• Korea-Australia Rheology Journal
• /
• 제20권3호
• /
• pp.109-116
• /
• 2008

The effect of intermolecular aggregation induced by hydrophobic and electrostatic interactions on shear and elongational flow properties of aqueous acrylic thickener solutions is discussed. Complex shear modulus is determined at frequencies up to $10^4$ rad/s employing oscillatory squeeze flow. Extensional flow behavior is characterized using Capillary Break-up Extensional Rheometry. Aqueous solutions of poly(acrylic acid)(PAA)/poly(vinylpyrrolidone-co-vinylimidazole) (PVP-VI) mixtures exhibit unusual rheological properties described here for the first time. Zero-shear viscosity of the mixtures increases with decreasing pH and can exceed that of the pure polymers in solution by more than two orders of magnitude. This is attributed to the formation of complexes induced by electrostatic interactions in the pH range, where both polymers are oppositely charged. PAA/PVP-VI mixtures are compared to the commercial thickener Sterocoll FD (BASF SE), which is a statistical co-polymer including (meth) acrylic acid and ethylacrylate (EA) forming aggregates in solution due to "sticky" contacts among hydrophobic EA-sequences. PAA/PVP-VI complexes are less compact and more deformable than the hydrophobic Sterocoll FD aggregates. Solutions of PAA/PVP-VI exhibit a higher zero-shear viscosity even at lower molecular weight of the aggregates, but are strongly shear-thinning in contrast to the weakly shear-thinning solutions of Sterocoll FD. The higher ratio of characteristic relaxation times in shear and elongation determined for PAA/PVP-VI compared to Sterocoll FD solutions reflects, that the charge-induced complexes provide a much stronger resistance to extensional flow than the aggregates formed by hydrophobic interactions. This is most likely due to a break-up of the latter in extensional flow, while there is no evidence for a break-up of complexes for PAA/PVP-VI mixtures. These flexible aggregates are more suitable for the stabilization of thin filaments in extensional flows.

• 한국강구조학회 논문집
• /
• 제20권6호
• /
• pp.691-700
• /
• 2008

최근 건축구조물의 구조는 다양한 형태의 복잡한 건축물이 구현되고 있다. 이러한 건축구조물의 복합 다양성은 수평저항력에 효과적 으로 저항하기 위해 강재와 접합부의 요구성능이 점차 중요시되고 있다. 접합부는 형상의 불연속과 응력집중 및 다축응력 등이 발생되는 부분으로 골조전체의 변형능력에 큰 영향을 미치고 강성과 인성을 결정하는 중요부위이다. 본 연구에서는 고강도 고성능강 적용에 대한 인성평가를 위해 구조체의 기둥-보 접합부를 빌트업 H형강의 T형 기둥-보 용접접합부로 제작하여 실대실험을 수행하였다. 실험변수는 응력집중 및 형상의 불연속이 발생되는 보 스캘럽을 중심으로 논스캘럽(Non-Scallop)과 종래형 스캘럽, 개량형 스캘럽으로 제작하여 스캘럽 형상이 접합부의 인성에 미치는 영향과 고강도 고성능강의 건축구조물 적용성을 평가하였다. 기존의 기둥-보 용접접합부에 대한 평가방법을 기초로 최근 개발된 고강도 고성능강의 초고층 건축물 적용을 위한 내진설계 자료를 제시하였다.

• 한국압력기기공학회 논문집
• /
• 제13권2호
• /
• pp.75-83
• /
• 2017

In severe accident conditions of light water reactors, the loss of coolant may cause problems in integrity of zirconium fuel cladding. Under the condition of the loss of coolant, the zirconium fuel cladding can be exposed to high temperature steam and reacted with them by producing of hydrogen, which is caused by the failure in oxidation resistance of zirconium cladding materials during the loss of coolant accident scenarios. In order to avoid these problems, we develop a multi-metallic layered composite (MMLC) fuel cladding which compromises between the neutronic advantages of zirconium-based alloys and the accident-tolerance of non-zirconium-based metallic materials. Cold pilgering process is a common tube manufacturing process, which is complex material forming operation in highly non-steady state, where the materials undergo a long series of deformation resulting in both diameter and thickness reduction. During the cold pilgering process, MMLC claddings need to reduce the outside diameter and wall thickness. However, multi-layers of the tube are expected to occur different deformation processes because each layer has different mechanical properties. To improve the utilization of the pilgering process, 3-dimensional computational analyses have been made using a finite element modeling technique. We also analyze the dimensional change, strain and stress distribution at MMLC tube by considering the behavior of rolls such as stroke rate and feed rate.

• 한국구조물진단유지관리공학회 논문집
• /
• 제15권4호
• /
• pp.99-106
• /
• 2011

본 연구는 LB-DECK의 합성 전과 후 적절한 설계방법을 적용하기 위하여 PBD의 기초 개념에 근거하여 성능향상을 위한 연구를 수행하였다. 그 결과, 합성 전 폴리머 콘크리트를 활용함에 따라 휨 인장강도를 증가시켜 미세균열을 감소시킬 수 있으며, 심미적인 효과를 기대할 수 있고, 낮은 침투성으로 인하여 내구성을 향상시키고, 이에 따른 피복두께를 감소시킬 수 있을 것으로 평가되었다. 또한 합성 후 경험적 설계법을 적용한 LB-DECK 바닥판은 일반적인 바닥판보다 하중 저항능력이 우수하여 안전성이 증가되며, 강도설계법 적용시와 달리 지간이 증가되어도 철근배근방법과 철근배근량이 일정하기 때문에 시공성과 경제성을 동시에 확보할 것으로 기대된다.

• 한국작물학회지
• /
• 제47권
• /
• pp.175-185
• /
• 2002

Rapeseed(Brassica napus L.) is an important oil crop as a vegetable oil, concentrated feed and industrial materials. The name "canola" was registered in 1979 by the Western Canadian Oilseed Crushers Association to describe "double-low" varieties. Double low indicates that the processed oil contains less than 2% erucic-acid and the meal less than 3mg/g of glucosinolates. Today annual worldwide production of rapeseed is approximately 35 million tons on 24 million hectares. China accounts for 33% of the world production and the European Economic Community for nearly 32%. Canola ranks 3rd in production among the world's oilseed crops following soybeans, sunflowers, peanuts and cottonseed. The recent advances in genomics and in gene function studies has allowed us to understand the detailed genetic basis of many complex traits, such as flowering time, height, and disease resistance. The manipulation of seed oil content via transgene insertion has been one of the earliest successful applications of modern biotechnology in agriculture. For example, the first transgenic crop with a modified seed composition to be approved for unrestricted commercial cultivation in the US was a lauric oil, rape-seed, grown in 1995. There were also some significant early successes, mostly notably the achievement of 40% to 60% lauric acid content in rapeseed oil, which normally accumulates little or no lauric acid. The name "$\textrm{Laurical}^{TM}$" was registered in 1995 by Calgene Inc. Nevertheless, attempts to achieve high levels of other novel fatty acids in seed oils have met with much less success and there have been several reports that the presence of novel fatty acids in transgenic plants can sometimes lead to the induction of catabolic pathways which break down the novel fatty acid, i.e. the plant recognizes the "strange" fatty acid and, far from tolerating it, may even actively eliminate it from the seed oil. It is likely that, in the future, transgenic oil crops and newly domesticated oil crops will both be developed in order to provide the increased amount and diversity of oils which will be required for both edible and industrial use. It is important that we recognize that both approaches have both positive and negative points. It will be a combination of these two strategies that is most likely to supply the increasing demands for plant oils in the 21st century and beyond.ant oils in the 21st century and beyond.

• Archives of Plastic Surgery
• /
• 제47권2호
• /
• pp.187-193
• /
• 2020

Upper limb nerve damage is a common condition, and evidence suggests that functional recovery may be limited following peripheral nerve repair in cases of delayed reconstruction or reconstruction of long nerve defects. A 26-year-old man presented with traumatic injury from a wide, blunt wound of the right forearm caused by broken glass, with soft tissue loss, complete transection of the radial and ulnar arteries, and a large median nerve gap. The patient underwent debridement and subsequent surgery with a microsurgical free radial fasciocutaneous flap to provide a direct blood supply to the hand; the cephalic vein within the flap was employed as a venous vascularized chamber to wrap the sural nerve graft and to repair the wide gap (14 cm) in the median nerve. During the postoperative period, the patient followed an intensive rehabilitation program and was monitored for functional performance over 5 years of follow-up. Our assessment demonstrated skin tropism and sufficient muscle power to act against strong resistance (M5) in the muscles previously affected by paralysis, as well as a good localization of stimuli in the median nerve region and an imperfect recovery of two-point discrimination (S3+). We propose a novel and efficient procedure to repair >10-cm peripheral nerve gap injuries related to upper limb trauma.

• Animal cells and systems
• /
• 제15권3호
• /
• pp.227-233
• /
• 2011

The Nramp1/Slc11a1 locus encodes a proton-coupled divalent cation transporter, expressed in late endosomes/lysosomes of macrophages, that constitutes a component of the innate immune response to combat intracellular pathogens and it was shown to play an important role in regulating inherent immunity. The previously identified Z-DNA forming polymorphic repeat(GT)n in the promoter region of the human Nramp1 gene does act as a functional polymorphism influencing gene expression. Research has shown that INF-${\gamma}$, TNF-${\alpha}$, IL-$1{\beta}$ and bacteria LPS increase the level of Nramp1 expression. However, the molecular mechanism for Nramp1 gene regulation is unclear. In this research, bovine Nramp1 5'-flanking region (-1748~+769) was cloned and analyzed by bioinformatics. Then to find the core promoter and the cis-acting elements, deletion analysis of promoter was performed using a set of luciferase reporter gene constructs containing successive deletions of the bovine Nramp1 5'-flanking regions. Promoter activity analysis by the dual luciferase reporter assay system showed that the core promoter of Nramp1 was located at +58~-89 bp. Some positive regulatory elements are located at -89~-205 bp and -278~-1495 bp. And the repressor elements were in region -205~-278 bp, intron1 and -1495~-1748 bp. LPS-responsive regions were located at -1495~-1748 bp and -278~-205 bp. The present study provides an initial effort to explore the molecular mechanism of transcriptional activation of the bovine Nramp1 gene and should facilitate further studies to decode the complex regulatory process and for molecular breeding for disease resistance in bovines.

• Macromolecular Research
• /
• 제14권5호
• /
• pp.530-538
• /
• 2006

There are three important components in tissue engineering: the cells, signaling factors (cytokines and growth factors), and scaffolds. To obtain finely engineered tissue, all three components should perform their individual functions and be fully integrated with each other. For the past few years, we have studied the characteristics of photodimerizable HA (CHA)/alginate (CA) composite materials. CHA/CA complex hydrogels, which were irradiated under UV light and, then treated with calcium ions, were found to have good biocompatibility, mechanical properties and water resistance for implantable tissue scaffolds. In this study, we introduced a cell growth factor (basic fibroblast growth factor; bFGF) into the CHA/CA scaffolds and studied its release behavior. We also introduced tetracycline hydrochloride and flurbiprofen into the same scaffolds as model activation factors and evaluated their release behaviors from the scaffolds. The drug release rate from the materials was influenced by various parameters, such as the degree of crosslinking, the cross linker type, the physico-chemical properties of the drug, and the amount of the drug in the polymer. The results indicated that the negatively charged CHA/CA composite materials showed sustained release behavior and that HA has a particularly strong negative charge, making it attractive toward tetracycline hydrochloride and bFGF, but repulsive toward flurbiprofen.

• 산업경영시스템학회지
• /
• 제40권2호
• /
• pp.145-149
• /
• 2017

One of the challenges facing precision manufacturers is the increasing feature complexity of tight tolerance parts. All engineering drawings must account for the size, form, orientation, and location of all features to ensure manufacturability, measurability, and design intent. Geometric controls per ASME Y14.5 are typically applied to specify dimensional tolerances on engineering drawings and define size, form, orientation, and location of features. Many engineering drawings lack the necessary geometric dimensioning and tolerancing to allow for timely and accurate inspection and verification. Plus-minus tolerancing is typically ambiguous and requires extra time by engineering, programming, machining, and inspection functions to debate and agree on a single conclusion. Complex geometry can result in long inspection and verification times and put even the most sophisticated measurement equipment and processes to the test. In addition, design, manufacturing and quality engineers are often frustrated by communication errors over these features. However, an approach called profile tolerancing offers optimal definition of design intent by explicitly defining uniform boundaries around the physical geometry. It is an efficient and effective method for measurement and quality control. There are several advantages for product designers who use position and profile tolerancing instead of linear dimensioning. When design intent is conveyed unambiguously, manufacturers don't have to field multiple question from suppliers as they design and build a process for manufacturing and inspection. Profile tolerancing, when it is applied correctly, provides manufacturing and inspection functions with unambiguously defined tolerancing. Those data are manufacturable and measurable. Customers can see cost and lead time reductions with parts that consistently meet the design intent. Components can function properly-eliminating costly rework, redesign, and missed market opportunities. However a supplier that is poised to embrace profile tolerancing will no doubt run into resistance from those who would prefer the way things have always been done. It is not just internal naysayers, but also suppliers that might fight the change. In addition, the investment for suppliers can be steep in terms of training, equipment, and software.

• Corrosion Science and Technology
• /
• 제11권3호
• /
• pp.77-81
• /
• 2012

Cathodic protection(CP) is widely used as a means of protecting corrosion for not only marine structures like ship hulls and offshore drilling facilities, but also underground structures like buried pipelines and oil storage tanks. The principle of CP is that the anodic dissolution of metal can be protected by supplying electrons to the cathode metal. When unprotected structures are nearby to CP systems, interference problems between unprotected and protected structures may be happened. The stray current interference can accelerate the corrosion of nearby structures. So far many efforts have been made to reduce the interference in the electric railway systems adjacent to the underground metal structures like buried pipelines and gas/oil tanks. During recent few decades the protection technologies against stray current induced corrosion have been significantly improved and a number of techniques have been developed. However, there is very limited information an marine environments. Some complex harbor structures are protected by two cathodic protection systems, i.e. sacrificial anode cathodic protection(SACP) and impressed current cathodic protection(ICCP). In this case, when the protection current from sacrificial anodes returns to the cathode through electrolyte, it passes through nearby other low resistance metal structures. In many cases the stray current of ICCP systems influences the function of SACP. In this study, the risk of stray current from the SACP system to adjacent reinforced concrete structures has been verified through laboratory experiments. Concrete and steel pile structures modeled a part of bridge have been investigated in terms of CP potential and current between the two. The variation of stray current according to the magnitude of ICCP/SACP has been studied to mitigate it and to suggest the proper protection criteria.