• 한국항행학회논문지
• /
• 제10권3호
• /
• pp.198-204
• /
• 2006

본 논문에서는 스트립 폭과 격자주기, 유전체 층의 비유전율과 두께, 그리고 TE(transverse electric) 평면파의 입사각에 따른 접지된 유전체 평면위의 저항띠 격자구조에 의한 TE 산란 문제를 수치해석 방법인 FGMM(Fourier-Galerkin Moment Method)를 이용하여 해석하였다. 유도되는 표면전류밀도는 간단한 함수인 지수 함수를 사용하여 Fourier 급수로 전개하였다. 유전체층의 비유전율과 두께가 증가함에 따라 반사전력이 증가하였고, 반사전력의 급변점들은 공진효과에 기인한 것으로 과거에 wood's anomallies[7]라고 불리워졌다. 제안된 방법의 검증을 위하여 기존의 완전도체 경우인 균일 저항율 R = 0에 대한 정규화된 반사전력의 수치결과는 기존의 논문들과 일치하였다.

• 한국표면공학회지
• /
• 제47권5호
• /
• pp.239-243
• /
• 2014

The electrical and optical properties of amorphous In-Tin-Zinc-Oxide(ITZO) deposited at room temperature using rf-magnetron sputtering were investigated. The amorphous ITZO thin films were obtained at the composition of In:Sn:Zn = 6:2:2, 4:3:3, and 2:4:4, but the ITZO (8:1:1) showed a crystalline phase of bixbyite structure of In2O3. The resistivity of ITZO could be controlled by oxygen pressure in the sputtering ambient. The resistivity of post-annealed ITZO thin films exhibited the dependence on the amount of Indium. Optical energy band gap and transmittance increased as the amount of indium in ITZO increased. For the device application with ITZO, the bottom-gated thin-film transistor using ITZO as a active channel layer was fabricated. It showed a threshold voltage of 1.42V and an on/off ratio of $5.63{\times}10^7$ operated with saturation field-effect mobility of $14.2cm^2/V{\cdot}s$.

• 한국광학회지
• /
• 제19권4호
• /
• pp.249-254
• /
• 2008

새 구조의 액정 엑스선 감지기를 만들었다. 이것은 액정판을 만들고 유리판을 얇게 식각한 다음, 그 유리판 위에 반사막과 광전도층을 연속하여 입힌 구조이다. 새 구조의 액정엑스선 감지기는 공정의 안정성, 대면적화, 감도 등에서 이미 상품화된 엑스선 감지기와도 충분히 경쟁할 수 있으며, 따라서 성공적으로 상용화 할 수 있음을 확인했다.

• 반도체디스플레이기술학회지
• /
• 제17권2호
• /
• pp.1-5
• /
• 2018

Elastic resistive pressure sensor is fabricated by a direct spray coating of silver nanowires (AgNWs) on uncured polydimethylsiloxane (PDMS) and an additional coating of a conductive polymer, poly(3,4-ethylenedioxythiophene): poly (styrene sulfonate) (PEDOT:PSS). To improve the sensitive and stability, we have fabricated sandwich-structured AgNW/polymer sensor where two AgNW/polymer-coated PDMS films are laminated with the conducting surfaces contacted by pressure lamination. It shows a resistance decrease upon loading due to the formation of dense network of AgNWs. It is demonstrated that the sandwich-structured AgNW/polymer sensor exhibits very high sensitivity ($2.59kPa^{-1}$) and gauge factor (37.8) in the low pressure regime. It can also detect a subtle placement and removal of a weight as low as 3.4 mg, the corresponding pressure of which is about 5.4 Pa. It is shown that the protrusion of AgNWs from PDMS is suppressed substantially by the over-coated PEDOT:PSS layer, thereby reducing hysteresis and rendering the sensor more stable.

• Journal of Electrochemical Science and Technology
• /
• 제10권3호
• /
• pp.335-343
• /
• 2019

In this study, $Sr_2Ni_{1.8}Mo_{0.2}O_{6-{\delta}}$ (SNM) with a double perovskite structure was investigated as an alternative anode for use in the $CH_4$ fuel in solid oxide fuel cells. SNM demonstrates a double perovskite phase over $600^{\circ}C$ and marginal crystallization at higher temperatures. The Ni nanoparticles were exsolved from the SNM anode during the fabrication process. As the SNM anode demonstrates poor electrochemical and electro-catalytic properties in the $H_2$ and $CH_4$ fuels, it was modified by applying a samarium-doped ceria (SDC) coating on its surface to improve the cell performance. As a result of this SDC modification, the cell performance improved from $39.4mW/cm^2$ to $117.7mW/cm^2$ in $H_2$ and from $15.9mW/cm^2$ to $66.6mW/cm^2$ in $CH_4$ at $850^{\circ}C$. The mixed ionic and electronic conductive property of the SDC provided electrochemical oxidation sites that are beyond the triple boundary phase sites in the SNM anode. In addition, the carbon deposition on the SDC thin layer was minimized due to the SDC's excellent oxygen ion conductivity.

• 한국융합학회논문지
• /
• 제12권1호
• /
• pp.193-198
• /
• 2021

본 연구에서는 초고압(Extra High Voltage) 케이블의 방식층(Oversheath)에 사용되는 반도전성 난연컴파운드의 보다 우수한 내충격성 및 전기적 특성을 만족할 수 있는 나노융복합 소재기술에 대해 연구하였다. 반도전성 난연컴파운드에 사용되는 도전성 카본블랙 일부를 CNT(carbon nano tube)로 대체하였으며, 이때 물성변화를 분석하였다. 전기적 특성이 현격하게 뛰어난 탄소나노튜브의 적용을 통해 소량의 전도성필러 처방으로도 보다 우수한 전기적 특성을 부여할 수 있게 된다. 또한, 컴파운드 기준 전체 필러량이 감량됨에 따라서 가공성이 향상되며, 특히 유연성 및 내충격성이 향상되기 때문에 케이블의 내구성 향상에 기여할 것으로 기대된다.

• 한국재료학회지
• /
• 제31권3호
• /
• pp.115-121
• /
• 2021

MnO2 can be potentially utilized as an electrode material for redox capacitors. The deposition of MnO2 with poor electrical conductivity onto porous carbons supplies them with additional conductive paths; as a result, the capacitance of the electrical double layer formed on the porous carbon surface can be utilized together with the redox capacitance of MnO2. However, the obtained composites are not generally suitable for industrial production because they require the use of expensive porous carbons and/or inefficient fabrication methods. Thus, to develop an effective preparation procedure of the composite, a suitable structure of porous carbons must be determined. In this study, MnO2/C composites have been prepared from activated carbon gels with various pore sizes, and their electrical properties are investigated via cyclic voltammetry. In particular, mesoporous carbons with a pore size of around 20 nm form a composite with a relatively low capacitance (98 F/g-composite) and poor rate performance despite the moderate redox capacitance obtained for MnO2 (313 F/g-MnO2). On the other hand, using macro-porous carbons with a pore size of around 60 nm increases the MnO2 redox capacitance (399 F/g-MnO2) as well as the capacitance and rate performance of the entire material (203 F/g-composite). The obtained results can be used in the industrial manufacturing of MnO2/C composites for supercapacitor electrodes from the commercially available porous carbons.

• 멤브레인
• /
• 제33권5호
• /
• pp.248-256
• /
• 2023

ITO 투명 전극 필름은 디스플레이, 전기 자동차 등 산업 전 범위에서 널리 사용되는 전자 재료이다. 본 연구에서는 이러한 indium tin oxide (ITO) 필름의 열성형 안정성을 향상시키기 위하여 Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) 전도성 고분자 코팅 용액 조성을 결정하였다. 1000 S/cm의 고 전도성을 보이는 PEDOT:PSS 용액에 끓는점이 각기 다른 4가지 종류의 용매를 희석하였고, 코팅 전 후 면저항 변화를 분석하였다. 또한 380~800 nm 영역의 광 투과율 분석 및 Raman 스펙트럼 분석을 통하여 PEDOT:PSS 박막이 코팅된 ITO 투명 전극의 전기적 특성 결정 메커니즘을 규명하였다. 230℃ 열성형 공정 결과 ITO 필름은 113% 연신 상태에서 이미 전기 전도성을 읽었지만, ethylene glycol을 희석 용매로 사용하여 얻어진 전도성 고분자 박막이 적용된 ITO 필름은 126% 고 연신 상태에서도 초기 60 Ω/sq 면저항을 246 Ω/sq로 유지하는 우수한 전기 전도성을 보였다.

• 한국군사과학기술학회지
• /
• 제27권3호
• /
• pp.311-318
• /
• 2024

In this paper, a design for a radio frequency(RF) and infrared(IR) absorber with metasurfaces is discussed in microwave frequency bands. The RF absorber includes double layers of metasurfaces to operate in S- and X-bands. Effects of sheet resistance of the metasurfaces and thicknesses of dielectric supporting layers on reflection responses are investigated. An IR stealth layer incorporates an array of conductive grids with slits to reflect IR signals but to transmit RF signals and visible rays. Periodicity of the grids and slits is studied for transmission responses in the X-band and a surface area ratio. Reflection responses of the RF/IR multispectral absorber are found to be lower than -10 dB and -16 dB in the S- and X-bands, respectively, from full-wave simulation. Finally, the RF/IR multispectral absorber is fabricated and its reflection responses are measured to verify designed performance.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.434-434
• /
• 2012

Despite recent efforts for fabricating flexible transparent conducting films (TCFs) with low resistance and high transmittance, several obstacles to meet the requirement of flexible displays still remain. Indium tin oxide (ITO) thin films, which have been traditionally used as the TCFs, have a serious obstacle in TCFs applications. SWNTs are the most appropriate materials for conductive films for displays due to their excellent high mechanical strength and electrical conductivity. Recently, it has been demonstrated that acid treatment is an efficient method for surfactant removal. However, the treatment has been reported to destroy most SWNT. In this work, the fabrication by the spraying process of transparent SWNT films and reduction of its sheet resistance by Au-ionic doping treatment on PET substrates is researched. Arc-discharge SWNTs were dispersed in deionized water by adding sodium dodecyl sulfate (SDS) as surfactant and sonicated, followed by the centrifugation. The dispersed SWNT was spray-coated on PET substrate and dried on a hotplate. When the spray process was terminated, the TCF was immersed into deionized water to remove the surfactant and then it was dried on hotplate. The TCF film was then was doped with Au-ionic doping treatment, rinsed with deionized water and dried. The surface morphology of TCF was characterized by field emission scanning electron microscopy. The sheet resistance and optical transmission properties of the TCF were measured with a four-point probe method and a UV-visible spectrometry, respectively. This was confirmed and discussed on the XPS and UPS studies. We show that 87 ${\Omega}/{\Box}$ sheet resistances with 81% transmittance at the wavelength of 550 nm. The changes in electrical and optical conductivity of SWNT film before and after Au-ionic doping treatments were discussed. The effects of hole transport interface layer using Au-ionic doping SWNT on the performance of organic solar cells were investigated.