• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1996년도 제24회 춘계학술대회
• /
• pp.86-93
• /
• 1996

The lubrication characteristics of high-speed ball bearings has been investigated empirically using 45mm bore split inner ring ball bearings employed in small industrial gas turbine engines with oil-jet lubrication method. For the close structural simulation, experiments carried out with bearing mounting supports of real engines, such as bearing housings and oil nozzle assemblies with squeeze film dampers. Thus the results of tests can be directly applied to the design and the development of gas turbine engines. Testing was done by varying operating speeds, axial load on bearings, and lubricant flowrates. During testing, the temperature of bearing at outer-ring face, the power consumption of the driving motor, and the rotating resistance of the bearing were measured. From this study, the representative factors for lubrication characteristics at high speed was found, and the most important one was not operating speed but axial load up to 1.95 million dmN speed and 303 kgf axial load. Furthermore, the detailed variation of the rotational resistance of the bearing could be visualized by measuring the change of the radial load under the bearing supports. The rotational resistance consists of the frictional resistance and the bearing-cavity oil resistance.

• 한국소음진동공학회논문집
• /
• 제22권10호
• /
• pp.949-958
• /
• 2012

Position tracking control of a link of a slave manipulator which needed to track the corresponding link of a master manipulator was addressed in this paper. Since driving torque from motor is transmitted through a set of flexible cable to link, the motion control system is modeled by a two-mass model connected with elastic coupling which has finite stiffness. Relative vibration of two-mass resonant system is a serious problem to operate manipulator. This paper proposed sliding mode control to reduce resonant vibration and fine position tracking control. Also, a pseudo-sliding mode control which uses a saturation function instead of a signum function was discussed and showed that the pseudo-sliding mode control can improve disturbance regulation performance as well as guarantees fine command tracking without chattering which is an inherent drawback of basic sliding mode control. In addition, a disturbance observer based sliding mode control has been suggested to improve disturbance regulation performance. The feasibility of the proposed control design was verified along with some simulation results.

• 한국산업융합학회 논문집
• /
• 제22권6호
• /
• pp.711-719
• /
• 2019

At present, wind power is the fastest growing technology in the world. The domestic market depends heavily on imports for wind tower lift. so it manage through the overseas maker. The lift manufacture, establishment and maintenance utility is increasing, localization development of one wind tower lift is necessary with domestic fundamental base technique. In this paper, we will study the components necessary for the development of onshore offshore wind tower elevators, which are currently dependent on total imports, in line with the high growth of the wind market and the enlargement of the wind power generators. First of all, endless winders and cabins, which are the core components of the offshore wind tower lift, were examined for the components that affect the structural safety. Structural analysis was performed on Sheave, which is responsible for most of the lift lifting loads, and Block Stop, a safety device that prevents the cabin from falling in an emergency. The structural suitability was evaluated by comparing with the safety factor. In addition, the on-board control panel combines the control panel of the elevator and the drive motor driving the endless winder for efficient control of the offshore wind tower lift. The addition of features improves ride comfort at departure.

• 자동차안전학회지
• /
• 제13권4호
• /
• pp.60-65
• /
• 2021

The event data recorders (EDR) have been used as a device to help understand traffic accidents. With the recent development of autonomous vehicle (AV), it has become important to prepare the new EDR for AV. Therefore, the purpose of this study is to propose the direction of EDR-AV recording. First of all, the recent EDR data elements and the data elements of AV under discussion at UNECE WP29 EDR/DSSAD (Data Storage System for Automated Driving) were analyzed. The consumer complaint database in Motor Vehicle Recall Center in Korea was analyzed in order to utilize cases of domestic traffic accidents related to advanced driver assistance systems (ADAS). Consequently, problems with existing EDR were identified through unclear accident cases related to ADAS. In the future, it was proposed to record images in which the ADAS perception systems recognize the surroundings of the accident site as an EDR-AV recording item.

• 한국인터넷방송통신학회논문지
• /
• 제21권1호
• /
• pp.115-120
• /
• 2021

본 논문에서는 비례공진 전류제어기 기반의 단상 영구자석 동기전동기의 운전 알고리즘을 제안하였다. 일반적으로 단상 영구자석 동기전동기의 경우 회전자의 형상에 따른 비대칭 공극이 발생할 수 있으며, 이는 고속 운전시 소음과 진동의 원인이 된다. 따라서 본 논문에서는 제어 안정성이 뛰어난 비례공진 전류제어기를 적용한 단상 영구자석 동기전동기의 운전 알고리즘을 제안하였다. 비례공진 전류제어기법은 정상상태 오차가 없고 왜란에 대해 비교적 강인한 특성을 가지고 있으며, 복잡한 연산과정 없이 교류입력의 정상상태를 제거할 수 있다. 제안한 알고리즘의 유효성과 타당성을 실험을 통해 검증하였다.

• 한국산업융합학회 논문집
• /
• 제25권1호
• /
• pp.55-60
• /
• 2022

This study conducted the measurements of air flow rate for blower systems with experiment and numerical. A new airflow rate test method is suggested, with which it is possible to accurate measurements and calculate the air flow rate for blower systems. The blower(axial fan) is an industrial fluid machine device that supplies a large amount of air by driving an impeller with an electric motor, and it is widely used throughout the industry such as steel, power plant, chemical, semiconductor, LC D, food, and cement. The airflow from the blower is for exchanging the heat in the cooling unit or heat exchanger. The temperature of coolants and hydraulic oil primarily depends on the amount of airflow rate through the cooling package so its accurate estimation is very important. Moreover, it required a larger investment in time and cost since it could not be executed until the system is actually made. Therefore, this research is intended to examine the phenomenon of air flow pattern when testing air flow rate, suggested new test method, and show the result of the validation test.

• 한국전자통신학회논문지
• /
• 제17권6호
• /
• pp.1293-1300
• /
• 2022

본 논문에서는 아이들을 태우는 유아차로부터 생길 수 있는 각종 안전사고를 예방 그리고 보다 수월한 유아차 사용을 위한 연구를 진행하였다. 유아차가 보호없이 주행하는 것을 막기 위하여 압력센서와 서브모터를 활용하여 유아차 바퀴에 브레이크 기능을 탑재하였으며 압력센서와 LCD를 활용하여 안전벨트 결속의 유무를 판단하여 유아가 유아차에서 떨어지는 것을 방지할 수 있도록 설계하였다. 추가로 LCD와 LED를 활용하여 일정 온습도를 넘어가면 경고등이 켜지도록 설계하여 유아가 유아차를 사용할 때 쾌적한 환경에 있을 수 있도록 설계하였다.

• 한국인터넷방송통신학회논문지
• /
• 제23권4호
• /
• pp.143-148
• /
• 2023

SRM의 특성 중 비선형성으로 인해 최대토크 및 최소 토크 맥동 형성을 위한 적정 운전이 어렵다. 또한 고정 스위칭각 제어 때 속도 가변에 따른 토크 형성이 불안정하여 효율을 저하시키는 문제점을 가지고 있다. 따라서 속도 가변에 따른 능동적인 스위칭각 제어가 필요하다. 본 논문에서는 SRM의 비선형성으로 인한 문제점으로부터 선행각 (Advance angle)의 자동제어에 의한 토크 리플 저감과 이에 따른 출력 토크 향상에 의한 구동 성능개선을 위한 방법에 대해 모색하였다. 또한 히스테리시스 전류제어기 성능에 따른 스위칭 가변으로 인한 SRM의 최적 운전에 대해 살펴보았다.

• 한국IT서비스학회지
• /
• 제22권3호
• /
• pp.49-63
• /
• 2023

The inclusion of software and wireless communication devices in vehicles has raised concerns regarding automobile security. In its response, UNECE WP.29 implemented the first-ever international standard for automotive cyber security in June 2020. Yet, the existing disparity between national standards for automotive certification systems and 「UN Regulation No. 155」 has caused confusion among auto makers. This discrepancy not only jeopardizes the security of domestic vehicles but also poses challenges to the seamless import and export of automobiles. Hence, there is a need to enhance the automotive cyber security certification system; however, there is a dearth of scholarly discourse on this topic. Consequently, this study presents a proposal for enhancing the domestic automotive cyber security certification system. In view of this, existing legal frameworks such as the 「Motor Vehicle Management Act」 and the 「Self-Driving Vehicle Act」 were reviewed, along with domestic and international automotive certification systems. The recommendations for improvement, derived from the findings, encompass institutional, legal, and operational aspects. This study is highly significant as it examines both domestic and international automotive certification systems in an area where there is a lack of academic discussion.

• 한국전자통신학회논문지
• /
• 제18권3호
• /
• pp.433-440
• /
• 2023

반사경이 차량에 의해 충돌되는 경우나 폭풍 등으로 돌아가는 경우, 충격 센서에 의해 이벤트가 뜨고 트리거가 작동된다. 본 논문의 트리거 처리 알고리즘은 자이로 센서의 X, Y, Z값을 등록된 값과 비교하여 3축 구동 모터의 작동에 의해 원래의 값으로 구동되도록 제안한다. 그리고 차량번호판을 인식해서 도난이나 사회적인 문제가 되는 차량이면 경찰 작전망에 정보제공 처리한다. 반사경이 도난이나 위치 이동이 발생하는 경우, 등록된 GPS값을 가지고 있기 때문에 도난 모니터링 기능을 작동하여 처리할 수 있도록 한다.