• Journal of the Korea Organic Resources Recycling Association
• /
• v.13 no.2
• /
• pp.74-84
• /
• 2005

The objectives of this study was to investigate the improvement of thermal kinetics for disposal of sewage sludge using thermal wind drying. The operational parameters varied are the temperature of $130{\sim}170^{\circ}C$ and evaporation velocity WD. Important parameters effect on thermal kinetics for evaporation of water in sewage sludge studied include the drying time, water content of sewage sludge, solids amount of sewage sludge(TS%) by the varied temperature. The saturation point of water evaporation was observed at the drying time of 60 min in conditions of drying temperature $170^{\circ}C$ and drying time of 120 min by drying temperature $130^{\circ}C$ and WD=0.95 m/s. Operation at drying temperature of $170^{\circ}C$ led to higher rate of evaporation than those 130, $150^{\circ}C$ at WD=1.0 m/s and WD=1.0 m/s was higher than WD=0.5 m/s at drying temperature of $130^{\circ}C$.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1997.10a
• /
• pp.51-58
• /
• 1997

An experimental study was performed to discover the tribological behaviors of pure tin and zinc coated 52100 bearing steel. Pure tin coatings ranging from 30 nm to 30,000 nm and pure zinc coatings ranging from 500 nm to 52,000 nm were produced by a thermal evaporation coating method. Experiments using a thrust ball bearing-typed rolling test-rig were performed for the investigations of the effect of coating thickness on the tribological rolling behavior. Results showed that the existence of optimum film thickness which revealed minimum rolling resistance was discovered for tin and zinc coating. The compatibility of coating matehal to iron showed no significant effect on the rolling resistance behavior. The hardness of coating material revealed significant influence to the rolling resistance behavior.

• Archives of Pharmacal Research
• /
• v.23 no.4
• /
• pp.385-390
• /
• 2000

To demonstrate the effect of formulation conditions on the controlled release of protein from poly(lactide-co-glycolide) (PLGA) microspheres for use as a parenteral drug carrier, ovalbumin (OVA) microspheres were prepared using the W/O/W multiple emulsion solvent evaporation and extraction method. Methylene chloride or ethyl acetate was applied as an organic phase and poly(vinyl alcohol) as a secondary emulsion stabilizer. Low loading efficiencies of less than 20％ were observed and the in vitro release of OVA showed a burst effect in all batches of different microspheres, followed by a gradual release over the next 6 weeks. Formulation processes affected the size and morphology, drug content, and the controlled release of OVA from PLGA microspheres.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.688-691
• /
• 1999

Light was of electric lamp was reflected by bulb reflector. In order to improve the efficiency of the electric lamp. it is inevitable that lamp, it is inevitable that improve the reflectance of bulb reflector. Important factors that affect the reflectance of bulb reflector is working pressure, distance between evaporation source to substrate, the situation of surface of glass. etch rate of glass, etc. In this paper. confirmed the effect of etching, working pressure etc. , and its effect for the reflectance of bulb reflector. Especially, concentration of HF in the etching solution and etching time is to be importnace for characteristic of bulb reflector.

• Journal of the Korean Ceramic Society
• /
• v.37 no.8
• /
• pp.799-804
• /
• 2000

Coulometric titration experiments have been done for copper doped cobaltous oxide (Co1-xCux)1-$\delta$ O with various dopant concentrations. We present the obtained experimental data and compare our results to those of previous thermogravimetric investigation. The experimental data are fitted by theoretical calculations based on various defect models. For this modeling, we considered different types fo major defects like copper in substitutional and interstitial lattice sites as well as copper vacancy. We also introduced the copper evaporation effect during titration experiment into our consideration.

• Proceedings of the Korean Magnestics Society Conference
• /
• 1996.10a
• /
• pp.32-33
• /
• 1996

• Journal of Power System Engineering
• /
• v.17 no.6
• /
• pp.102-107
• /
• 2013

In this paper, the performance analysis for evaporation capacity, total work and efficiency of the ocean thermal energy conversion(OTEC) power system using mixed refrigerant(R32,R152a) is conducted to find the effect of hot wasted water on OTEC power system. The system in this study is applied with two stage turbine, regenerator, cooler and separator on Organic Rankine Cycle. The commercial program HYSYS is used for the performance analysis. The main results were summarized as follows : The efficiency of the OTEC power cycle has a largely effect on the evaporation capacity and total work. As increasing temperature of heat source water, evaporator's capacity is decreased but total work increase. Otherwise, using hot wasted water bring effects not only increasing system efficiency but also declining evaporator's capacity. Thus With a thorough grasp of these effect, it is necessary to find way to use hot wasted water emitted by power plant and so on.

• Journal of the Korean Vacuum Society
• /
• v.12 no.2
• /
• pp.112-117
• /
• 2003

MgO films is widely used in plasma display panel (PDP) technology. In this work, structural and optical properties of the MgO films deposited by e-beam evaporation, reactive magnetron sputtering, which are commercially used, and arc deposition were compared. MgO thin films were deposited on glass substrates by vacuum arc deposition equipment using a magnesium metal target at various oxygen gas flows. In order to investigate the packing density by ellipsometer, to measure reasonable erosion-rates of the MgO protective layers, we introduced an acceleration test method, namely, Ar+ ion beam induced erosion test. Also, XPS and UV test were adopted to examine the effect of the moisture on the optical transmittance of the MgO protective layers, which showed that these of MgO films by arc deposition method sustained more 90% and were insensitive to effect of the moisture. XRD and AFM have been also used to study behaviors of the structure and surface morphology.

• Restorative Dentistry and Endodontics
• /
• v.35 no.5
• /
• pp.321-334
• /
• 2010

Objectives: The purpose of this study is to evaluate bonding efficacy by means of measuring the effect of remained solvent on Degree of conversion(DC) and ${\mu}TBS$ and FE-SEM examination. Materials and Methods: Two 2-step total etching adhesives and two single-step self etching adhesives were used in this study. First, volume weight loss of 4 dentin adhesives were measured using weighting machine in process of time in normal conditions and calculate degree of evaporation (DE). Reaction/reference intensity ratio were measured using micro-Raman spectroscopy and calculate DC according to DE. Then 2 experimental groups were prepared according to air-drying methods (under, over) and control group was prepared to manufacturer's instruction. Total 12 groups were evaluated by means of micro tensile bond strength and FE-SEM examination. Results: Degree of evaporation (DE) was increased as time elapsed but different features were observed according to the kind of solvents. Acetone based adhesive showed higher DE than ethanol and butanol based adhesive. Degree of conversion (DC) was increased according to DE except for $S^3$ bond. In ${\mu}TBS$ evaluation, bond strength was increased by additional air-drying. Large gaps and droplets were observed in acetone based adhesives by FE-SEM pictures. Conclusions: Additional air-drying is recommended for single-step self etching adhesive but careful consideration is required for 2-step total etching adhesive because of oxygen inhibition layer. Evaporation method is carefully chose and applied according to the solvent type.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.565-568
• /
• 2006

This study was retentive material into the porosities of the permeable asphalt concrete, we developed retentive asphalt concrete which can absorb water in rain and decrease the temperature of the pavement through the vaporization of rainwater. The experimental results showed that the maximum stability appeared in the 5.0% types of both AP-5 and SBS PMA. Between these two types, the maximum stability of the asphalt with AP-5 was 480kg, which means it met the stability requirement for walkways but didn't meet the requirement for roadways. On the other hand, the maximum stability of the asphalt concrete with SBS PMA was 676kg, which was 176 kg higher than the requirement for roadways(500kg) and satisfy the requirement of KS. The retentive material was 56.4% in the type of the retentive material with 30% diatomaceous earth, 66.6% in 50% type, 87.5% in 70% type. In the aspect of thermal properties, the retentive asphalt concrete can lower the surface temperature by about 15 degrees lower than the normal asphalt concrete can. This effect could be made by the evaporation cooling effect and the surface albedo. It should be noted that the evaporation cooling effect cools it by about 10 degrees and the surface albedo by about 5 degrees.