• Journal of Positioning, Navigation, and Timing
• /
• v.3 no.3
• /
• pp.91-97
• /
• 2014

A direct RF sampling method refers to a technique that directly converts a passband signal to an intermediate band or a baseband without using a mixer. This method is less complicated than an existing RF receiver because a mixer is not used. It uses digital processing after sampling, and thus can flexibly process signals in a number of bands using software. In this process, it is important to select an appropriate sampling frequency so that a number of signals can be converted to an intermediate band that is easy to process. In this study, going beyond previously studied direct RF sampling frequency selection methods, conditions that need to be additionally considered during receiver design were examined, and the structure of a direct RF sampling receiver that satisfies these conditions was suggested.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.9
• /
• pp.14-23
• /
• 2010

This paper reports the fabrication of a DVB-T/H System in Package (SiP) that is able to receive and process the DVB-T/H signal. The DVB-T/H is the European telecommunication standard for Digital Video Broadcasting (DVB). An IC-embedded Printed Circuit Board (PCB) process, interpose a chip between PCB layers, has applied to the DVB-T/H SiP. The chip inserted in DVB-T/H SiP is the System on Chip (SoC) for mobile TV. It is comprised of a RF block for DVB-T/H RF signal and a digital block to convert received signal to digital signal for an application processor. To operate the DVB-T/H IC, a 3MHz DC-DC converter and LDO are on the DVB-T/H SiP. And a 38.4MHz crystal is used as a clock source. The fabricated DVB-T/H SiP form 4 layers which size is $8mm{\times}8mm$. The DVB-T/H IC is located between 2nd and 3rd layer. According to the result of simulation, the RF signal sensitivity is improved since the layout modification of the ground plane and via. And we confirmed the adjustment of LC value on power transmission is necessary to turn down the noise level in a SiP. Although the size of a DVB-T/H SiP is decreased over 70% than reference module, the power consumption and efficiency is on a par with reference module. The average power consumption is 297mW and the efficiency is 87%. But, the RF signal sensitivity is declined by average 3.8dB. This is caused by the decrease of the RF signal sensitivity which is 2.8dB, because of the noise from the DC-DC converter.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2010.07a
• /
• pp.74-76
• /
• 2010

Digital images or videos are used in modern digital devices. The resolution of HDTV in digital broadcasting system is higher than that of previous analog systems. Also, mobile phone with 3G can provide images as well as video streaming services in realtime. In these circumstances, the visual quality of images has become an important factor. We can make image clear by transient improvement process that reduces transient in edges. In this paper, we present an transient improvement algorithm. The proposed algorithm improves edges by making smooth edge to steep edge. Before performing transient improvement algorithm, edge detection algorithm should be operated. Laplacian operator is used in edge detection, and the absolute value of it is used to calculate gain value. Then, local maximum and minimum values are computed to discriminate current pixel value to raise up or pull down. Compensating value that gain value multiplies with the difference between maximum (or minimum) value and current pixel value adds (or subtracts) to current pixel value. That is, improved signal is generated by making the narrow transient of edge. The advantage of proposed algorithm is that it doesn't produce shooting problem like overshoot or undershoot.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.8
• /
• pp.38-48
• /
• 2014

In this paper, a design of Signal Processing Analog Front-End IC for Automotive Piezo-Resistive Type Pressure Sensor is presented. In modern society, as the car turns to go from mechanical to electronic technology, the accuracy and reliability of electronic parts required importantly. In order to improve these points, Programmable Gain Amplifier (PGA) amplifies the received signal in accordance with gain for increasing the accuracy after PRT Sensor is operated to change physical pressure signals to electrical signals. The signal amplified from PGA is processed by Digital blocks like ADC, CMC and DAC. After going through this process, it is possible to determine the electrical signal to physical pressure signal. As processing analog signal to digital signal, reliability and accuracy in Analog Front-End IC is increased. The current consumption of IC is 5.32mA. The die area of the fabricated IC is $1.94mm{\times}1.94mm$.

• Journal of IKEEE
• /
• v.25 no.2
• /
• pp.302-308
• /
• 2021

A 12-bit 10-MS/s pipeline analog-to-digital converter (ADC) is proposed for image processing applications. The proposed pipeline ADC consists of a sample and hold amplifier, three stages, a 3-bit flash analog-to-digital converter, and a digital error corrector. Each stage is operated by using a 4-bit flash ADC (FADC) and a multiplying digital-to-analog converter (MDAC). The proposed sample and hold amplifier increases the voltage gain using gain boosting for the ADC with high resolution. The proposed pipelined ADC is designed using a 180-nm CMOS process with a supply voltage of 1.8 and it has an effective number of bit (ENOB) of 10.52 bits at sampling rate of 10MS/s for a 1-V_pp differential sinusoidal analog input with frequency of 1 MHz. The measured ENOB is 10.12 bits when the frequency of the sinusoidal analog input signal is a Nyquist frequency of approximately 5 MHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.3
• /
• pp.384-390
• /
• 2008

Chaotic OOK modulation method can be used in LDR(Low Data Rate) UWB systems. In this paper, UWB chaotic-OOK transmitter system is designed and verified using TSMC 0.18 um CMOS process. A transmitter system is composed of Quasi-chaotic signal generator, OOK Modulator, and driving amplifier. The traditional chaotic signal generators using analog feedback method is weak to process variation. In order to solve this problem, a quasi-chaotic signal generator using digital feedback technique is get wide band signal and OOK Modulator using T-type switching structure is used to enhance the isolation characteristic. A driving amplifier has differential to single structure to avoid an external balun for low cost communication. The measured output power spectrum of the transmitter meet the FCC regulation and the result of the modulation test at data rate of 20 Kbps, 200 Kbps, 2 Mbps, and 10 Mbps is conformed to LDR UWB system. It is shown that the transmitter in this paper can be used for the UWB chaotic-OOK system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.9C
• /
• pp.729-734
• /
• 2010

In the initial stage of the communications between a base station and a satellite transponder, the base station transmits the frequency-sweeping un-modulated up-link carrier within a certain frequency range to acquire the doppler frequency shift and signal power between the base station and the satellite in orbital flight. The satellite transponder acquires and tracks the carrier in order to initialize the communication. To control such initialization process, the satellite receiver should analyze the input carrier signal in various ways. This paper presents an SNR estimation algorithm to control the initialization process. The proposed algorithm converts the input signal into the baseband polar coordinate representation and estimates the SNR via the statistics of the angular signal components as well as the status parameters to control the receiver. The Monte-Carlo simulations shows the validity of the estimation proposed.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.9
• /
• pp.322-327
• /
• 2012

Parallel-plate-type scanning sensors have been commercially used for X-ray imaging sensors. In this study, we manufactured the scan typed 1D X-ray image sensor that can be used to obtain scanning images, by using the plasma display panel (PDP) fabrication process. We fabricated drift and pixel electrodes in the glass chamber and injected Xe gas at atmospheric pressure. We evaluated the intensity of a pixel signal depending on the bias voltage on the drift electrode and investigated the characteristics of shielding effect on the single pixel using lead (Pb). The adsorption rate of X-ray photon is low (4%) on the soda lime glass (1.1mm) and the electrical signal detected on the X-ray sensor was increased in the high bias voltage. We acquired digital X-ray scanning image with our DAS (data acquisition system) and sensor scanning system.

• Journal of Digital Convergence
• /
• v.13 no.10
• /
• pp.313-318
• /
• 2015

A traditional speech enhancement methods distort the sound spectrum generated according to estimation of the remaining noise, or invalid noise is a problem of lowering the speech recognition performance. In this paper, we propose a speech detection method that convergence the sound energy distribution process and sound energy parameters. The proposed method was used to receive properties reduce the influence of noise to maximize voice energy. In addition, the smaller value from the feature parameters of the speech signal The log energy features of the interval having a more of the log energy value relative to the region having a large energy similar to the log energy feature of the size of the voice signal containing the noise which reducing the mismatch of the training and the recognition environment recognition experiments Results confirmed that the improved recognition performance are checked compared to the conventional method. Car noise environment of Pause Hit Rate is in the 0dB and 5dB lower SNR region showed an accuracy of 97.1% and 97.3% in the high SNR region 10dB and 15dB 98.3%, showed an accuracy of 98.6%.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.6
• /
• pp.79-85
• /
• 2019

Recently, small radar require the development of small millimeter wave radar with high distance resolution to disable the target's system with a single strike. Small millimeter wave radar with high distance resolution need to process large amounts of data in real time to acquire and track target. In this paper, we summarized the real-time data preprocessing method to process the large amount of data required for small millimeter wave radar. In addition, the digital IF(Intermediate Frequency) receiver, Window processing, and, DFT(Discrete Fourier Transform) functions presented by real-time data preprocessing are implemented using FPGA(Field Programmable Gate Array). Finally the implemented real-time data preprocessing module was applied to the signal processor for small millimeter wave radar and verified by performance test related to the real-time preprocessing function.