• Geomechanics and Engineering
• /
• v.8 no.6
• /
• pp.757-767
• /
• 2015

Rock mass is an important engineering material. In hydropower engineering, rock mass of bank slope controlled the stability of an arch dam. However, mechanical characteristics of the rock mass are not only affected by lithology, but also joints. On the basis of field geological survey, this paper built rock mass material containing parallel concentrated joints with different dip angle, different number under different stress conditions by PFC (Particle Flow Code) numerical simulation. Next, we analyzed mechanical property and fracture features of this rock mass. The following achievements have been obtained through this research. (1) When dip angle of joints is $15^{\circ}$ and $30^{\circ}$, with the increase of joints number, peak strength of rock mass has not changed much. But when dip angle increase to $45^{\circ}$, especially increase to $60^{\circ}$ and $75^{\circ}$, peak strength of rock mass decreased obviously with the increase of joints number. (2) With the increase of confining stress, peak strengths of all rock mass have different degree of improvement, especially the rock mass with dip angle of $75^{\circ}$. (3) Under the condition of no confining stress, dip angle of joints is low and joint number is small, existence of joints has little influence on fracture mode of rock mass, but when joints number increase to 5, tensile deformation firstly happened at joints zone and further resulted in tension fracture of the whole rock mass. When dip angle of joints increases to $45^{\circ}$, fracture presented as shear along joints, and with increase of joints number, strength of rock mass is weakened caused by shear-tension fracture zone along joints. When dip angle of joints increases to $60^{\circ}$ and $75^{\circ}$, deformation and fracture model presented as tension fracture zone along concentrated joints. (4) Influence of increase of confining stress on fracture modes is to weaken joints' control function and to reduce the width of fracture zone. Furthermore, increase of confining stress translated deformation mode from tension to shear.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09b
• /
• pp.200-211
• /
• 2010

Tunnel Mapper, which is tunnel face survey system was used to conduct Face Mapping on the face of the tunnel that is under construction. Then, accuracy and utility value on the forecast of discontinuity were verified to verify the field application in order to present the measures for the use of the system for conducting research on the discontinuity. As result of the directivity verification following discontinuity‘s project, forecasted measurement and actually researched measurement error for the Dip direction and Dip angle was less than ${\pm}10$. Accuracy was 82.6% for Dip direction and 90.7% for Dip angle, which are high. Accordingly, face research discontinuity forecasting system's reliability level towards directivity is high. Tunnel Mapper, a tunnel face survey system can be leveraged to replace face's visual survey and to obtain objective information, enabling execution of the survey system that can automate face survey going beyond time and space related limitations.

• Geotechnical Engineering
• /
• v.14 no.2
• /
• pp.55-66
• /
• 1998

The purpose of this paper is to formulate and apply the stability analysis of toppling failure by considering the variation of discontinuity characteristics, slope geometry, and loading conditions. The stability condition on toppling failure of rock slope is mainly iuluenced by the dip angle $\alpha_B$ and H/t ratio. In order to check toppling failures in design, the stability charts composed of dip angle $\alpha_B$ versus H/t ratio have been constructed in the paper. In general, smaller dip angle $\alpha_B$ and smaller dip angle $\alpha_B$ and smaller H/T ratio give safer condition. The suggested curves change rapidly at the chitical point around the sone, H/t=4~6. The stable zone in stability charles becomes smaller due to step angle $\data$.

• ETRI Journal
• /
• v.27 no.3
• /
• pp.280-288
• /
• 2005

This paper presents an efficient algorithm for using the two-axis magnetic compass in portable devices. The general magnetic compass module consists of a three-axis magnetic compass and a two-axis inclinometer to calculate tilt-compensated azimuth information. In this paper, the tilt error is compensated using just a two-axis magnetic compass and two-axis accelerometer. The third-axis data of the magnetic compass is estimated using coordinate information that includes the extended dip angle and tilt information. The extended dip angle is estimated during the normalization process. This algorithm can be used to provide the tilt-compensated heading information to small portable devices such as navigation systems, PDAs, cell phones, and so on.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2001.04a
• /
• pp.108-119
• /
• 2001

The Spectral Analysis of surface Waves(SASW) Method has a great has a great potential for rapid determination of shear wave velocity profile of ground. However, it has an inherent limitation in the interpretation of test results due to the assumption that the ground is layered horizontally. The reason of the assumption is that difficulties exist in obtaining analytical solutions of wave equation when a soil system is composed of inclined soil layer. In this study, a finite-element method has been employed to assess the effects of dip angle and stiffness contrast of inclined soil layers and the testing direction on the dispersion curve. The propagation of wave front in the inclined soil layer was also investigated. The results indicated that the influence of dip angle on the dispersion curve is getting obvious as the dip angle increases and the propagation of wave front in the inclined layer also entirely different compared with the case of the horizontal layer.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.891-896
• /
• 2008

Behavior of the existing tunnel in the jointed rocks was affected by the adjacent slope excavation. In this study, large scale model tests were conducted. To investigate the tunnel distortion depending on the excavated slope angle and the joint dip of the ground performed model tests were numerically back analyzed. Consequently, as the joint dip and slope angle became larger, the tunnel distortion was tended to be larger. Ground displacement was also greatly dependent on the joint dip and the excavated slope angle, which indicated the possibility of the optimal slope reinforcement.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.5
• /
• pp.112-119
• /
• 2007

Under normal operating condition, the conductor of overhead transmission line could be always hold it's clearance within the safety margin that is specified in the line design guide of power company. Hence it may be very important to measure/or monitor the dip of the conductor, when building a new line, re-tensioning for an aged conductor, or monitoring dynamic line rating to maximize power capability. In this paper, we suggest a new method to estimate the dip and tension by catenary angle of the conductor. Since most conductors in overhead transmission lines show typical catenary curves, it can be uniquely determined the catenary curve for the conductor from the catenary angle at tower. Based on the catenary curve, the dip or horizontal tension can be easily estimated. Through some simulation and simple experimental results, it is verified that the suggested method can be effectively applied to measure/or monitor conductor dips and tensions in the overhead transmission lines.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.11 no.1
• /
• pp.1-9
• /
• 2009

When a rock slope is excavated adjacent to a existing tunnel, the behavior of the existing tunnel in the jointed rock masses is greatly influenced by the joint conditions and slope status. In this study, the effects of joint dip and slope angle close to a tunnel are investigated through a large scale model using a biaxial test equipment ($3.1\;m\;{\times}\;3.1\;m\;{\times}\;0.50\;m$ (width $\times$ height $\times$ length)). The jointed rock masses were built by concrete blocks. The diameter of the modeled tunnel is 0.6 m and the dip angles of joint vary in the range of $0-90^{\circ}$. In addition, the excavated slope angle varies within $30{\sim}90^{\circ}$. Deformational behaviors of the tunnel were analyzed in consideration of joint dip and slope angle. With increase of the joint dip and slope angle, the magnitude of tunnel distortion and the moment of tunnel lining were increased. Rock mass displacement in horizontal was also dependent on the joint dip and the excavated slope angle, which indicated the optimal slope reinforcement for a specific rock mass conditions.

• Geomechanics and Engineering
• /
• v.11 no.2
• /
• pp.269-288
• /
• 2016

The jointed rock mass behavior often plays a major role in the design of underground excavation, and their failures during excavation and in operation, are usually closely related to joints. This research attempts to evaluate the effects of two basic geometric factors influencing tunnel behavior in a jointed rock mass; joints spacing and joints orientation. A hybridized indirect boundary element code known as TFSDDM (Two-dimensional Fictitious Stress Displacement Discontinuity Method) is used to study the stress distribution around the tunnels excavated in jointed rock masses. This numerical analysis revealed that both the dip angle and spacing of joints have important influences on stress distribution on tunnel walls. For example the tensile and compressive tangential stresses at the boundary of the circular tunnel increase by reduction in the joint spacing, and by increase the dip joint angle the tensile stress in the tunnel roof decreases.

• Economic and Environmental Geology
• /
• v.31 no.6
• /
• pp.547-555
• /
• 1998

A new trigonometrical method for calculating total slip (T) of faulting is presented. The parameters for the calculations are used rake of fault striation, strike and dip of fault and of index planar structure such as bedding plane. The faults are groupped into three types. The direction of plunging of fault striation is out of a range ${\pm}90^{\circ}$ to the bedding dip direction in $360^{\circ}$ system, which is groupped into the type I. Meanwhile, the case of the direction lies in the above range can be separated into two different types, type II and type III, according to relative largeness of the angles rake of fault striation and i (see text). The type II has smaller rake than angle i and the type III has larger rake than angle i. Here I propose a few equations for calculating not only total slip (T) but strike slip (L) or dip slip (S) of the faulting. The equations are adapted selectively to the types of fault mentioned before. The limitation of the method is that the equations do not fit to polyphase faulting.