated MCF. The thermal decomposition temperature difference at T₉₅ was around 26℃. This study suggests that the effect of silane treatment on the 3D-printed MCF/PLA composites is effective and promising.

• Journal of Korean Society of Forest Science
• /
• v.81 no.4
• /
• pp.357-362
• /
• 1992

To understand water flow path in the cells of Robinia pseudoacacia and Pyrus ussuriensis and obtain color wood from them, this experiment was performed by penetrating 0.5% acidic fuchsin and 0.5% fast green solution into the living wood of them. A comparison was made of the wood structure and water flow path from Robinia pseudoacacia containing the ring-porous wood with tyloses, and Pyrus ussuriensis including solitary diffuse-porous wood with distinct fiber pits. The dye penetrated into vessel elements in the early wood of two growth rings from bark in Robinia pseudoacacia, but permeated all xylem in fonts ussuriensis. In Robinia pseudoacacia, the vessels of heart wood and intermediate wood were not stained because of tyloses.

• Journal of the Korean Wood Science and Technology
• /
• v.10 no.3
• /
• pp.168-179
• /
• 1982

The first step to utilize the growing resources of Italian poplar (Populus euramericana I-476) for pulp-Woods, its characteristics and adaptabilities to the pulp industry must be investigated completely. The plantation methods are important for its fast growing in stock, and no less important is the cutting age for its utilization as pulpwood. In this paper, the stone groundwood pulping, refiner groundwood pulping and chemi-groundwood pulping characteristics by the age of tree, along with their physical and chemical characterstics were tested, and relationships between the age groups were analyzed to find out the optimum felling age. The results obtained are as follows: 1. The coefficient of pliability was a little higher in the case of younger trees. 2. The water retention value of each pulp was directly proportional to its physical strength, but this tendency was not detected between the age groups of sample woods. 3. Generally, the physical strength of younger wood pulp was lower regardless of the pulping process. But in the case of pretreatment with NaOH, Asphund and CGP pulp from 5 year old sample wood were stronger in physical strengths than those of GP and Asplund pulp with no pretreatment from 10 years old sample wood. 4. The tear factor of Asplund pulp with alkali pretreatment was higher than that of CGP pulp but the breaking length and the burst factor was similar in all processes. Considering the pulp yield and its brightness, CGP process seems to be advantageous. 5. The dissimilarity of physical strength between 7 and 10 years old wood pulp was not very large in all pulping processes but the physical strength of 5 year old wood pulp was very weak. In the of groundwood pulping from Italian poplar woods, 5 year old wood pulp should be mixed with other long fiber pulp for making a good paper.

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.2
• /
• pp.108-116
• /
• 2010

This paper explains the effects of wood drying on treatability (as determined by water uptake) of Japanese red pine (Pinus densiflora S. et Z.) at the sevenmoisture content (MC) levels above and below the fiber saturation point (FSP). According to the experimental results, it was found that water uptake (as the percentage of void volume filledwith distilled water, VVF%) was influenced by level of moisture content and percentage of void volume filled was improved effectively by kiln drying process. A significant relationship between moisture content and treatability was established. Permeability and liquid uptake were decreased above the FSP due to the effect of the less void space available in wood. Even though increased liquid uptake was observed at lower moisture content, no significant differences was observed moisture content below 20%. Therefore, this species need to be initially dried below FSP before treated with liquids. But drying moisture content below 10% might not be economical for the commercial purpose comparing drying the wood between 10 and 20% moisture content. The result of this study inferred that the treatability of pine wood can be improved by reducing the moisture content up to a certain level of 10~20% for allowing better performance.

• Journal of agriculture & life science
• /
• v.46 no.2
• /
• pp.9-17
• /
• 2012

In this study, in addition to the green tea - wood fiber hybrid composite boards of previous researches, to make effective use of saw dust of domestic cypress tree with functionalities and application as interior materials, eco-friendly hybrid composite boards were manufactured from wood fiber, green tea and saw dust of cypress tree. We investigated the effect of the component ratio of saw dust and green tea on dynamic MOE (modulus of elasticity). Dynamic MOE was within 1.41~1.65 GPa, and showed the highest value in wood fiber : green tea : saw dust = 50 : 40 : 10 of the component ratio, and had the lowest value in 50 : 30 : 20 of component ratio. These values were 1.4~1.6 times higher than static bending MOE of wood fiber - saw dust - green tea hybrid composite boards, and were 2.0~2.9 times lower than those of green tea - wood fiber hybrid composite boards reported in the previous researches. From the results of correlation regression analyses between dynamic MOE and static strength performances, a very high correlation coefficients were obtained, therefore it was found that static bending strength performances can be estimated with a high reliability from dynamic MOE.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.1
• /
• pp.40-47
• /
• 2016

Instead of metal connector generally used on the structural glued laminated timber rahmen joints, the GFRP reinforced laminated plates combining veneer and GFRP (Glass Fiber Reinforced Plastic) and bonded type GFRP rod were used as the connectors. As a result of moment resistance performance evaluation on the joint part applied with these connectors, the yield moment of specimen using the GFRP reinforced laminated plates and GFRP rod pin was measured 4 % lower in comparison to the specimen (Type-1) using the metal connectors, but the initial rotational stiffness was measured 29% higher. Also, the yield moment and rotational stiffness of the specimen using the GFRP-reinforced laminated plates and wood (Eucalyptus marginata) pin showed were measured 11% and 56% higher in comparison to the Type-1 specimen, showing the best performance. It was also confirmed through the failure shape and perfect elasto-plasticity analysis that it showed ductility behavior, not brittle fracture, from the shear resisting force by the pin and the bonding strength increased and the unification of member was carried out. On the other hand, in case of the specimen bonded with GFRP rod, it was impossible to measure the bonding performance or it was measured very low due to poor bonding.