• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.10
• /
• pp.763-766
• /
• 2010

By improving the conducting process of metal source/drain (S/D) in direct contact with the channel, schottky barrier metal-oxide-semiconductor field effect transistors (SB MOSFETs) reveal low extrinsic parasitic resistances, offer easy processing and allow for well-defined device geometries down to the smallest dimensions. In this work, we investigated the arrhenius plots of the SB MOSFETs with different S/D schottky barrier (SB) heights between simulated and experimental current-voltage characteristics. We fabricated SB MOSFETs using difference S/D metals such as Cr (${\Phi}_{Cr}$ ~4.5 eV) and Ni (${\Phi}_{Ni}$~5.2 eV), respectively. Schottky barrier height (${\Phi}_B$) of the fabricated devices were measured to be 0.25~0.31 eV (Cr-S/D device) and 0.16~0.18 eV (Ni-S/D device), respectively in the temperature range of 300 K and 475 K. The experimental results have been compared with 2-dimensional simulations, which allowed bandgap diagram analysis.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.12 s.177
• /
• pp.34-41
• /
• 2005

There is a strong demand fur the contactless transportation device fur a hard disk and silicon wafer without contaminating and damaging them. To fulfill this requirements, A transportation device fur them has been proposed. But the device needs many of costly displacement sensors positioned along the transportation interval and possesses a very complicated controller and driving scheme. To overcome those kinds of drawback, in this paper, we present a very simple and cost-effective transportation device which only consists of a linear guide, very simple electrostatic suspension system and driving circuit of stepping motor. The principle of stable suspension by relay feedback control, derivation of lateral restoring force, the design of transportation system are described, fellowed by the experimental system. Experimental results show that a 3.5-inch hard disk has been transported with a speed of approximately 20mm/s while being suspended stably at a gap of 0.25mm.

• 대한공업교육학회지
• /
• v.32 no.1
• /
• pp.117-133
• /
• 2007

The purpose of this study was to develop the force measuring device of learning wind tunnel, teaching-learning materials in order to enhance understanding of flight principle and give interest about aviation technology in secondary school. The content of this study was consisted of the development and experiment of force measuring device for learning wind tunnel. The main results of this study were as follows: This device developed here is simple structure applying lever principle instead of the comparatively expensive load cell used in engineering college or a aviation research institute and so on. Measurement of lift and drag as well as the comparison experiment of a fluid resistance is possible with only one device developed here. The lift coefficient with angle of attack has shown the same tendency in both of theoretical and experimental values. And the stall phenomenon was found under the larger angle of attack of experimental rather than expected theoretical values. The drag coefficient with angle of attack has shown the same tendency in both of theoretical and experimental values. And drag coefficient the rate of increasement of the experimental values increased more gently than its theoretical values.

• Electrical & Electronic Materials
• /
• v.9 no.8
• /
• pp.799-805
• /
• 1996

In short channel MOSFET, it is very important to establish optimal process conditions because of variation of device characteristics due to the process parameters. In this paper, we used process simulator and device characteristics caused by process parameter variation. From this simulation, it has been ' derived to the dependence relations between process parameters and device characteristics. The experimental result of fabricated short channel device according to the optimal process parameters demonstrate good device characteristics.

• Smart Structures and Systems
• /
• v.26 no.5
• /
• pp.605-617
• /
• 2020

In this study, the experimental tests for the direct tensile strength measurement of Ultra-High Performance Concrete (UHPC) were numerically modeled by using the discrete element method (circle type element) and Finite Element Method (FEM). The experimental tests used for the laboratory tensile strength measurement is the Compressive-to-Tensile Load Conversion (CTLC) device. In this paper, the failure process including the cracks initiation, propagation and coalescence studied and then the direct tensile strength of the UHPC specimens measured by the novel apparatus i.e., CTLC device. For this purpose, the UHPC member (each containing a central hole) prepared, and situated in the CTLC device which in turn placed in the universal testing machine. The direct tensile strength of the member is measured due to the direct tensile stress which is applied to this specimen by the CTLC device. This novel device transferring the applied compressive load to that of the tensile during the testing process. The UHPC beam specimen of size 150 × 60 × 190 mm and internal hole of 75 × 60 mm was used in this study. The rate of the applied compressive load to CTLC device through the universal testing machine was 0.02 MPa/s. The direct tensile strength of UHPC was found using a new formula based on the present analyses. The numerical simulation given in this study gives the tensile strength and failure behavior of the UHPC very close to those obtained experimentally by the CTLC device implemented in the universal testing machine. The percent variation between experimental results and numerical results was found as nearly 2%. PFC2D simulations of the direct tensile strength measuring specimen and ABAQUS simulation of the tested CTLC specimens both demonstrate the validity and capability of the proposed testing procedure for the direct tensile strength measurement of UHPC specimens.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.16 no.12
• /
• pp.1101-1106
• /
• 2004

Magnetic refrigeration is based on the magnetocaloric effect (MCE)-the ability of some materials to heat up when magnetized and cool down when demagnetized. A rotary magnetic refrigeration device using gadolinium (Gd) ribbon and permanent magnets was constructed for experimental study. Gd ribbon attached around a rotating wheel is cyclically magnetized and demagnetized by permanent magnets and exchanges heat with liquid in the surrounding container. Temperature of the liquid in each divided section of the container was measured and the experimental results obtained in this study were discussed.

• International Journal of Advanced Culture Technology
• /
• v.7 no.4
• /
• pp.229-235
• /
• 2019

Due to the development of video and optical technology today, video equipments are being used in a variety of fields such as identification, security maintenance, and factory automation systems that generate products. In this paper, we investigate an algorithm that effectively recognizes an experimental object in an input image with a partial problem due to the mechanical problem of the input imaging device. The object recognition algorithm proposed in this paper moves and rotates the vertices constituting the outline of the experimental object to the positions of the respective vertices constituting the outline of the DB model. Then, the discordance values between the moved and rotated experimental object and the corresponding DB model are calculated, and the minimum discordance value is selected. This minimum value is the final discordance value between the experimental object and the corresponding DB model, and the DB model with the minimum discordance value is selected as the recognition result for the experimental object. The proposed object recognition method obtains satisfactory recognition results using only partial information of the experimental object.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2327-2332
• /
• 2007

This study investigates on the inhalation force improvements of hood consisted one of the local ventilation systems attached the new device named as gas-guidance-device for removed a pollution source. The numerical method applying finite element method is calculated the velocity and pressure distributions of a moving fluid at the beginning and the inside of a hood with and without the gas-guidance-device in hood. And, the experimental study is measured the wind velocity using the anemometer at the same condition of numerical study. Also, the optimum shape of gas-guidance-device which is suitable for hood shape derived from the numerical and experimental results. The results of this study is supplied the important data to an industrial field for control of a pollution source in the engineering aspect. Moreover, the introduced technique of hood attached the gas-guidance-device is very useful to remove the harmful materials such as dust and waste happened in the manufacturing factory.

• Steel and Composite Structures
• /
• v.46 no.2
• /
• pp.237-252
• /
• 2023

The article describes the development of a novel dissipative bracing connection device (identified by the acronym DRBrC) for concentrically braced frames in steel and composite structures. The origins of the device trace back to the seminal work of Kelly, Skinner and Heine (1972), and, more directly related, to the PIN-INERD device, overcoming some of its limitations and greatly improving the replaceability characteristics. The connection device is composed of a rigid housing, connected to both the brace and the beam-column connection (or just the column), in which the axial force transfer is achieved by four-point bending of a dissipative pin. The experimental validation stages, presented in detail, consisted of a preliminary testing campaign, resulting in successive improvements of the original device design, followed by a systematic parametric testing campaign. That final campaign was devised to study the influence of the constituent materials (S235 and Stainless Steel, for the pin, and S355 and High Strength Steel, for the housing), of the geometry (four-point bending intermediate spans) and of the loading history (constant amplitude or increasing cyclic alternate). The main conclusions point to the most promising DRBrC device configurations, also presenting some suggestions in terms of the replaceability requirements.

• Journal of International Academy of Physical Therapy Research
• /
• v.3 no.2
• /
• pp.458-463
• /
• 2012

This study is to examine the effects of a feedback breathing device exercise and diaphragm breathing exercise on pulmonary functions of chronic strokes patients. The selection of 20 subjects was divided equally and placed into a experiment group and a control group and the intervention was applied four times per a week for five weeks. In each session, both groups received rehabilitative exercise treatment for 30 minutes, and a feedback breathing device exercise for 15 minutes. In addition, experimental group conducted a combination of diaphragm breathing exercise for 15 minutes. Prior to and after the experiment, patients' pulmonary functions were measured using a spirometer. The pulmonary function tests included FVC, FEV1, FEV1/FVC, PEF, VC, TV, IC, ERV, IRV. With respect to changes in the pulmonary functions of both groups, the experimental group significantly differed in FVC, FEV1, TV, ERV but did not in PEF, FEV1/FVC, VC, IRV. The control group did not significantly differ in any of the tests. There were significant differences in FEV1, FEV1/FVC, TV, ERV between the two groups, but no significant differences in FVC, PEF, FEV1/FVC, VC, IRV between them after the experiment. The experimental group, which conducted a combination of a feedback breathing device exercise and diaphragm breathing exercise, saw their respiratory ability increase more significantly than the control group. The breathing exercise was found to improve pulmonary function in chronic stroke patients.