• Journal of Advanced Marine Engineering and Technology
• /
• 제11권3호
• /
• pp.31-44
• /
• 1987

Nowadays, the problems of energy and environmental pollution become serious day by day and the diesel engine, which has been proved to be superior to gasoline engine with respect to fuel consumption and ecological problems of exhaust gas, has been adopted widely for various purposes from the marine diesel engine and the dynamo engine to all kinds of engine on land. Therefore, extensive parametric studies on combustion of diesel engine should be done for its desing and improvement. To predict the behavior of diesel engien according to variable operating conditions by means of cycle simulation, the reasonable pattern of heat release rate has to be asumed. But it is necessary to know the actual variation of heat release rate in order to assume the reasonable pattern of heat release rate according to the actual operating conditions. In this paper, on a high speed small bore diesel engine with pre-combustion chamber, experimental investigations were carried out to determine the relationship between the heat release pattern and parameters such as engine load and speed. And also, the theoretical investigations about the performance variations of the above diesel engine according to the predicted pattern of heat release rate variation were performed. From the above observations, it may be said that the Fanboro indicator, which was used to get the cylinder pressure, can be used to estimate a reasonable pattern of heat release rate and it is confirmed that the pattern of heat release rate for the pre-combustion type engine is different from that of the direct injection type engine.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 전기학술대회논문집
• /
• pp.154-159
• /
• 2005

In proportion to the increase of industrial development, emission troubles were concerned as global issue. For these reasons, so many researchers and associated institutes effort to reduce pollution with new technology and various devices. As a kind of these methods, we used catalysts as a after-treatment system. At first, we made equipment of model furnace. And various catalysts were equipped at exhaust duct of combustion system, and excess air ratio( ), change cell numbers, catalyst materials(Pt, Pd) were changed as experimental conditions. With these various condition, temperature, NOx, CO, HC, $CO_2$ and $O_2$ concentration were measured. As a result, NOx conversion were increased with increasing of cell number in Pd catalyst. And Pt catalyst were became 100% conversion at 200 and 300 cell. Also, Pt catalyst was better than Pd catalyst ${\alpha}$=1.5 in this condition. In addition, CO and HC concentrations were decreased${\alpha}$=1.5 with Pd catalyst.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.277-282
• /
• 2006

Road traffic noise is not produced by any one factor rather occurs as a composition of various factors. Its occurrence is made by running engine noise, tire frictional, and exhaust noise etc. The quality of the noise depends on the size of the vehicles, rotation and engine speed, vehicle load, package state of the road and incline etc. The occurrence of noise level of heavy trucks appears louder than smaller vehicles and the noise levels produced differs according to speed and load etc between similar size vehicles. Other factors such as traffic density, average speed, mixing rate of heavy vehicles, and the distance between vehicles also generate road traffic noise. In this paper we examine 2, 4, and 6-lane roads in Jeonju. Consequently, this study examined the means used to measure road traffic noise. It was found that when there is a large traffic density and the average velocity is below 70 km/hr, the noise level could receive a relative proper value by the current measuring means. But in the case of night-time, it was found that the current measuring method is inapposite.

• 한국자동차공학회논문집
• /
• 제8권5호
• /
• pp.1-11
• /
• 2000

This study is aimed to develop a proto-type LPG engine for medium-duty commercial vehicles in order to substitute for conventional diesel engine. Recently, it is recognized that diesel engines are main cause for smoke pollution in urban site. So, it is expected to reduce this environmental emission by developing and substituting LPG engine which has the advantage of practical use in a short development period in aspects of infrastructures. For that, after analysing the specifications and performance characteristics of a base diesel engine, parts of combustion chamber, intake system, fuel supply and ignition systems suitable for LPG combustion were re-designed and manufactured. And and engine controller for fuel supply and ignition distributions was matched by feedback mapping based on the speed-load conditions. The torque and power of LPG engine were increased by 6∼12% on the overall driving conditions compared to the base diesel engine, and fuel consumption rate marked the similar level based on the fuel price. Exhaust emissions such as THC, CO, NOx recorded the same order with conventional LPG engine for passenger car.

• 한국자동차공학회논문집
• /
• 제19권5호
• /
• pp.7-13
• /
• 2011

The climate change due to the increased consumption with fossil fuel and rise of the oil price have been serious global issues. Automobile industry consumes 30% of the oil every year and causes air pollution and global warming by the exhaust emissions and carbon dioxide ($CO_2$). The demand of two-wheeled vehicle increases every year due to the parking and traffic problem caused by the increased automobiles in the urban area. Approximately 50,000,000 two-wheeled vehicles were produced in 2008. The development and sales of the hybrid two-wheeled vehicle industry become active due to its increased market demands. In this paper, the change of the motor and battery efficiency, driving distance, hill climbing ability with the change of the motor capacity was analyzed. Simulation of the peculiarities in urban driving schedule(World-wide Motorcycle Test Cycle(WMTC), Manhattan driving schedule), constant speed(10 km/h, 35 km/h) of small electronic two-wheeled vehicle was also carried out. Through the simulation result, appropriate capacities of the motor and battery for urban driving was acquired.

• 에너지공학
• /
• 제23권2호
• /
• pp.57-61
• /
• 2014

자동차산업이 해결해야 할 과제로서 석유에너지의 소비증가와, $CO_2$ 배출에의한 지구온난화, 배기가스 배출에 의한 도시부 대기오염 등에 대한 대처가 필요한 시점이다. 이들의 해법으로 시장에서 높은 평가를 받고 있는 전기자동차의 필요성이 대두되고 있다. 본 연구에서는 전기자동차 모터, 배터 리 및 구동모터를 포함한 고전압 핵심부품들의 효율적인 열관리 기술, 배터리 및 구동모터의 열관리 기술 및 개발동향을 알아보고자 한다.

• 한국소음진동공학회논문집
• /
• 제17권3호
• /
• pp.274-281
• /
• 2007

Road traffic noise is not produced by any one factor rather it occurs as a composition of various factors. Its occurrence is made by running engine noise, tire frictional, and exhaust noise etc. The quality of the noise depends on the size of the vehicles, rotation and engine speed, vehicle load, package state of the road and incline etc. The occurrence of any noise level of heavy trucks appears louder than smaller vehicles and the noise levels produced differs according to speed and load etc between similar size vehicles. Other factors such as traffic density, average speed, mixing rate of heavy vehicles, and the distance between vehicles also generate road traffic noise. In this paper we examine 2, 4, and 6-lane roads in Jeonju. Consequently, this study examines the means used to measure road traffic noise. It was found that when there is a large traffic density and the average velocity is below 70 km/h, the noise level could receive a relative proper value by the current measuring means. But in the case of night-time, it was found that the current measuring method is inapposite.

• 자원리싸이클링
• /
• 제5권2호
• /
• pp.45-51
• /
• 1996

국내산 무연탄의 경우 약 0.3∼7% 정도의 황을 포함하고 있어 연소시 대기오염은 물론 산성비의 원인이 되는 SOx 및 NOx 등을 배출한다. 환경오염 문제에 대처하기 위한 화력발전소의 SOx 방출 허용기준치는 우리나라의 경우 1995년 500ppm이지만 1999년에는 270ppm으로 강화될 전망이다. 본 연구에서는 고구배 자선기를 이용하여 습식 자력선탄과 오일 응집에 의한 탈황의 가능성을 조사하였다. 자력선별법에서는 입도의 크기, matrix 종류, 광액의 농도, 급광속도, 정선횟수 그리고 탄종변화 등을 실험한 결과 최적 실험조건에서 강릉지역산 시료의 석탄회수율은 82.1%, 황분제거율은 60.8%이었다. 오일 응집 시험에서는 pH변화, 응집제의 종류 및 첨가량, 광액의 농도, 정산 그리고 탄화도 등에 관하여 실험한 결과 마로산시료의 석탄회수율 98.0%이었으며, 회 및 황의 제거율은 각각 70.9%와 95.7%이었다.

• 한국재료학회지
• /
• 제29권9호
• /
• pp.525-531
• /
• 2019

The widespread use of automobiles has greatly increased energy demand and exhaust gas pollution. In order to save energy, reduce emissions and protect the environment, making lightweights automobiles is an effective measure. In this paper, carbon fiber composites and automobile B-pillars are briefly introduced, and then the mechanical properties and impact resistance of the DC590 steel B-pillars and carbon fiber composites B-pillars are simulated by the ABAQUS finite element software. The results show that the quality of compound B-pillars is reduced by 50.76 % under the same dimensions, and the mechanical property of unit mass is significantly better than that of metal B-pillars. In the course of a collision, the kinetic energy of the two B-pillars is converted into internal energy, but the total energy remains the same; the converted internal energy of the composite B-pillars is greater, the deformation is smaller and the maximum intrusion and intrusion speed is also smaller, indicating that the anti-collision performance of the composite B-pillars is excellent. In summary, the carbon fiber composites can not only reduce the quality of the B-pillars, but also improve their anti-collision performance.

• Journal of the Korean Wood Science and Technology
• /
• 제47권3호
• /
• pp.277-289
• /
• 2019

Herein, a case study discussing the effect of carbonaceous aerosol pollution, which is emitted during the charcoal kiln manufacturing processes or carbonization processes, on the atmospheric environment is presented . In South Korea, in situ analysis of different charcoal production plants specialized in the production of charcoal sauna indicate that the emitted organic carbon (OC) and elemental carbon (EC) aerosols are significantly influenced by the nature of the biomass and technological processes, i.e., treatment or emissions abatement systems for the exhaust effluent gases. In detail, total carbon (TC), which is calculated as the sum of OC and EC emission factors, varied widely from a charcoal production site to another ranging from 21.8 to 35.8 gTC/kg-oak, where the mean value for the considered production sites was approximately 28 gTC/kg-oak (N = 7 and sum = 196.4). Results indicate that the emission factors from a modern charcoal production process in South Korea are quantitatively lower in comparison with the traditional kiln. This study aims to propose advanced wood processes for the production of charcoal from the viewpoint of environmental protection policy and green engineering.