• Proceedings of the KIEE Conference
• /
• 2002.07d
• /
• pp.2043-2045
• /
• 2002

When the input is small, increase of the input leads to a corresponding increase of output, but when the input reaches a certain level, its further increase does produces little or no increase of the output. When this phenomenon happens, the device is said to be in saturation. Occurence of saturation amounts to reducing the gain of the device as the input signals are increased. An extreme case of saturation is the on-off or relay nonlinearity. On-off nonlinearitics have effects similar to those of saturation nonlinearities. Furthermore they can lead to "chattering" in the physical systems doc to their discontinuous nature. This paper presents stabilization method of saturation nonlinearity system using deadzone describing function etc.. And computer simulation results show that saturation nonlinearity can be eliminated due to deadzone nonlinearity.

• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.1940-1943
• /
• 1998

A new PWM rectifier which offers a unity power factor is proposed. The circuit has same inductance as the conventional boosting type PWM rectifier in powering mode, but the inductance is splitted to 2 part in freewheeling mode. So the period of freewheeling mode is shorter than that of conventional boosting type PWM rectifier, and discontinuous input current is obtained in wide duty range. Therefore the proposed PWM rectifier accomplishs a unity power factor in wide range of duty ratio and boosting factor. And the conventional boosting type PWM rectifier has poor power factor near the unity boosting ratio, the proposed PWM rectifier improves this problem. The mathmatical analysis are presented and experimental results are given.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.280-282
• /
• 1994

This paper proposes sliding mode state for robust speed control of induction motor. Sliding mode state observer is robust for measurement noise, modeling-error and load disturbance. The pole of sliding mode state observer can be placed at (0,0) in Z-plane for fast response. This method is, namely, deadbeat control. Sliding mode state observer output is discontinuous on a switching hyperplance, that causes harmful effects such as current harmonics and speed oscillation. In this paper, also the reducing method of the chattering of sliding mode state observer output is proposed. The proposed system is digitally implemented with TMS320C31.

• Proceedings of the KIEE Conference
• /
• 1997.07c
• /
• pp.1088-1090
• /
• 1997

This paper presents an effective methodology of optimal environmental and economic operation using evolution strategy. In power systems, evolution strategy, based on natural selection and genetics, can analyze non-linear and discontinuous functions in global search techniques. The formulation using this search techniques is multi-objective function, which consists of fuel cost and environmental effects concerning the pollution of the Earth's atmosphere caused by the emission of $SO_2$ and $NO_x$ from thermal generator plants. The proposed algorithms are applied on system with 6 generator.

• Proceedings of the KIEE Conference
• /
• 2004.10a
• /
• pp.98-100
• /
• 2004

This paper is proposed vibration minimize method of PMLSM which is designed to minimize detent force. To minimize of vibration at acceleration discontinuous point of velocity curve, genetic algorithm is applied. The vibration characteristic is compared general trapezoid velocity curve with proposed velocity profile.

• Journal of the Korean Ceramic Society
• /
• v.33 no.1
• /
• pp.74-82
• /
• 1996

Fe-Si based powders prepare by melting the metals in the composition of FeSi2,.Fe0.95Mn0.05Si2 and Fe0.95Co0.05Si0.2 were used as the starting materials together with a commercial FeSi2 powder to study the effect of oxidation on their thermoelectric properties. The powders were heated at 650~80$0^{\circ}C$ in dired air before forming and sintering at 1190 and 120$0^{\circ}C$ in Ar+7%H2. The microstructure and phases of the annealed specimens were observed using the optical microscopty SEM, EDS and XRD. The thermoelectric properties of the specimens were also measured. The temperature at which Seebe다 coefficient showed the maximum value increased with the degree of oxidation. Electrical conductivity showed a tendency to decrease in the oxidized samples regardless of their compositions. Seebeck coefficient of the specimen showed almost the same value even after oxidation which may be explained by the formation of the discontinuous second phases from impurities in the oxidized specimens.

• Journal of the Korean Ceramic Society
• /
• v.32 no.9
• /
• pp.1033-1039
• /
• 1995

The current experiment has quantitatively investigated the effect of the content of CaO and SiO2 on the microstructure, density, electrical resistivity, power loss and initial permeability of manganese zinc ferrites. The density increased initially with CaO and SiO2 content and the further addition showed an adverse effect. The excess addition of CaO and SiO2 developed a discontinuous grain growth with numerous pores inside grains and lowered the electrical resistivity. The initial permeability decreased with increasing the content of SiO2. The samples with relatively low power loss showed that half of the total loss at 10$0^{\circ}C$, 100 kHz and 2000 Gauss was due to the eddy current loss.

• Structural Engineering and Mechanics
• /
• v.3 no.5
• /
• pp.411-427
• /
• 1995

The most known continuum damage theories for brittle structures are suitable to model the degradation of the material due to the deformation process and the consequent initiation of a macro-crack. Nevertheless, they are not able to describe the propagation of the crack that leads, eventually, to the breakage of the structure into parts that undergo rigid body motion. This paper presents a theory, formulated from formal arguments of Continuum Mechanics, that may describe not only the degradation but also the fracture of elastic structures. The modeling of such a discontinuous phenomenon through a continuous theory is possible by taking a cohesion variable, related with the links between material points, as an additional degree of kinematical freedom. The possibilities of the proposed theory are discussed through examples.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.35 no.3
• /
• pp.210-216
• /
• 2012

Recently, it is not sufficient that contemporary firms satisfy customers to be really successful, they must create new value. To do so, many firms focus on the blue ocean strategy. The blue ocean strategy proposed the strategic canvas as a main tool for identifying the opportunities for value differentiation. It is easy to understand and for the use, but has weakness that is a unclear procedure to make it done. To complement its weak point, this study proposes a refined strategic canvas based on the concept of the business evolution that comes from a discontinuous evolution trend of 5 stages known as customer expectation.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1998.04a
• /
• pp.406-413
• /
• 1998

The distinct element method is improved to consider the charateristics of stress wave propagation in media involving the discontinuous faces. The distinct element method has many advantages to analyse the characteristics of the reflection, refraction and deflection of the waves in nonhomogeneous media. The double-suing connection system is adopted instead of the single-spring connection system because the distinct element cannot be used for analysing the contact behavior between the different materials by only one contact spring. For the verification of the improved code, the results of the numerical analysis are compared with that of the photoelastic experiments which are one or two dimensional wave propagation problem of the nonhomogeneous media including the different accoustic impendence material or voids. It is shown that the characteristics of the stress wave propagation in nonhomogeneous media can be simulated appropriately using the improved distinct element method.