• Journal of the Korean Wood Science and Technology
• /
• v.48 no.4
• /
• pp.450-457
• /
• 2020

Single pellet press technology allows for fast, low-cost, and small-scale tests to investigate pelletizing characteristics. We estimated proper compression ratios for five Korean domestic wood species through predicted relationships between pelletizing pressure P_x and compression ratio based on experimental data obtained from a single pellet press unit. The pressures required to obtain a 6-mm-diam pellet of density 1200 kg/㎥ were estimated as 111 MPa for Populus davidiana, 133 MPa for Robinia pseudoacacia, 136 MPa for Quercus mongolica, 97 MPa for Pinus densiflora, and 127 MPa for Pinus rigida. On the basis of these pressures, we estimated proper compression ratios to be within the range 7.676-8.410 for these species, and we found the compression ratios needed for hardwood species to be somewhat higher than those needed for softwood species to obtain the pellet density of 1200 kg/㎥.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.2
• /
• pp.202-212
• /
• 2017

This study was to establish the interrelation between chemical compositions and near infrared (NIR) spectra for the classification on distinguishability of domestic gymnosperms. Traditional wet chemistry methods and infrared spectral analyses were performed. In chemical compositions of five softwood species including larch (Larix kaempferi), red pine (Pinus densiflora), Korean pine (Pinus koraiensis), cypress (Chamaecyparis obtusa), and cedar (Cryptomeria japonica), their extractives and lignin contents provided the major information for distinction between the wood species. However, depending on the production region and purchasing time of woods, chemical compositions were different even though in same species. Especially, red pine harvested from Naju showed the highest extractive content about 16.3%, whereas that from Donghae showed about 5.0%. These results were expected due to different environmental conditions such as sunshine amount, nutrients and moisture contents, and these phenomena were also observed in other species. As a result of the principal component analysis (PCA) using NIR between five species (total 19 samples), the samples were divided into three groups in the score plot based on principal component (PC) 1 and principal component (PC) 2; group 1) red pine and Korean pine, group 2) larch, and group 3) cypress and cedar. Based on the chemical composition results, it was concluded that extractive content was highly relevant to wood classification by NIR analysis.

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.6
• /
• pp.470-479
• /
• 2010

In this study, the visual grading based on the visual characteristics and structural timber bending test were conducted for domestic yellow poplar dimension lumber. Structural performance of domestic yellow poplar dimension lumber was conducted through the evaluation of strength and stiffness. Visual grading rule of yellow poplar dimension lumber did not exist in Korea. Visual grading of yellow poplar dimension lumber was performed according to the NSLB (Northern Softwood Lumber Bureau) standard grading rules including several hardwood dimension lumber. The allowable bending stress was calculated from the results of a visual grading. Compared with NDS (National Design Specification), the yellow poplar dimension lumber showed enough strength for structural uses. In addition, the visual grading was performed according to the KFRI (Korea Forest Research Institute) grading rule to calculated allowable bending stress and to evaluated the feasibility. The yellow poplar was classified into the pine groups by the KFRI criteria regulated by specific gravity. Allowable bending stress based on weibull distribution had became highly than KFRI criteria, as No. 1 (10.0 MPa), No. 2 (7.4 MPa) and No. 3 (4.1 MPa). And the availability of yellow poplar dimension lumber for structural uses had been confirmed. The Modulus of Elasticity (MOE) of domestic yellow poplar dimension lumber had not met the NDS and KFRI criteria. However, for the use of domestic yellow poplar, average values of MOE which obtained through this test were suggested as design value for domestic yellow poplar. Design values were supposed No. 1, 2 (9,000 MPa) and No. 3 (8,000 MPa).

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.5
• /
• pp.444-450
• /
• 2011

The goal of this study is to investigate bending properties of domestic timber. Three representative structural timber from Larix kaempferi, Pinus koraiensis, and Pinus densiflora, in the northeastern South Korea were selected. Visual grading for the timber was conducted based on KFRI notification 2009-01 and the bending strength for the timber was evaluated based on ASTM D 198 bending. The high percentage of grade 1 and 2 for Larix kaempferi shows that the KFRI notification was optimized for this species. The bending strength distributions from Pinus koraiensis and Pinus densiflora were very similar. It could be possible to specify the allowable bending properties of these two Specification using a united species group similar to spruce-pine-fir. Lastly, the bending strength of $120{\times}180mm$ structural members was higher than both existing values in KBC 2009 and design values for timber of imported species described in the NDS. Thus, 120 mm thick domestic softwoods could replace the commercial imported species and the KBC should be modified to provide design values for both timber and dimensional lumber, respectively, like NDS.

• Journal of the Korean Society of Tobacco Science
• /
• v.22 no.2
• /
• pp.164-169
• /
• 2000

The reconstituted tobacco leaves(RTL) playa major part in the control of the low density and tar cigarette. Reconstituted tobacco manufactured by the papermaking process has much higher filling power than homogenized tobacco manufactured by slurry and rolling process. Fragile reconstituted tobaccos are liable to lead to small particles detrimental for filling power so they must be properly flexible. This work was conducted to determine the effect of CaCO$_3$ addition in paper-making process on the filling power and the flexibility of the reconstituted tobacco and to obtain the fundamental informations for improving the quality of domestic reconstituted tobacco. We analyzed the wood fiber species, the filler level, the fiber length, the fineness level and observed the surface of the RTL. From the obtained results, we could determine that foreign reconstituted tobacco was manufactured by blending softwood with hardwood and over 8% of calcium carbonate at the addition level. The domestic RTL has much higher fine fiber level by 23.2 % than that of foreign, so the refining treatment process and the condition must be reoptimized for the improvement of RTL quality.

• Journal of the Korea Furniture Society
• /
• v.25 no.3
• /
• pp.233-237
• /
• 2014

The eco-friendly preservatives such as ACQ or CUAZ have been used in landscape architectural facilities these days. In this study, the decay efficacies of ACQ treatments were evaluated according to domestic veneer species, concentration of ACQ, weathering test, adhesive type, and fungus type. In case of veneer species, hinoki cypress and yellow poplar showed the highest and lowest decay resistance, respectively. And the decay resistance appeared to be greater in plywoods bonded by resorcinol resin-bonded plywood and non-weathering treated plywood than polyurethane resin-bonded plywood and weathering treated plywood.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.4
• /
• pp.337-345
• /
• 2013

Log grading rules are essential tools to ensure the quality of logs in distribution structure. The rules should reflect the long experience and accepted usage practice in the market. A gap between the rules and market should be improved based on analysis of log qualities that produced and market demand. In this study more than ten millions logs which were produced by 5 Regional Forest Services in 2010~2011 period, were analyzed in their qualities including diameters and lengths by species. A proposal was driven to improve the current log grading rules in terms of log diameter classes and length. The followings are the summary of this study. Most of domestic softwood logs are belong to small diameter class of 100~160 mm, which imply the diameter classes of current log grading rules are immoderate. Distributions of log diameter shows distinctive patterns by species, which indicate a necessity of differentiated diameter classes by species in an improved rules. Lengths of logs in productions do not corresponding to the demands and preferences in sawmills. Therefore it is highly recommended to include log length term in an improved log grading system. Based on these findings, 6 log grading systems for 3 species groups of softwood are newly proposed to improve current log grading rules. Limits of log diameter and log length are also proposed for each log grading system.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.6
• /
• pp.832-846
• /
• 2020

The purpose of this research was to evaluate the vapor permeability of nine different species of domestic softwood and the vapor permeability evaluation through the production of small wall structures for the developing applications, utilizing the vapor permeability of wood. In addition, the permeability evaluation was attempted by means of the production of a small wall structure injected with a waste material, bottom ash, as a moisture absorbent for improving the permeability. Consequently, the results of the vapor permeability evaluation by means of S_d value are as follows: (1) It was observed that Abies holiphylla, Picea jezoensis, Ginkgo biloba, Pinus koraiensis and Pinus rigida are permeable to moisture among 9 species of domestic softwood in Korea. (2) By means of this, semi-permeability efficiency was evaluated when producing a small wall structure. (3) Besides, improved effects of permeability were evaluated when producing a small wall structure inserted with bottom ash. As a result, it was confirmed that the S_d value of Pinus koraiensis turned out to be 1.63, which is superior to other 8 tree species.

• Journal of the Korea Furniture Society
• /
• v.21 no.2
• /
• pp.188-195
• /
• 2010

This study has been focused on the evaluation of domestic softwood timbers to replace imported timbers for woodcrafts and furniture-making. Figures on radial and tangential sections were observed with naked eyes. As the result of study on the figures appeared on the wood surface of 6 species of trees, flat grain and edge grain were clearly found from Taxus cuspidata. Juniperus chinensis and Ginkgo biloba had wavy grain figure and pigment figure, and blister figure was found in Pinus densiflora, Larix kaempferi showed pitch streak and irregular figures on its tangential section due to growth abnormalities. Wavy grain figure appeared weakly on near knot of Pinus koraiensis. The characteristic figures shown from each species of trees are expected to be used for crafts, sculptures, furniture, and interior decoration. They are also considered to have great potential to substitute imported timber sufficiently, which are currently used a lot for wood crafts and furniture-making.

• Journal of Korean Society of Forest Science
• /
• v.81 no.2
• /
• pp.124-138
• /
• 1992

This study was carried out to estimate long-term demand functions, and to project consumption of roundwood to the year 2030, using time series data for the period 1970-1990. Especially, the unique features of this study are in the estimation of demand functions for roundwood by species group and by end-use with help of dummy variables. It also, attempts to show how dummy variables can be utilized for improving the estimation result. The result of this study reveals that hardwood roundwood consumption is being substituted by softwood roundwood due to the rapid increase in the relative price of softwood, and this trend is expected to continue in the near future. The consumption of roundwood by mining industry is projected to fall as the coal :mining is expected to decline. The parametric estimates of timber demand function by species group and by end-use indicate that the demand for timber in Korea is more responsive to the performance of domestic economy as a whole, represented by GDP in this study, than to other variables such as own and substitute prices. The effects of population growth and substitute prices could not be determined.