• 방사성폐기물학회지
• /
• 제18권4호
• /
• pp.421-437
• /
• 2020

This study provides an assessment on a proposed method for separation of cesium, strontium, and barium using electrochemical reduction at a liquid bismuth cathode in LiCl-KCl eutectic salt, investigated via cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and scanning electron microscopy with energy dispersive X-ray spectrometry (SEM-EDS). CV studies were performed at temperatures of 723-823 K and concentrations of the target species up to 4.0wt%. Redox reactions occurring during potential sweeps were observed. Concentration of BaCl2 in the salt did not seem to influence the diffusivity in the studied concentration range up to 4.0wt%. The presence of strontium in the system affected the redox reaction of lithium; however, there were no distinguishable redox peaks that could be measured. Impedance spectra obtained from EIS methods were used to calculate the exchange current densities of the electroactive active redox couple at the bismuth cathode. Results show the rate-controlling step in deposition to be the mass transport of Cs+ ions from the bulk salt to the cathode surface layer. Results from SEM-EDS suggest that Cs-Bi and Sr-Bi intermetallics from LiCl-KCl salt are not thermodynamically favorable.

• Korean Chemical Engineering Research
• /
• 제55권1호
• /
• pp.107-114
• /
• 2017

고분자전해질 연료전지(PEMFC: polymer electrolyte membrane fuel cell)는 일산화탄소(CO)나 황화수소($H_2S$)가 포함된 연료가 주입될 경우 성능이 저하된다. 일반적으로 멀캅탄 계열의 부취제가 첨가된 탄화수소를 개질하여 생성된 수소에는 미량의 황화수소가 포함되어 있다. 본 연구에서는 황화수소를 수소에 첨가하여 anode에 주입하였을 경우에 연료전지 성능에 미치는 영향을 파악하고, 3가지 다른 회복방법인 순수 수소 주입법, 전위 순환법과 물 순환법을 적용한 경우의 회복률을 비교하여 보았다. PEMFC의 성능은 전기화학적 방법인 polarization curve, electrochemical impedance spectroscopy (EIS)와 cyclic voltammetry (CV)를 사용하여 분석하였다. 피독에 대한 회복방법인 순수 수소 주입법과 전위 순환법을 사용한 경우에는 회복률이 적었고, 물 순환법을 사용한 경우에는 초기에 대비하여 약 95% 이상 성능이 회복된 것을 확인하였다. 직접적으로 피독에 노출된 anode에 물을 흘린 경우의 성능회복률이 높았으며, cathode에 흘린 경우에도 물의 crossover에 의한 효과로 전위 순환법보다 우수한 회복률을 보였다. 이러한 연구결과로부터 황화수소 피독에 대한 회복기법을 구축함으로서 연료전지의 내구성을 향상시킬 수 있고, 불순물이 미량 함유된 저가 수소의 사용을 가능하게 함으로서 연료전지 보급에도 기여할 수 있을 것이다.

• Journal of Electrochemical Science and Technology
• /
• 제7권3호
• /
• pp.234-240
• /
• 2016

The effect of initial electrolyte loading (IEL) on cell performance in a coin-type molten carbonate fuel cell (MCFC) was investigated in this work. Since the material of MCFC depends on the manufacturer, optimisation requires experimental investigation. In total, four IEL values, 1.5, 2.0, 3.0, and 4.0 g, were used, corresponding to a pore filling ratio (PFR) of 38, 51, 77, and 102%, respectively. The cell performance with respect to the PFR was analysed via steady-state polarisation, step-chronopotentiomtery, and impedance methods. The electrochemical analyses revealed that internal resistance and overpotential of the cell decreased with increasing PFR, and a large overpotential was observed when the PFR was 102%, probably due to the flooding phenomenon. After operation, cross-section of the cell was analysed via surface analysis of SEM and EDS methods, and the remaining electrolyte was estimated by dissolution of the cell in 10 wt% acetic acid. A linear relationship between IEL and the weight reduction ratio by dissolution was obtained. Thus, the remaining amount of electrolyte could be measured after operation. The results of SEM and EDS showed that a PFR of 38 and 102% showed a lack and flooding of electrolytes at the cell, respectively, which led to a large overpotential. This work reports that MCFC performance is allowed only in the narrow range of PFR.

• 한국해양공학회지
• /
• 제23권4호
• /
• pp.64-68
• /
• 2009

It has been observed that coated steel structures deteriorate more rapidly than the designed lifetime due to acid rain caused by air pollution, etc. Therefore, improving the corrosion resistance of anti-corrosive paint is very important in terms of safety and the economic point of view. In this study, the corrosion resistance of five kinds of anti-corrosive paints, including the Acryl, Fluorine, and Epoxy resin series, were investigated with electrochemical methods, such as corrosion potential measurements, polarization curves, diffusion limiting current density, etc. As a result, the corrosion resistance of the F101 specimen with the fluorine resin series was found to be superior to the other specimens, while E100 with the epoxy resin series also showed a somewhat good corrosion resistance. Furthermore, it was observed that the amount of water and oxygen entering the inner side of a painted film increased with an increase in immersion time, irrespective of the kind of resin series. However, the oxygen diffusion limiting current density of a specimen with good corrosion resistance was relatively decreased compared to other specimens, because of the difficulty of oxygen diffusion penetrating to the inner side of the film. Consequently it is suggested that we can qualitatively evaluate the corrosion resistance of an anti-corrosive paint by measuring the diffusion limiting current density as an electrochemical method.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.260-262
• /
• 2002

The determination of DNA hybridization can apply the molecular biology research. clinic diagnostics. bioengineering, environment monitoring, food science and other application area. So, The determination of hybridization is very important for the improvement of DNA detection system. In this study, we report the characterization of the DNA hybridization by the electricalchemical methods. The probe oligonucleotide was used to determine the amount of target oligonucleotide in solution using Methylen Blue(MB) as the electrochemical indicators. The cathodic peak currents($I_{peak}$) of MB were linearly related to the concentration of the target oligonucleotide sequence in the range $1[{\mu}M]{\sim}0.1[{\mu}M]$. The detection limit of this approach was 0.01[nM]. As a result, the match oligonucleotide(CR-1) was most stable state and the peak of redox current measured by DNA hybridization detection sensors by using electrochemical method seem to be similar to 1-mer terminal mismatch oligonucleotide(MR-3). The MR-2, MR-3, MR-22 and MR-33 have each mismatching sequence of central and terminal. With this set the role of point mutations was to be investigated. Terminal mismatch oligonucleotide (MR-3, 33) is shown more stable state than central mismatch oligonucleotide(MR-2, 22). And 1-mer mismatch oligonucleotide(MR-2 or 3) is shown more stable state than 2-mer mismatch oligonucleotide(MR-22 or 33).

• 공업화학
• /
• 제23권2호
• /
• pp.153-156
• /
• 2012

본 연구에서 직접 메탄올형 연료전지용 담지 촉매의 전기 화학적 효율을 높이기 위하여 담지 촉매의 합성을 위한 2가지 다른 방법을 조사하였다. 담지 촉매에 있어서 합금을 형성하여 동시 담지하는 방법과 금속을 순차적으로 담지하는 방법을 비교하였다. 금속의 총 함량을 20 wt%를 사용하였으며, Pt-Pd의 금속비를 1 : 2로 하였다. 순환 전류-전압곡선(CVs), TEM 이미지와 XRD분석을 이용하여 두가지 다른 방법으로 제조된 촉매 간의 전기화학적 특성, 입자의 평균 크기 및 결정의 구조 변화를 비교 분석하였다. 그 결과, 순차적 금속 담지 촉매가 동시 담지 촉매보다 단위 무게당 산화전류 수치를 나타내어 보다 높은 전기활성 특성을 보였다.

• 한국고분자학회지:고분자과학과기술
• /
• 제23권3호
• /
• pp.307-312
• /
• 2012

• 한국재료학회지
• /
• 제19권11호
• /
• pp.596-600
• /
• 2009

Electrochemical deposition characteristics of CdSe nanorods were investigated for hybrid solar cell applications. CdSe nanorods were fabricated by electrochemical method in $CdSO_4$ and $H_2SeO_3$ dissolved aqueous solution using an anodic aluminum oxide (AAO) template. Uniformity of CdSe nanorods was dependent on the diameter and the height of holes in AAO. The current density, current mode, bath composition and temperature were controlled to obtain a 1:1 atomic composition of CdSe. CdSe nanorods deposited by direct-current method showed better uniformity compared to those deposited by purse-current and/or purse-reverse current methods due to the bottom-up filling characteristics. $H_2SeO_3$ concentration showed more significant effects on pH of solution and stoichiometry of deposits compared to that of $CdSO_4$. A 1:1 stoichiometry of uniform CdSe nanorods was obtained from 0.25M $CdSO_4-5$ mM $H_2SeO_3$ electrolytes with a direct current of 10 $mA/cm^2$ at room temperature. X-ray diffraction and electron diffraction pattern investigations demonstrate that CdSe nanorods are a uniform cubic CdSe crystal.

• 전기화학회지
• /
• 제5권1호
• /
• pp.1-6
• /
• 2002

졸-겔법을 이용하여 미량의 은이 도핑된 $Ag_xV_2O_5$ xerogel(x=0.06, 0.11, 0.22)을 합성하여 리튬이차전지용 양극 소재로서 전기화학적 특성을 연구하였다. $Ag_xV_2O_5$ xerogel은 무정형의 층상구조로 열처리하면 orthorhombic 구조로 전환되었으며, 표면구조는 $V_2O_5$와 유사한 단위체가 서로 얽혀 일정한 방향으로 성장하여 비등방성 fibril을 형성하고 있다. $Li/Ag_xV_2O_5$ xerogel셀의 전지 용량(specific capacity)은 10mA/g의 방전율에서 평균 359mAh/g, 싸이클 효율 $94\%$이상이었으며, 바나듐산화물에 첨가된 미량의 은에 의해 전기화학적 특성이 향상되었다. NMR실험으로 서로 다른 환경의 $Li^{+}$이온이 전극에 존재함을 확인하였다.

• Journal of Electrochemical Science and Technology
• /
• 제3권3호
• /
• pp.123-134
• /
• 2012

The electrochemical performance of positive pole grids of lead-acid batteries made of Pb-0.08%Ca-1.1%Sn alloys without and with 0.1 wt% of each of Cu, As or Sb and with 0.1 wt% of Cu, As and Sb combined was investigated by electrochemical methods in 4.0 M $H_2SO_4$. The corrodibility of alloys under open-circuit conditions and constant current charging of the positive pole, the positive pole gassing and the self-discharge of the charged positive pole were studied. All impurities (Cu, As, Sb) were found to decrease the corrosion resistance, $R_{corr}$ after 1/2 hour corrosion, but after 24 hours an improvement in $R_{corr}$ was recorded for Sb containing alloy and the alloy with the three impurities combined. While an individual impurity was found to enhance oxygen evolution reaction, the impurities combined significantly inhibition this reaction and the related water loss problem was improved. Impedance results were found helpful in identification of the species involved in the charging/discharging and the self-discharge of the positive pole. Impurities individually or combined were found to increase the self-discharge during polarization (33-68%), where Sb containing alloy was the worst and impurities combined alloy was the least. The corrosion of the positive pole grid in the constant current charging was found to increase in the presence of impurities by 5-10%. Under open-circuit, the self-discharge of the charged positive grids was found to increase significantly (92-212%) in the presence of impurities, with Sb-containing alloy was the worst. The important result of the study is that the harmful effect of the studied impurities combined was not additive but sometimes lesser than any individual impurity.