• Bulletin of the Korean Chemical Society
• /
• v.32 no.1
• /
• pp.157-161
• /
• 2011

For the fabrication of multifunctional biopolymer nanocomposites in the combination of carbon nanotubes (CNTs), recently increasing attention has been paid to an effective homogenization of CNTs within polymer matrices and a fine tuning of the concentration. We developed an efficient method to produce homogeneous CNT-polycaprolactone nanocomposites with various and controllable CNT concentrations using an ionically-modified multi-walled CNT, MWCNT-Cl. The modified MWCNTs could be homogeneously dispersed in tetrahydrofuran (THF). Polycaprolactone (PCL) as a biodegradable and biocompatible polymer was smoothly dissolved in the homogeneous MWCNT-Cl/THF solution without agglomeration of MWCNT-Cl. The physicochemical and mechanical properties of the resultant nanocomposites were examined and the biological usefulness was briefly assessed.

• Proceedings of the KIPE Conference
• /
• 2018.07a
• /
• pp.434-435
• /
• 2018

In this paper, a single-phase single-stage three-level AC/DC converter with a wide controllable output voltage is presented. It integrates a PFC converter and a three level DC/DC converter into one. The proposed converter operates at a fixed frequency and provides a wide controllable output voltage ($200V_{dc}-430V_{dc}$) with high efficiencies over a wide load range. In addition, the input boost inductors operate in a discontinuous mode to improve the input power factor. Moreover, all the switching devices operate with ZVS, and the converter's THD is small especially at full load. The feasibility of the proposed converter is verified with experimental results of a 1.5kW prototype.

• KIEE International Transactions on Power Engineering
• /
• v.4A no.2
• /
• pp.51-57
• /
• 2004

This paper describes the dynamic performance of a variable speed wind turbine system responding to a wide variety of wind variations. Modeling of the wind generation using power electronics interface is proposed for dynamic simulation analysis. Component models and equations are addressed and their incorporations into a transient analysis program, PSCAD/EMTDC are provided. A wind model of four components is described, which enables observing dynamic behaviors of the wind turbine resulting from wind variations. Controllable power inverter strategies are intended for capturing the maximum power under variable speed operation and maintaining reactive power generation at a pre-determined level for constant power factor control or voltage regulation control. The components and control schemes are modeled by user-defined functions. Simulation case studies provide variable speed wind generator dynamic performance for changes in wind speed

• Smart Structures and Systems
• /
• v.2 no.1
• /
• pp.61-80
• /
• 2006

The concept of structural vibration control is to absorb vibration energy of the structure by introducing auxiliary devices. Various types of structural vibration control theories and devices have been recently developed and introduced into mechanical systems. One of such devices is damper employing controllable fluids such as ElectroRheological (ER) or MagnetoRheological (MR) fluids. MagnetoRheological (MR) materials are suspensions of fine magnetizable ferromagnetic particles in a non-magnetic medium exhibiting controllable rheological behaviour in the presence of an applied magnetic field. This paper presents the modelling of an MRfluid damper. The damper model is developed based on Newtonian shear flow and Bingham plastic shear flow models. The geometric parameters are varied to get the optimised damper characteristics. The numerical analysis is carried out to estimate the damping coefficient and damping force. The analytical results are compared with the experimental results. The results confirm that MR damper is one of the most promising new semi-active devices for structural vibration control.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.33 no.2
• /
• pp.97-104
• /
• 2010

Using the known result of the expected busy period for the triadic Min (N, T, D) operating policy applied to a controllable M/G/1 queueing model, its upper and lower bounds are derived to approximate its corresponding actual value. Both bounds are represented in terms of the expected busy periods for the dyadic Min (N, T), Min (N, D) and Min (T, D) and simple N, T and D operating policies. All three input variables N, T and D are equally contributed to construct such bounds for better approximations.

• The Journal of the Acoustical Society of Korea
• /
• v.26 no.1E
• /
• pp.27-32
• /
• 2007

Hydraulic actuator and electro-magnetic liner actuator have been used as typical active vibration control methods. However these methods have many kinds of disadvantages such as causing space limit, difficult maintenance, complicate structures, etc. The purpose of this paper was to study on the possibility of active vibration control using piezoelectric transducer. Piezoelectric transducer generated a vibration and GIC (General Impedance Converter) amplifier was adopted to give adjustable vibration signal to transducer and high amplitude of vibration. Resonance frequency of piezoelectric transducer was controlled by GIC amplifier and higher amplitude of vibration was achieved. Finally active vibration control using piezoelectric transducer was performed.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.21 no.46
• /
• pp.73-91
• /
• 1998

The ratio of Industrial Accident in Korea has been inclined to decrease for recent ten years since industrialization beginnings of Korea. But it is still in high level viewed from international comparison. Up to now, we depended on classical method Accident as the phenomenical and inductive result. And we searched for the counter plan in the basis of the result by this method. But, in this research, we analyzed the distinctions which the structure of the occurrence of Industrial Accident using new model in order to approach the cause of Industrial accident of Korea more basically. In this new model, I am going to arrange the controllable variables in the factors of Industrial Accident and to analyze the effect of these controllable variables in the structure of Industrial Accident.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.31 no.4
• /
• pp.86-92
• /
• 2008

The expected busy period for the controllable M/G/1 queueing model operating under the triadic Max (N, T, D) policy is derived by using a new concept so called "the pseudo probability density function." In order to justify the proposed approaches for the triadic policy, well-known expected busy periods for the dyadic policies are recovered from the obtained result as special cases.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.1
• /
• pp.21-26
• /
• 2006

In this paper, to improve the variable and remote controllable digital power-supply design. It is able to RS-232 communication for remote control. And it can also observe the correct power. Finally, it intend to high ratio design that compare input power with output power. There are especially useful solution in korea to be under the unstable voltage environment.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.53 no.3
• /
• pp.188-196
• /
• 2004

Amplifier linearity plays a major role in the quality of mordern communication systems. The Power amplifier should be operated near saturation region to achieve high efficiency But at this region amplitude and phase distortions of the amplifier remarkably increase with the input power increase and cause a significant adjacent channel interference. In this paper, an independently controllable AM/AM and AM/PM predistortion linearizers consisted of two bias feed resistance linearizers is proposed. This linearizer allows independent adjustment of the AM/AM and AM/PM curves by using two adjustable voltages to compensate tile power amplifier non-linearities. The predistortion linearizer can improve the ACPR by 5.3dB with cdma2000 multi carrier signals. And by applying this linearizer to two-tone(880MHz) power amplifier, third order IMD products are improved up to 8(dB).