• Journal of Biosystems Engineering
• /
• v.39 no.2
• /
• pp.101-110
• /
• 2014

Purpose: The purpose of this study is to develop a system to optimize drying potential energy of the exhausted hot air by changing relative humidity of the air. This study modified the conventional drying method into a drying method changing exhaust cycle and time in order to control the relative humidity of the exhausted hot air during drying process. Method: A valve on the vent was controlled according to a preset time to change the exhaust cycle and time. This study analyzed the influence of the two different types of drying method on the drying characteristics, required energy, and quality of the dried peppers: conventional drying method exhausting hot air continuously and new drying method controlling exhaust cycle and time. Results: Drying characteristics based on exhaust time showed that drying time increased with exhaust time, and specific energy consumption was reduced by 28% from 18.39 MJ/kg (conventional method) to 13.24 MJ/kg when exhaust time was set to one minute. Drying characteristics based on heating time showed that drying time increased with heating time and specific energy consumption was reduced by 30% from 18.39 MJ/kg (conventional method) to 12.87 MJ/kg when exhaust time was set to 22 minutes. Drying characteristics based on exhaust cycle showed that drying time increased with exhaust cycle, and specific energy consumption was reduced by 31% from 18.39 MJ/kg (conventional method) to 12.69 MJ/kg when exhaust time was set to one minute and exhaust cycle was set to 22 minutes before drying and 40 minutes after drying. The quality of the dried red peppers showed that capsaicin, color, and sugar content were high as 34.87 mg/100g, 66.33, and 11.87%, respectively, when exhaust time was set to one minute and exhaust cycle was set to 22 minutes before drying and 40 minutes after drying. Conclusions: In order to utilize the drying potential energy of the exhausted air during drying process, the conventional drying method was modified into the drying method controlling exhaust cycle and time. The results showed that drying with exhaust cycle of one minute was more efficient in terms of drying time, required energy, and quality of the dried peppers than the one with exhaust cycle of 20~40 minutes.

• Journal of Biosystems Engineering
• /
• v.38 no.1
• /
• pp.41-47
• /
• 2013

Purpose: The objectives of this study were to construct the solar drying system with evacuated tubular solar collector and to investigate its performance in comparison with indoor and outdoor dryings. Methods: Solar drying system was constructed with using CPC (compound parabolic concentrator) evacuated tubular solar collector. Solar drying system is mainly composed of evacuated tubular solar collector with CPC reflector, storage tank, water-to-air heat exchanger, auxiliary heater, and drying chamber. Performance test of solar drying system was conducted with drying of agricultural products such as sliced radish, potato, carrot, and oyster mushroom. Drying characteristics of agricultural products in solar drying system were compared with those of indoor and outdoor ones. Results: Solar drying system showed considerable effect on reducing the half drying time for all drying samples. However, outdoor drying was more effective than indoor drying on shortening the half drying time for all of drying samples. Solar drying system and outdoor drying for oyster mushroom showed the same half drying time. Conclusions: Oyster mushroom could be dried easily under outdoor drying until MR (Moisture Ratio) was reached to about 0.2. However, solar drying system showed great effect on drying for most samples compared with indoor and outdoor dryings, when MR was less than 0.5.

• International Journal of Highway Engineering
• /
• v.20 no.4
• /
• pp.35-46
• /
• 2018

PURPOSES : The purpose of this study is to compare the lane curing time of natural drying and a lane drying device when painting lines on a highway. METHODS : The painting process was carried out in July 2015 and September 2015, respectively, for the Gimcheon IC - Gimcheon JC. After the painting, measurements were obtained three times at six measurement points located at 20 m intervals on the shoulder line and the dividing line. The curing time was measured for natural drying and drying using a lane drying device, and compared for different pavement types (asphalt, concrete) and paint types (waterborne paint, methyl methacrylate paint). RESULTS : The results of the lane curing time comparison on the highway are as follows. The combination of asphalt and methyl methacrylate paint cured more rapidly during both the natural drying and drying using the lane drying device. Finally, it was cured at least 32.2% and 40.7% faster when using a drying device than in natural drying. CONCLUSIONS : The comparison of lane curing time of the highway showed that the combination of asphalt and methyl methacrylate paint cured more rapidly when using both natural drying and a lane drying device.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10b
• /
• pp.132-137
• /
• 1993

In this paper, a fish drying process control system is proposed, which predicts the proper change with time in weight of the material fish and the drying conditions in advance, based on the performance of skilled worker. In order to implement a human expertise into an automated fish drying process control system, an experimental analysis is made and a model for the process is built. The proposed system divided into two procedures: The procedure before drying and the one during drying. The procedure before drying is for the prediction of necessary drying time. To estimate the necessary drying time, first, the proper change in weight for the product is obtained by using fuzzy reasoning. The condition part of the production rule consists of the factors of fish body and the expected degree of dryness. Kext, the necessary drying time is obtained by regression models. The variables employed in the models are the factors, inferred change in weight and drying conditions. The model for the procedure during drying is also proposed for more accurate estimation, which is described by a system of linear-differential equations.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.34 no.12
• /
• pp.2062-2072
• /
• 2010

This research evaluates the change of the water absorbency and drying speed of a quick-drying knit fabric by repeated laundering and laundering conditions and investigates the influence of laundering conditions on the functional properties of the knit fabric. Four factors of laundering conditions were studied: detergent, water hardness, water temperature, and frequency of rotation. Knit fabrics were washed for 25 laundering cycles in a drum-type washing machine with nine different laundering conditions derived from an orthogonal array. The properties of knit fabrics were measured with a drop absorption test, a strip test, and a drying time test. Relaxation shrinkage pointed to a change in the structural characteristics of the knit fabric. Wetting time was faster and wickability was greater in the knit fabrics that underwent 5 laundering cycles; in addition, there were no obvious changes in wetting time and wickability. The detergent was the most important factor in wetting time (40.4%) and wickability (60% or above). Water hardness, water temperature and RPM had less of an effect on wetting time and wickability. There were no significant differences between the levels of laundering conditions (except for detergent) on wetting time and wickability. Drying times with neutral and alkali were slower by repeated laundering; however, there was no obvious change in drying time. Hardness, water temperature and RPM had less of an impact on drying time.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.1321-1326
• /
• 2008

A study on the heat and mass transfer for the drying time in spray freezing drying process was experimentally presented in this paper. A spray freezing dryer for the production of an inhalable powder medicine is developed and an albumin solution as protein specimen is adopted. The freeze-drying for the albumin solution is tested in three different height of the particles piled up in a tray such as 2 mm, 5 mm, 7 mm, and the drying time is estimated as 10 h, 15 h, 22 h. From this results, the correlation is suggested and the drying time with various height of the particles piled up in a tray can be estimated. The assessment on the drying time is conducted thought a microbalance and the rate of water content is measured. The results based on temperature and weight are compared. The difference of the results happens due to the heat transfer from the lateral side of the vial. It is thought that the better estimation in drying time can be predicted by considering the heat transfer effect.

• Journal of Biosystems Engineering
• /
• v.31 no.5 s.118
• /
• pp.416-422
• /
• 2006

Drying characteristics of green onion and onion during fluidized and fixed bed drying were investigated and compared. Sliced peen onion and onion were dried at drying air temperature of 45, 55, and $65^{\circ}C$. Drying air velocity during fluidized bed drying was adjusted with drying time at each drying temperature. Drying time to reach a given final moisture content was shorten in fluidized bed drying than in fixed bed drying - for drying temperature of 45, 55, and $65^{\circ}C$, the differences were 60, 60, and 50 min for green onion and 360, 180, and 60 min for onion. Drying constant (K) was greatly affected by drying method and drying temperature. Terminal velocity under fluidized bed drying was decreased exponentially for green onion and linearly (or onion with increase of drying temperature. Also, terminal velocity had linear relationship with moisture content for both green onion and onion.

• Journal of Biosystems Engineering
• /
• v.37 no.1
• /
• pp.36-43
• /
• 2012

Purpose: Drying characteristics of the sliced carrot and green pumpkin were investigated by using the waste heat dryer. Methods: The effects of drying temperature ($T$) and slice thickness affecting drying time were analyzed. Mathematical models for the drying curves were determined with statistical analysis of drying data. Effective diffusivity was determined for the slices of carrot and green pumpkin under various drying conditions. Results: Drying time was reduced at the drying conditions of thinner slice and higher drying temperature. Moisture ratio ($MR$) according to drying time ($t$) was well presented as an exponential function at all of drying conditions for the slices of carrot and green pumpkin with the determination coefficient ($r^2$) of >0.99. The values of effective diffusivity ($D_{ff}$) of the slices for carrot and green pumpkin were increased with increasing the drying temperature. The relationship between Ln($D_{ff}$) and $1/T$ was linear with the determination coefficient ($r^2$) of >0.97. Conclusions: Drying model was well established as an exponential function at all of drying conditions for drying samples.

• Environmental Engineering Research
• /
• v.24 no.4
• /
• pp.529-542
• /
• 2019

Nowadays, drying methods for municipal solid waste quality improvement have been adopted in the developed and developing countries to valorize wastes for a renewable energy source, reduce dependency on fossil fuel and keep safer disposal at landfills. Among them, biodrying, biostabilization, thermal drying and solar drying are the most common. Drying of municipal solid waste could offer several environmental and economic benefits. Therefore, this review highlighted the drying methods for municipal solid waste quality improvement around the world and compared them based on the reduction of moisture, weight and volume of municipal solid wastes against drying temperature and time by using statistical analysis. It was observed that the drying temperature of different drying methods accounted for 115 ± 40℃ for thermal drying, 59 ± 37℃ for solar drying, 55 ± 15℃ for biodrying and 58 ± 11℃ for biostabilization. Among the drying methods, thermal drying provided the shortest drying time. The moisture reduction, weight reduction, volume reduction and heating value increase of municipal solid waste could vary with drying temperature and time. Finally, the benefits and drawbacks of different drying methods were specified, and recommendations were made for the future efficient drying.

• Fashion & Textile Research Journal
• /
• v.10 no.6
• /
• pp.1058-1063
• /
• 2008

The use of clothes dryers is increasing in Korea and throughout Asia, because of preference for the drum type washer dryer. Clothes dryers consume more energy than almost any other home appliance. This paper suggests efficient ways for drying laundry with condensing clothes drier. We dried cotton fabrics with the condensing clothes dryers and observed the energy input, temperature and RH of the dryer during the drying process. In the early stages of drying process, the air temperature inside the clothes dryer decreased and the RH and the drying time increased as the weight of fabrics increased. We found that it was important to consider the total weight of the fabrics that included heat-sensitive fibers. It took more than half the drying time and the energy input for a 2.5 kg load that it did for a 5 kg load. Therefore, drying larger one load was more efficient than divided smaller loads, because increasing the weight of the fabrics reduced the energy input per kg of drying clothes. The lower the initial moisture regains of the fabrics were, the lower the energy input and the drying time were. The energy input for spinning after washing was much less than that for drying in the dryer. Consequently, it is more efficient to reduce the moisture content of the clothes by lengthening the spinning time of the washer to reduce the energy consumption and the drying time. During the drying process opening the door twice for 30 seconds each time lowered the air temperature and the RH of the dryer, but did not affect the moisture regain of the fabrics, the drying time, and the energy input.