• Clean Technology
• /
• v.5 no.2
• /
• pp.53-61
• /
• 1999

Presented is the design method of the waste heat recovery facility for the flue gas produced from combustion and incineration processes of large industrial environmental waste treatment and cogeneration plants. The present study assumes the basic design concept of wast heat recovery facility as the combination of waste heat recovery boiler and steam power cycle, and then describes the modeling technique, the design concept and criteria of each component of waste heat recovery facility. In addition, the present study investigates how the thermal performance of waste heat recovery facility varies with boiler operating pressure and waste heat recovery heat exchanger design at the same flue gas condition.

• Nuclear Engineering and Technology
• /
• v.32 no.3
• /
• pp.274-282
• /
• 2000

The simulation of water balance was conducted for suggested four alternative multi-layer cover design of near-surface radioactive waste disposal facility under domestic climate condition. The analysis was also conducted for the most favorable one out of four alternative cover design under conservative scenarios. Until 100 years after closure of disposal vault, the infiltration flux for the most favorable cover design was negligible even under doubling of the ambient precipitation condition. When the degradation of asphalt and geomembrane after 100 years of closure was considered, the infiltration flux significantly increased almost to the design criteria of cover system in I' Aube disposal facility. And it was found that the hydraulic conductivity of bentonite/sand as a bottom barrier should be no greater than 1$\times$10$^{-7}$ cm/sec recommended by U.S. EPA.

• Journal of The Korea Institute of Healthcare Architecture
• /
• v.10 no.2
• /
• pp.107-115
• /
• 2004

In this paper, the all units of residential housing that is not legislated in facility development law are analyzed and foreign design criteria that is related to barrier-free unit housing is comparing to domestic. Through the comparison in front door, living room, bathroom, bedroom, and kitchen, this paper aims to suggest internal barrier-free design criteria. This paper is limited to internal housing which are front door, living room, bedroom, bathroom, and kitchen. Also, the objectives of facility development law are U.S, Japan, German, and in case of U.S, UFAS is established by ADA, in Japan, Heart Building law and detail standard drawing are used, in German, DIN is used. The objective of domestic case study is the latest residential housings that are built over 2003. The flow of study is as follows ; First, the internal items of residential housing are abstracted, and each item is checked in facility development law that is legislated in. Next, through comparison of domestic and foreign facility development law related to housing, common items are abstracted and detail standards are defined. Domestic residential housings are analyzed in those standards. Finally, the problems that is the result of analysis are analyzed and the barrier free design criteria is abstracted in unit housing. Also, more developed items and future study are suggested.

• Journal of The Korea Institute of Healthcare Architecture
• /
• v.5 no.8
• /
• pp.55-62
• /
• 1999

Recently the facility requirements and regulations of healthcare facilities for the aged were changed, but the justification of requirements have not been identified. The facility requirements are so important to plan and design the facility. So this paper aims to identify the problems, and to compare & analyse the facility requirements.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1136-1141
• /
• 2008

The helicopter rotor system generates lift, thrust, maneuvering force and moment to the helicopter with the torque and pitch control force transferred from the main rotor hub/control. And the tail rotor system generates the thrust for yaw axis control of the helicopter with the torque and pitch control force transferred from the tail rotor hub/control. Ground whirl test shall be performed to verify the compliance of requirement performance test and dynamic test of rotor blade and hub/control. This paper describes a design of whirl tower test facility for helicopter rotor system test and evaluation. Design results are summarized and compared with design requirements.

• Journal of Korean Society for Quality Management
• /
• v.19 no.1
• /
• pp.151-162
• /
• 1991

The purpose of this study is to propose a facility layout design algorithm based on artificial intelligence concept, and then to develop a computer program which is more practical than any other conventional facility layout design systems. The algorithm is composed of five step layout procedures; knowledge and data input, knowledge interpretation, priority determination, inference of layout design, and evaluation, In the step of priority determination, the algorithm is divided into single row and multi row layout problem. In the step of inference of layout design, alternatives are generated by constraints-directed reasoning and depth first search method based on artificial intelligence concept. Alternatives are evaluated by the moving cost and relationship value by interactive man-machine interface in the step of evaluation. As a case study, analytical considerations over conventional programs such as CRAFT and CORELAP was investigated and compared with algorithm propsed in this study. The proposed algorithm in this study will give useful practical tool for layout planner. The computer progran was written in C language for IBM PC-AT.

• International Journal of Reliability and Applications
• /
• v.2 no.4
• /
• pp.269-280
• /
• 2001

The objective of this paper is to provide a model for effective implementation of costing RAM management in the design and procurement of production facility considering the system cost-performance trade-off. This research proposes a two-step approach of costing RAM design and test of system RAM for production facility. In Step 1, a static model is proposed to find an initial system configuration to meet the required performance based on system RAM and LCC and analyzes the trade-off relationships between various factors of RAM and LCC. In the second Step, we developed time and failure truncated models for system reliability test and analysis. For the computational purpose, we developed computer programs and have shown the sample results. By the sample test run, the proposed model has shown the possibilities to provide a good method to analyze system performance evaluation for both design and operational phase, This model can be applied to a wide variety of systems not only for costing RAM of the production facilities but also for the other kinds of equipment.

• Journal of the Korean Home Economics Association
• /
• v.40 no.9
• /
• pp.191-205
• /
• 2002

The purpose of this study is to identify the homelike design characteristics of elderly housing facility. To investigate what the preference of physical design characteristics are, interview was done by unstructured questionnaire to 30 middle aged and middle income group housewives living in Seoul. It was identified that preferred homelike physical characteristics of the houses were composed of 4 themes, housing types, building appearences and garden, floor plan and natural and social environments of its location. Their desirable housing standard was amenity which is the highest level of home environment. In their later life, they wanted to live in vicinity of Seoul to enjoy cultural benefits of the city and active outdoor activities in sunny, natural suburban environment. They liked a spacious, clean and bright color with natural material furnishings. Each architectural design expression of 4 themes was suggested.

• Journal of the Korean Institute of Educational Facilities
• /
• v.22 no.1
• /
• pp.3-12
• /
• 2015

The user participatory design process collects users' opinions efficiently through a feedback process such as various user workshops and conferences. When users who actually participated in a design process use the facility in which they were a participant, their satisfaction with the design quality of the facility they use may be enhanced; therefore, user participatory design methods in school construction are deemed to enlarge consistently the interest in a school of students, parents, teachers, and local residents. This paper selected the most appropriate user participatory design methods through an analysis of actually applied cases, and applied them to the empirical exploration process. Also, problems incurred through the empirical exploration process were solved by various user participatory design methods based on actually experienced cases and the results of workshops performed. As such, this paper deduced problems by applying user participatory design methods in practice, and solved problems by executing the empirical exploration process again. Through this, the paper proposed a variety of user participatory design methods for improving school design and raising user satisfaction.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.835-840
• /
• 2011

The development of a turbopump is fundamental to have an independent LRE(liquid rocket engine) for KSLV-II. Recently, the detail design of a turbopump real-propellant test facility based on liquid oxygen and kerosene has been performed to structure the test facility for the experimental validation of the turbopump. In this paper, the design requirements of the turbopump and the specifications of the test facility was presented and the representative sub-facilities were explained on the basis of the design results. Also, the uncertainty of the sub-facilities which could be appeared during the operation was removed in advance through the simulation method and the experimental verification.