• Applied Chemistry for Engineering
• /
• v.23 no.2
• /
• pp.153-156
• /
• 2012

In this study, two different methods were studied to prepare Pt-Pd catalysts for direct methanol fuel cells in order to enhance the electrochemical efficiency. The catalysts were compared with simultaneously deposited Pt-Pd and sequentially deposited Pt-Pd. The electrocatalysts contained 20 wt% of metal loading on carbon black and 1 : 2 of Pt : Pd atomic ratio. Electrochemical properties of the catalysts were compared by measuring cyclic voltammetries and average sizes and lattice parameters were measured by transmission electron microscopy images and x-ray diffraction. As a result, sequentially deposited Pt-Pd/C catalysts showed better electrochemical properties than those of simultaneously deposited Pt-Pd/C catalysts.

• Journal of the Korea Convergence Society
• /
• v.12 no.5
• /
• pp.17-22
• /
• 2021

Eco-friendly magnesium-air battery is a kind of metal-air battery known as a primary battery with a very high theoretical discharge capacity. This battery is also called a metal-fuel cell from the viewpoint of using oxygen in the atmosphere as a cathode active material and magnesium alloy as a fuel. Since battery performance is determined by the properties of the magnesium alloy used as a anode, more research and development of the magnesium alloy electrode as a anode material are required in order to commercialize it as a high-performance battery. In this study, the commercialized magnesium alloys(AZ31, AZ61) were selected and then electrochemical measurements and discharge test were conducted. Electrochemical properties of magnesium alloys were investigated by OCP changes, Tafel parameters and CV measurement, and the feasibilities of AZ61 alloy with excellent discharge capacity(1410mAhg^-1) as electrode materials were evaluated through CC discharge experiments.

• Journal of Electrochemical Science and Technology
• /
• v.13 no.4
• /
• pp.424-430
• /
• 2022

In the study, Ni²⁺ (nickel) removal from synthetically prepared wastewater by electrocoagulation method, which is one of the electrochemical treatment processes, was investigated and parameters such as current density, pH, mixing speed, initial Ni²⁺ concentration, supporting electrolyte type and concentration were determined to determine Ni²⁺ removal efficiencies effects were studied. Experiment conditions during 30 minutes of electrolysis; the current density was determined as 0.95 mA/cm², the initial pH of the wastewater was 6, the mixing speed was 150 rpm, and the initial nickel concentration was 250 mg/L. The Ni²⁺ removal efficiency was obtained as 75.99% under the determined experimental conditions, while the energy consumption was calculated as 3.15 kW-h/m³. In the experiments, it was observed that the type and concentration of the supporting electrolyte did not have a significant effect on the Ni²⁺ removal efficiency. In the trials where the effect of the support electrolyte concentration was examined, the Ni²⁺ removal efficiency was 75.99% in the wastewater environment without the supporting electrolyte, while the Ni²⁺ removal efficiency was 81.55% when 7.5 mmol/L NaCl was used after the 30-minute reaction, and the energy consumption was 2.15 kW-h/m³ obtained as. As a result of the studies, it was concluded that the electrocoagulation process can be applied in the treatment of wastewater containing Ni²⁺.

• Journal of Electrochemical Science and Technology
• /
• v.13 no.2
• /
• pp.279-291
• /
• 2022

In this report the thermochemical conversion of Sm₂O₃ to SmCl₃ using AlCl₃ in LiCl-KCl melt at 773 K is discussed. The final product was a mixture of SmCl₃, Al₂O₃, unreacted Sm₂O₃ and AlCl₃ in the chloride melt. The electrochemical attributes of the mixture was analyzed with cyclic voltammetry (CV) and square wave voltammetry (SWV). The crystallographic phases of the mixture were studied with X-ray diffraction (XRD) technique. The major chemical conversion was optimized by varying the effective parameters, such as concentrations of AlCl₃, duration of reaction and the amount of LiCl-KCl salt. The extent of conversion and qualitative assessment of efficiency of the present protocol were evaluated with fluorescence spectroscopy, UV-Vis spectrophotometry and inductively coupled plasma atomic emission spectroscopy (ICP-AES) studies of the mixture. Thus, a critical assessment of the thermochemical conversion efficiency was accomplished by analysing the amount of SmCl₃ in LiCl-KCl melt. In the process, a conversion efficiency of 95% was achieved by doubling the stoichiometric requirement of AlCl₃ in 50 g of LiCl-KCl salt. The conversion reaction was found to be very fast as the reaction reached equilibrium in 15 min.

• Journal of the Korean institute of surface engineering
• /
• v.57 no.4
• /
• pp.338-347
• /
• 2024

𝛼-MnO₂ as a cathode material for Zn-ion batteries allows insertion and extraction of Zn ions within its tunnel structure during charge and discharge. The morphology and crystal structure of 𝛼-MnO₂ particles critically determine their electrochemical behavior and energy storage performance. In this study, 𝛼-MnO₂ was synthesized from precursor solutions under varying pH conditions using a hydrothermal method. The effects of pH values on the morphology, crystal structure, and electrochemical performance were systematically analyzed. The analysis revealed that materials synthesized at higher pH levels exhibited elongated and narrow nanorods with a lower specific surface area. In contrast, those formed at lower pH levels showed shorter, thicker nanorods with a higher specific surface area. This increased surface area at a lower pH enhanced the specific capacitance by providing a greater electrode/electrolyte interfacial area. By contrast, the material synthesized at higher pH conditions demonstrated superior rate capability, attributed to its crystal structure with wider lattice spacings. Wide lattice parameters in the material synthesized at higher pH conditions facilitated easier ion transport than at lower pH levels. Consequently, the study confirms that adjusting the pH of the precursor solution can optimize the electrochemical properties of 𝛼-MnO₂ for Zn-ion batteries.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.5
• /
• pp.265-269
• /
• 2014

Carbon nanofiber electrode has been fabricated for energy storage systems by the electrospinning of SU-8 precursor and subsequent pyrolysis. Various parameters including the applied voltage, the distance between syringe tip and target collector and the flow rate of the polymer affect the diameter of SU-8 electrospun nanofibers. Shrinkage during pyrolysis decreases the fiber diameter. As the pyrolysis temperature increases, the resistivity decreases dramatically. Low resistivity is one of the important characteristics of the electrodes of an energy storage device. Given the advantages of carbon nanofibers having high external surface area, electrical conductivity, and lithium intercalation ability, SU-8 derived carbon nanofibers were applied to the anode of a full lithium ion cell. In this paper, we studied the physical properties of carbon fiber electrode by scanning transmission microscopy, thermal gravimetric analysis, and four-point probe. The electrochemical characteristics of the electrode were investigated by cyclic voltammogram and electrochemical impedance spectroscopy plots.

• Corrosion Science and Technology
• /
• v.7 no.2
• /
• pp.134-137
• /
• 2008

Cold arc welding of cast iron has been widely used with repair welding of metal structures. However its welding is often resulted in the galvanic corrosion between weld metal zone and heat affected zone(HAZ) due to increasing of hardness. In this study, corrosion properties such as hardness, corrosion potential, surface microstructures, and variation of corrosion current density of welding zone with parameters of used electrodes for cast iron welding were investigated with an electrochemical evaluation. Hardness of HAZ showed the highest value compared to other welding zone regardless of kinds of used electrodes for cast iron welding. And its corrosion potential was also shifted to more negative direction than other welding zone. In addition, corrosion current density of WM in polarization curves was qualitatively smaller than that of HAZ. Therefore galvanic corrosion may be apparently observed at HAZ. However galvanic corrosion may be somewhat controlled by using an optimum welding electrode.

• Corrosion Science and Technology
• /
• v.18 no.6
• /
• pp.267-276
• /
• 2019

The purpose of this study was to examine the influence of conditions for quenching and/or tempering on the corrosion and hydrogen diffusion behavior of ultra-strong automotive steel in terms of the localized plastic strain related to the dislocation density, and the precipitation of iron carbide. In this study, a range of analytical and experimental methods were deployed, such as field emission-scanning electron microscopy, electron back scatter diffraction, electrochemical permeation technique, slow-strain rate test (SSRT), and electrochemical polarization test. The results showed that the hydrogen diffusion parameters involving the diffusion kinetics and hydrogen solubility, obtained from the permeation experiment, could not be directly indicative of the resistance to hydrogen embrittlement (HE) occurring under the condition with low hydrogen concentration. The SSRT results showed that the partitioning process, leading to decrease in localized plastic strain and dislocation density in the sample, results in a high resistance to HE-induced by aqueous corrosion. Conversely, coarse iron carbide, precipitated during heat treatment, weakened the long-term corrosion resistance. This can also be a controlling factor for the development of ultra-strong steel with superior corrosion and HE resistance.

• Korean Journal of Materials Research
• /
• v.27 no.8
• /
• pp.422-430
• /
• 2017

Al/expanded graphite was successfully synthesized through a facile method including ultrasonic and heat treatment. In the well-designed three dimensional structure, expanded graphite(EG) works as a conductive matrix to support coated Al particles. The effects of the fabrication parameters on the microstructures and thermal conductivities of these composites were investigated. As a result, it was found that composites with graphite volume fraction of 17.4-69.4 % sintered at $600^{\circ}C$/45MPa exhibit in-plane thermal conductivities of 380-940 W/mK, over 90 % of the predictions by rule of mixture. According to the non-destructive analysis results, the synergistic enhancement was caused by the formation of efficient thermally conductive pathways due to the hybrid of the differently sized EG. The structure integrates the advantages of expanded graphite as a conductive support, preserving the electrode activity and integrity and improving the electrochemical performance.

• Journal of the Korean Vacuum Society
• /
• v.10 no.1
• /
• pp.61-66
• /
• 2001

$WO_3$ films were multicoated on the microscope slide glass and ITO-coated glass using a tungsten alkoxide type solution by the sol-gel deposition process. The effect of dipping and processing parameters on the structure, optical and electrochemical properties of the film were also investigated. Coating using alkoxide solution was very uniformed for low dipping speed of 0.005 m/s, but thickness variations across the sample became apparent for dipping speeds greater than 0.007 m/s. Electrochemical coloration experiments showed that films fired at lower temperatures color more easily than film fired to > $200^{\circ}C$. Rutherford backscattering spectroscopy studies revealed that $K^+$ ions were uniformly distributed throughout the $WO_3$layer in the colored sample.