• 한국기계가공학회지
• /
• 제19권2호
• /
• pp.47-54
• /
• 2020

Themo-mechanical analysis was carried out using the finite element method for the steel shell of a cupola furnace. When the outer surface of the shell was cooled with water to within the temperature range of 35-80 ℃ during operation of the cupola, the inner surface of the shell was expected to exhibit a temperature of 65-248 ℃ based on heat transfer analysis. The shell was also expected to have an equivalent stress range of 100-280 MPa in the outer surface over the temperature range examined. Upon cooling the shell to obtain an outer surface temperature <80 ℃, the maximum equivalent stress of the shell did not exceed the yield strength. Although the temperature of the outer surface varied between 35 and 80 ℃ periodically due to the cooling control problem, the fatigue stress at the outer surface of the shell was calculated to be within the fatigue strength. During a non-operational period to examine the system between furnace operations, the thermal stress presented in the shell was sufficiently low to reach the desired yield strength and fatigue limit.

• 한국기계가공학회지
• /
• 제11권6호
• /
• pp.1-8
• /
• 2012

This study investigates stress and deformation due to static and dynamic vibration analysis about various types of bike handles installed with smart phone depositories. When force is applied on the side of handle at the models of type 1, 2, 3 and 4, the maximum equivalent stress is highest at type 2. The stress or deformation becomes lowest among these 4 model types. At vibration analysis, type 1 becomes safest within the range of 500Hz and type 3 becomes stable within the range of 100Hz. The result of this study can be applied with the design of bike handle installed with smart phone depository. The damage or deformation due to vibration can be prevented when the bike falls down. This result can be widely utilized to investigate and predict the durability.

• 국제강구조저널
• /
• 제18권4호
• /
• pp.1242-1251
• /
• 2018

Not all loads contribute to fatigue crack propagation in the welded detail of steel bridges when they are subjected to variable amplitude loading. For fatigue assessment, therefore, non-contributing stress cycles should be truncated. However, stress range truncation is not considered during typical fatigue reliability assessment. When applying the first order reliability method, stress range truncation occurs mismatch between the expected number of cycles to failure and the number of cycles obtained at the time of evaluation, because the expected number of cycles only counts the stress cycles that contribute to fatigue crack growth. Herein, we introduce a calibration factor to coordinate the expected number of cycles to failure to the equivalent value which includes both contributing and non-contributing stress cycles. The effectiveness of stress range truncation and the proposed calibration factor was validated via case studies.

• 한국강구조학회 논문집
• /
• 제9권3호통권32호
• /
• pp.363-375
• /
• 1997

절취된 세로보를 갖는 강철도교량의 바닥판에서의 피로거동 및 손상시 보수 보강의 효과를 연구하기 위해 8개 대형시험체에 대한 모형시험을 수행하였다. 실교량을 대상으로 실동응력을 측정하여 기본 응력범위 빈도히스토그램을 작성하고 이에 의한 변동응력의 등가응력범위를 산출하였다. 이 등가응력범위를 기준으로 피로시험의 응력변동범위의 크기를 조정하면서 정적 및 피로시험을 보강전과 보수 보강후로 구분하여 실시하였다. 정적시험에 의하면 재하하중의 크기가 등가실동응력 수준인 시험체의 경우에서 이미 허용응력과 비슷한 응력을 나타내므로서 피로균열의 발생조건을 충족하고 있었다. 손상된 시험체에 대해 다양한 보수 및 보강을 실시하여, 각각의 결과를 비교검토하였다. 그 결과 보수효과는 stop hole을 천공하고 고장력볼트를 체결한 경우에 피로균열성장의 지체효과가 뚜렷하게 나타났다. 한편 보강효과는 휨의 지배를 받는 세로보의 경우 인장측 플랜지의 보강이 효과적이며, 복부의 보강은 보강방법으로 적절하지 않음을 알 수 있었다. 또한 직각절취된 세로보의 피로설계등급은 우리나라 시방서 피로설계규정의 E등급에 해당한다는 것을 확인할 수 있었다.

• 예술인문사회 융합 멀티미디어 논문지
• /
• 제7권3호
• /
• pp.411-419
• /
• 2017

기하학적으로 급격히 변화되는 부분의 응력집중은 봉에 작용하는 평균응력 보다 큰 응력이 작용하여, 봉의 파손을 발생시키는 원인 중 하나이다. 구멍과 단이 있는 봉이 비틀림 하중을 받았을 경우, 응력집중 변화에 대해 구멍의 위치에 따른 관계를 규명하였다. 본 논문에서는 범용 유한요소 소프트웨어인 ANSYS Workbench를 통해 구멍의 위치가 다른 봉의 응력을 해석하였다. 해석된 결과, 필렛과 구멍이 서로 가까울수록 응력이 증가되는 것으로 나타났다. 또한, 본 해석에 사용된 모델에서는 구멍이 필렛으로부터 특정거리(L : -100 mm ~ 300 mm) 이상에서는 구멍과 필렛에서 발생한 최대 등가응력이 거의 일정하였다. 반면에, 구멍이 필렛으로부터 특정거리(L : -100 mm ~ 300 mm) 이하에서는 구멍과 필렛에서 발생한 최대 등가응력이 급격하게 증가 및 감소하는 변화를 보였다. 그리고 특정거리(L : -100 mm ~ 300 mm) 이하에서 구멍과 필렛에서 발생한 등가응력의 차이가 발생하는 지점을 확인할 수 있었다. 본 논문의 해석 결과는 비틀림을 받는 단이 있는 봉에서 구멍 위치를 선정할 때, 사용 될 수 있다.

• 한국강구조학회 논문집
• /
• 제8권4호통권29호
• /
• pp.19-29
• /
• 1996

In this paper, it is presumed that the stress time history was generated by simulation method and investigated compatibility in regard to the reappearance of stress time history. In this procedure, the identified frequency distribution of stress range of the steel railroad bridge varies with the rational values of cut off point and bar width. Thus, we show variable aspect of the equivalent stress range results from change of cut off point and bar width. In addition, we analyze the variable of RMC and RMS model due to the cut off point and bar width of the measured stress history which influencs the prediction of fatigue life in the steel railroad bridge. The simulated stress time history is carried out by the superposition method incorporating the vertical load with rotation moment obtained from the Hermition interpolation function, and compared with developing stress results from measured maxi mum stress. Through this study, we can estimate the remaining fatigue life from a safety point of view and comparative accuracy.

• 한국자동차공학회논문집
• /
• 제21권6호
• /
• pp.166-174
• /
• 2013

This study investigates the strength durability on the results of structural and vibration analysis due to the shape of excavator wheel. As model 2 has the least stress by comparing three models with maximum equivalent stress, model 2 has most durability among three models at static analysis. Maximum equivalent stress is shown at the bottom part contacted with ground and this part on wheel is most affected by load in cases of all models. Safety factor can be decided with the value of 2.3 by considering the yield stress of this model. The range of maximum harmonic response frequencies becomes 6900 to 7000Hz. As model 2 has the least total deformation and equivalent stress at these critical frequencies, model 2 has the most durability at vibration analysis among three models. The structural and vibration analysis results in this study can be effectively utilized with the design of excavator wheel by investigating prevention and durability against its damage.

• International Journal of Safety
• /
• 제9권1호
• /
• pp.12-20
• /
• 2010

In this study, a series of random field test and dynamic analysis in the time domain were carried out in order to find in the reason of fatigue damage of the main and the secondary members in the 3-span continuous steel plate girder railway bridge being under in service over 60 years. From the measured and the analyzed results, the stress distribution patterns were investigated for the members with fatigue damage. In addition, global and local numerical stress analysis was performed for the members damaged severely by corrosion, to estimate variation of the distribution by corrosion. Finally, a reasonable cut-off ratio in the steel plate railway bridge will be proposed by analyzing the equivalent stress ranges according the ratio.

• Structural Engineering and Mechanics
• /
• 제21권6호
• /
• pp.737-765
• /
• 2005

This paper presents a theoretical model for the behavior of partially confined axi-symmetric reinforced concrete members subjected to axial load. The analysis uses the theories of elasticity and plasticity to cover the full range of the concrete behavior. Analysis of the elastic range of the problem involves boundary conditions that are defined along a relatively simple geometry. However, extending the analysis into the plastic range involves difficulties that arise from the irregular geometry of the boundary between the plastic zone and the elastic zone, a boundary which is also changing as the axial load increases. The solution is derived by replacing the discrete steel ties with an equivalent tube of thickness $t_{eq}$ and by analyzing the concrete cylinder, which is uniformly confined by the equivalent tube. The equivalency criterion initiates from a theoretical analysis of the problem in its elastic range where further finite element analysis shows that this criterion is valid also for the plastic range of the cylinder material. According to the proposed model, the efficiency of the lateral reinforcement can be evaluated by the equivalent thickness $t_{eq}$. Comparison with published test results of confined reinforced concrete stress-strain curves shows good agreement between the test and the analytical results.

• 산업기술연구
• /
• 제18권
• /
• pp.187-193
• /
• 1998

In this study, about the fatigue life of welded structure material under fluctuation loading, the prediction life which is produced by using the Histogram Recorder System was compared with the experimental life which is produced by the RMC model which is imported by conception of equivalent stress. In this result, this is represented few difference by comparing prediction life which is produced by damage analysis depended on Miner's rule, by using the Histogram Recorder System, with experimental life which is produced by the RMC load model which is imported by conception of equivalent of stress, therefore fatigue life is easily predicted by using Histogram Recorder System, and result of prediction has equivalent accuracy with other method which is more complex than the Histogram Recorder System. Besides the damage which is produced by stress which is high thirty percentage rank in the stress range of damage inducing, is nearly equal to the damage which is induced the rest of seventy percentage, there fore we can see that damage accumulation which is induced few time overload which is effected welded structure material is great.