• 오토저널
• /
• 제10권5호
• /
• pp.9-16
• /
• 1988

엔진 크랭크축계의 비틀림진동은 엔진설계 및 제작에 있어서 오랜동안 주관심사였다. 크랭크축계의 비틀림진동에서 고려되는 문제는 비틀림진동계의 고유진동수와 이에 따른 차수별 엔진의 공진속도와 엔진의 공진속도에서의 비틀림진동각 및 크랭크축의 비틀림진동에 의한 토오크와 비틀림 응력 등이다. 당사에서는 simulation program을 개발했으며, 비틀림 진동측정 방법도 개발했다. 또한 비틀림진동 측정결과와 simulation결과의 비교로부터 simulation결과 및 측정결과의 정확도를 높여가고 있으며, simulation 방법의 개선을 모색하고 있다. 본 글에서는 이 program에 이용된 기본이론과 실험방법 및 댐퍼 선정 방법을 간단히 소개하고자 한다.

• Tribology and Lubricants
• /
• 제22권6호
• /
• pp.342-349
• /
• 2006

In this study, a dynamic behavior of rotor-bearing system used in CNG compressor has been investigated using the combined methodologies of finite elements and transfer matrices. The finite element is formulated including the field element for a shaft section and the point element for roller bearings. The Houbolt method is used to consider the time march for the integration of the system equations. The transient whirl response of rotating shaft supported on roller bearings is obtained, considering compression forces and unbalance forces at eccentric crank-pin part. And, the steady state displacements of the rotor are compared with a variation in stiffness coefficient of roller bearings. Results show that the loci of crankshaft considering unbalance forces and external compression forces are more severe in whirl motion than with only unbalance forces.

• 한국소음진동공학회논문집
• /
• 제24권6호
• /
• pp.452-461
• /
• 2014

Two stroke low speed diesel engines that have many advantages such as high thermal efficiency and durability have been widely used for marine engine. However, it is also true that many problems have occurred due to the high explosion pressure and severe operating environment. Especially problems of shaft damage etc. intensively occurred due to the phenomenon of crankshaft exceeding the allowable stress, including the shaft vibration of the engine model in the early stage. In this study, the crankshaft fracture phenomenon of early engine model was evaluated and analyzed by using up-to-date torsional vibration calculation program and measurement instrument. And this was numerically shown.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.448-452
• /
• 2008

2-stroke marine diesel engine has generally one exhaust valve and three fuel injection nozzle which are key component for engine's performance and combustion. Fuel injection and exhaust valve driving system are driven by rotating of camshaft. Rotation of crank shaft drives the cam shaft through gear train that is composed of $3{\sim}4$ gear wheels. Gear column supporting the gear wheel has to bear against the dynamics forces by engine running as well as gearing forces. In this paper, structural analysis for engine structure and fatigue strength assessment of welded joint is shown. Repeatedly full cyclic simulation during one cycle is performed to investigate the structural behavior of engine. Fatigue analysis is carried out based on IIW using submodeling technique to obtain more detailed stress distribution.

• 제어로봇시스템학회논문지
• /
• 제17권1호
• /
• pp.1-5
• /
• 2011

The basic signals for electronic engine control are velocity and degree of the engine cam shaft. The CPS sensor used for this signal and magnetic pick-up type CPS sensor is more popular. It is very important thing analyze this signal correctly. If there are some mistakes at the analysis, like a noise, The engine do not working at the best status, it will generate some noise, emit exhaust fumes and waste more gases. In general way to analysis this signal, you use zero-level detector circuit and in order to reduce the error you must use another sensor like a TDC sensor. In this paper, We proposed the analysis method using electronics circuits for magnetic pick-up type CPS sensor. We designed Comparison level detector circuit, Differential circuit and Full-rectifier circuit for detected the Long tooth and Short tooth level correctly without another sensor. We expected it is useful for more reliable engine control.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 전기학술대회논문집
• /
• pp.160-165
• /
• 2005

The proceeding bearings of marine diesel engine are affected by dynamic loads from the cylinder gas pressure and the inertia force from the crank mechanism. Oil film must support the load of the shaft and it also must protect the proceeding and the bearings from damage. This study uses Goenka's new curve fit to carry out the theoretical analysis of oil film in proceeding bearings for MAN B&W 12K90MC-C and Hyundai Heavy Industry Co., Ltd HiMSEN H21/32 Engine. The applied engine's analysis results show the behavior of the proceedings in main and crank pin bearings. The results of this study will be the proper criteria for the proceeding bearings design and be available for development of the new technology in the proceeding bearing and for the high strength lining coating.

• Journal of Advanced Marine Engineering and Technology
• /
• 제35권4호
• /
• pp.436-442
• /
• 2011

기관의 정확한 출력을 얻기 위해서는 실린더내 압력의 정확한 측정이 기본적으로 중요하다. 그러나 MIPS같은 전자식지압기로 계측된 지시마력(IHP)과 기계식 지압기에 의해 산출된 지시마력 사이에는 상당한 차이를 보인다. 이러한 차이는 선박용 디젤엔진에서 TDC위치가 부정확하기 때문으로 확인되었다. 본 논문에서는 TDC위치에 대한 크랭크 각의 부정확한 정도를 선박용 M/E과 G/E에 대하여 각각 연구하였다. 또한 실린더 압력을 '시간기준'과 '크랭크각도기준'의 두 가지 방법으로 수집하여 검토하였다. 크랭크각도기준은 크랭크축에 장착된 엔코더로부터 실제 각도에 의한 수집방법이며, 시간기준은 엔코더의 Z펄스로 검출된 회전수에 의해 계산된 각도에 의한 수집방법이다. 시간기준 방법은 MIPS의 데이터 수집과 같은 방법이다. 시간기준 수집방법은 순간속도 변동과 부하변동의 영향으로 선박 엔진(M/E와 G/E)의 성능분석에는 적합하지 않음을 분명히 하였다. 또한, 각도기준 방법에 있어서도 M/E의 경우에는 부하변동에 의한 속도변동이 정확한 출력산정을 어렵게 하는 요인임을 확인하였다.

• 해양환경안전학회지
• /
• 제26권4호
• /
• pp.429-435
• /
• 2020

엔진의 출력을 측정하기 위한 방법은 실린더의 연소압력을 측정하여 지시마력을 구하는 방법과 축토크를 측정하여 축마력을 구하는 방법이 있다. 축토크로 실린더의 상태를 확인하기에는 한계가 있으며, 엔진의 성능 측정과 실린더의 연소 해석을 위해서는 실린더의 연소 상태를 확인할 수 있는 연소압력을 측정하는 방법이 가장 정확하다. 측정에 있어 연소압력은 크랭크샤프트 회전 각도에 따른 실린더 압력이 도시되어야하기 때문에 정확한 실린더 앵글각도를 정확히 인지시키는 작업이 가장 중요하다. 본 연구에서는 실제 운항선의 발전기 엔진을 대상으로 실린더 압력을 측정하기 위하여 크랭크 앵글 센서로 엔코더를 사용하였고 엔코더에서 인지하는 TDC(TDC_encoder)와 압축압력에 의한 TDC(TDC_comp) 간의 실측을 통하여 차이가 발생하는 원인에 대하여 고찰하였다. 또한 0 %, 25 %, 50 %와 60 % 부하에서 측정된 실린더의 TDC_comp와 TDC_encoder 간의 차이를 통하여 크랭크샤프트의 제작에 의한 영향, 부하증가에 따른 엔진과 발전기 사이의 커플링 영향에 대한 결과를 고찰하였으며, 발전기의 부하가 증가할수록 최대 3°CA까지 TDC의 오차가 발생함을 확인하였다.

• 한국시뮬레이션학회논문지
• /
• 제12권3호
• /
• pp.41-53
• /
• 2003

The major components of an engine are engine block (or cylinder block), cylinder head, crank shaft, connecting rod and cam shaft. Thus the engine shop usually consists of six sub-lines, five machining lines and one assembly line. Flow line is the typical concept of layout for machining these parts, especially for engine block. In order to design an engine block machining line, several factors should be considered such as yearly production target, working hours, machines, tools, material handling equipments and so on. If the designers of manufacturing line were unaware of some factors those would be influenced on the system performance, it would make greater problems in the phase of mass production. Therefore the initial design of engine block machining line should be verified carefully. Simulation is the most powerful tool for analyzing the initial layout. This paper introduces the major factors those should be considered for designing the machining line and their effects on the system performance. 3D simulation models are developed with QUEST. Using the simulation model developed the initial layout is analyzed, and we suggest some ideas for improvement.

• 전기학회논문지
• /
• 제57권6호
• /
• pp.966-971
• /
• 2008

Free-piston engine system is a new type energy converter which uses a linear motion of piston by using linear generator. In free-piston engine system, the piston is not connected to a crank-shaft. The major advantages of free-piston engine system are high efficiency and low mechanical loss from the absence of motion conversion devices. Linear generator of free-piston engine system is used as generator and starting motor. In design step, considering of back-emf and detent force characteristics for generating mode and thrust and control characteristics for starting mode is needed. In this research, generating mode of flat-type linear generator and tubular-type linear generator is analyzed by finite element analysis method and starting mode of both type linear generators is analyzed by using capability curve. Capability curve is plotted from electrical parameters of both type linear generator and motion profile is calculated from mechanical parameters.