• Tribology and Lubricants
• /
• v.22 no.4
• /
• pp.203-210
• /
• 2006

Two kinds of crankshaft oil supply system which were called continuous and discontinuous oil sup-ply system have recently been adopted in engine developing process. In order to clarify the lubrication characteristics for theses systems, in this paper, the comparison studies on supplied oil temperature, pressure, aspect ratio of bearings, and radial clearance were carried out for the main and the connecting rod bearing using computational fluid dynamic analysis.

• Journal of the Korean Mathematical Society
• /
• v.39 no.3
• /
• pp.363-376
• /
• 2002

Stability result is obtained for the approximation of the stationary Stokes problem with nonconforming elements proposed by Douglas et al [1] for the velocity and discontinuous piecewise constants for the pressure on qudrilateral elements. Optimal order $H^1$and $L^2$error estimates are derived.

• Journal of the Korean Mathematical Society
• /
• v.54 no.1
• /
• pp.249-265
• /
• 2017

Interface problem here refers to a second order elliptic problem with a discontinuous coefficient for the second order derivatives. For the corresponding boundary value problem, the maximum principle still holds but Hopf's boundary point lemma may fail. We will give an optimal power type estimate that replaces Hopf's lemma at those boundary points, where this coefficient jumps.

• Journal of the Korean Statistical Society
• /
• v.35 no.1
• /
• pp.1-23
• /
• 2006

In this paper we consider an estimation of the discontinuous variance function in nonparametric heteroscedastic random design regression model. We first propose estimators of the change point in the variance function and then construct an estimator of the entire variance function. We examine the rates of convergence of these estimators and give results for their asymptotics. Numerical work reveals that using the proposed change point analysis in the variance function estimation is quite effective.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.327-332
• /
• 1999

In this paper, six harmonic injection PWM method for reducing total harmonic distortion in single switch three phase discontinuous conduction mode boost converter is presented. In the proposed method, periodic six harmonic voltage is injected in the control circuit to vary the duty ratio of the converter switch within a line cycle so that the fifth order harmonic of the input current is reduced. Experimental results are verified by converter operating at 400V/6kW with three phase 140V~220V input.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.362-365
• /
• 1999

In this paper, the method of reducing harmonics and correcting of power factor in single PWM converter associated with diode rectifier and boos converter is studied. The ac-dc converter in which the harmonic distortion in the input current is reduced using a third harmonic injected PWM is proposed. A lower switching power loss and easy configuration o control circuit are obtained by adopting discontinuous current mode. Simulation and experimental results of ac-dc converter with 5[KHz] switching frequency are presented and correction of power factor and reduction of total harmonic distortion was established.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.626-630
• /
• 1999

A new integrated single-stage zero current switched(ZCS) quasi-resonant converter (QRC) for the power factor correction(PFC) converter is introduced in this paper. The power factor correction can be achieved by the discontinuous conduction mode(DCM) operation of an input current. The proposed converter has the characteristics of the good power factor, low line current harmonics, and tight output regulation. Furthermore, the ringing effect due to the output capacitance of the main switch can be eliminated by use of active clamp circuit.

• Journal of Electrical Engineering and information Science
• /
• v.3 no.1
• /
• pp.36-44
• /
• 1998

In this paper, a robust adaptive sliding mode control algorithm for accurate trajectory tracking of robot manipulators is proposed, with unknown parameters being estimated on-line. The controller is designed based on a Lyapunov method, which consists of adaptive feed-forward compensation part and a discontinuous control part. It is shown that, in the presence of the uncertainty and the disturbances arising from the actuator or some other causes, the tracking errors is bound to converge to zero asymptotically. An illustrative example is given to demonstrate the results of the propose method.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.933-934
• /
• 2008

This paper describes the process of extracting defect from optical photomask images. We introduce a new method of finding photomask detects with a single optical photomask damaged image. The proposed algorithm is efficient when an original undamaged image is unavailable. The experiment showed that even a small and discontinuous photomask defect was extracted as well as continuous type of defects.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.146.4-146
• /
• 2001

Various methods have been proposed for the time series prediction. Most of the conventional methods only optimize parameters of mathematical models, but to construct an appropriate functional form of the model is more difficult in the first place. We employ the Genetic Programming (GP) to construct the functional form of prediction models. Our method is distinguished because the model parameters are optimized by using Back-Propagation (BP)-like method and the prediction model includes discontinuous functions, such as if and max, as node functions for describing complicated phenomena. The above-mentioned functions are non-differentiable, but the BP method requires derivative. To solve this problem, we develop ...