• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.126-126
• /
• 2012

In past decades, the themal inkjet (TIJ) printer has been widely used as one of the most well-known digital printing technology due to its low cost, and high printing quality. Since the printing speed of TIJ printers are much slower than that of laser printers, however, there has been intensive efforts to raise the printing speed of TIJ printers. One of the most plausible methods to raise the printing speed of TIJ printers is to adopt a page-wide array TIJ printhead. To accomplish this goal, the high efficiency inkjet heating resistor films should be developed to settle the high power consumption problem of a page-wide array TIJ printhead. In this study, we investigated noble metal based multicomponent thin film resistor films prepared by atomic layer deposition (ALD) for a high efficiency inkjet printhead. Design concept, preparation, material properties of noble metal based multicomponent thin films will be discussed in terms of mutlfunctionality.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2002년도 학술대회 논문집
• /
• pp.322-325
• /
• 2002

In this paper, the power-linking device connecting the high-Tc super-conducting(HTS) coil to the power system in the DC reactor type three-phase high-Tc superconducting fault current limiter (SFCL) has been designed. This design was triggered from the concept that the magnetic energy could be exchanged into the electrical energy each other. Ferromagnetic material is used as the path of magnetic flux. The device mentioned above was named Magnetic Core Reactor(MCR). MCR was designed to minimize the voltage drop caused by copper loss. The current density of the conductor was 1.3 A/mm$^2$ and % voltage drop was 2%.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 춘계전력전자학술대회 논문집(1)
• /
• pp.243-246
• /
• 2003

This paper presents a new motor design well suited for an advanced exercise bike. The advanced exercise bike setup high demands for performance and physical dimensions, which is high torque, wide speed range and a diameter/length ratio around 5. These requirements makes the new motor design called an E-core Transverse Flu Machine (ETFM) vev interesting because the segmented design of the stator and rotor poles enables high diameter without increasing the flux-path and since the ETFM is similar to the switched reluctance motor, high torque and wide speed range is possible. The design of the ETFM can be peformed using a developed design program, which is also introduced in the paper. A prototype of the exercise bike with the ETFM and a classical H-bridge converter with analog current control is constructed for verification of the concept.

• Journal of Information Technology Applications and Management
• /
• 제16권2호
• /
• pp.99-120
• /
• 2009

The relationship between the performance measures and the acceptance of evaluation has been of importance not only in the academic field but in the business area. However, there had not been many studies on the factors which affect the goal core, that is, specificity and difficulty. The previous literature on the evaluation of measures has limitations in that the common and unique measures without suggesting the concept of shared measures are used. Thus, the purpose of this study is to examine the effects of the environmental characteristics of the goal setting on the result and acceptance of the evaluation, which is mediated by the characteristics of the goal core. This study further tests if there are any moderating effects from using the shared measures of performance.

• Journal of Electrical Engineering and Technology
• /
• 제6권1호
• /
• pp.81-85
• /
• 2011

The end effect of a linear induction motor (LIM) has been known for several decades, especially in high speed operation. The exit part of the primary is not dealt as extensively as the entry part because of its minor effect. However, the exit part is one of the keys to weaken the dolphin effect, which occurs in high speed operation. In this paper, the concept of the virtual primary core is introduced, and chamfering of the primary outlet teeth is proposed to minimize the longitudinal end effect at the exit zone. For this, LIM for the high-speed train is designed and analyzed by using finite element method. Results confirm that chamfering can improve thrust performance effectively.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 1998년도 유체기계 연구개발 발표회 논문집
• /
• pp.33-41
• /
• 1998

In this study, the performance prediction programs for centrifugal pumps are developed. To estimate the losses in the centrifugal pump impellers, two-zone model and TEIS(two elements in series) model are applied to the program. The basic concept of two zone model considers the primary zone that is an isentropic core flow and the secondary zone that is non-isentropic region at the impeller exit. The flows through two different zones mixed out at the impeller exit and the mixing process occurs with an increase in entropy, a decrease in total pressure. The level of the core flow diffusion in a impeller was calculated using TEIS(two elements in series) model. The effects of various parameters which are used in this program on the prediction of head and efficiency are discussed. The correlation curves to select the effectiveness of the primitive TEIS model were suggested according to the specific speed of the centrifugal pumps.

• 한국항행학회논문지
• /
• 제14권1호
• /
• pp.57-65
• /
• 2010

본 연구에서는 새로운 형태의 로봇 제어기의 구조인 이기종 멀티프로세서 제어기의 개념적인 구조를 제시하며, 제어기 내에 분산된 멀티프로세서들을 sRIO 통신을 이용하여 통합하는 구조적인 방법을 소개한다. 또한 sRIO 통신으로 통합된 이기종 멀티프로세서의 구현을 위한 방법으로 FPGA 내에 설계된 sRIO IP Core를 활용한 시뮬레이션을 수행하고 그 결과를 확인하였다.

• 시스템엔지니어링학술지
• /
• 제7권1호
• /
• pp.43-51
• /
• 2011

SE generally defines approaching ways of conducting identification, verification and integration of an optimized product and process solution to meet customer's needs by leveraging organizational competency in engineering and management. To successfully develop a new product under mass production contract, it is important to efficiently carry out the program by ensuring that three major competencies are secured; core technology, system integration, and program management. For successful implementation of tasks in the three areas, systematic execution is called for, which requires identifying risk factors in advance. In particular, comprehensive risk management role and responsibility is required for program management. Success of a development program is determined by complex elements of human resources, organization culture, and overall competency of an organization in technology and program management, including capability of the program manager. In this paper, a risk management solution is suggested to lead a program to success with a more efficient way through actual risk management by the concept of SE around the above three areas.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 2008년도 한국우주과학회보 제17권2호
• /
• pp.37.4-38
• /
• 2008

Recently, statement of Intent for ILN has been signed by 9 countries including Korea, initiated March of this year by NASA which invited countries having lunar exploration plans. Concept of ILN is placing several core set of instrumentation on the Moon, in order to maximize scientific return to all of the participants. Network measurements from various nodes on lunar surface is essential for understanding internal structure of the Moon and environment around the Moon. Currently, Core Instrument Working Group is discussing the scientific interests and instrumentation among participated countries. Korea also is looking over various ways to participate ILN. We will introduce the progress and possible lunar science of ILN and will discuss the science mission objectives.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.98-100
• /
• 2005

This paper, proposes concept of personal robot middleware core also called streaming layer. Based on openness and portability, the streaming layer is proposed in order to meet requirements of different kinds of applications. The streaming layer architecture provides effective management of data flows and allows integration of different systems with ease regardless software of hardware platform. With extensibility support additional features can be build in without affect to performance. Therefore, heterogeneous network support, real-time communications, embedded boards support can be easily achieved. In order to achieve high performance together with portability into different platforms, the most functions has to be implemented in C language, while critical parts, such as scheduling, priority assignment has to be made using native functions of tested platforms.