• Journal of Welding and Joining
• /
• v.24 no.5
• /
• pp.57-61
• /
• 2006

For the production of functional $TiO_2$-biodegradable plastic (polybutylene succinate:PBS) composite material with photocayalytic activity, we attempted to prepare $TiO_2$ coatings on PBS substrate by HVOF and plasma spraying techniques under various conditions. The microstructures of coatings were characterized with SEM and XRD analysis, and the photocatalytic efficiency of coatings was evaluated by the photo degradation of gaseous acetaldehyde. The effects of primary particle size and spraying parameters on the formation behavior, photocatalytic performance of the coatings have been investigated. The results indicated that for both the HVOF sprayed $P_{200}$ and $P_{30}$ coatings, the high anatase ratio of 100% can be achieved regardless of fuel gas pressure. On the other hand, the HVOF sprayed $P_7$ coating exhibited a largely decreased anatase ratio (from 100% to 49.1%) with increasing the fuel gas pressure, which may be attributed to much higher susceptibility of heat for 7 nm agglomerated powder. HVOF sprayed $P_{200}$ and $P_{30}$ coatings show better performance as compared to that of plasma sprayed $P_{200}$ coatings owing to the higher anatase ratio. However, the HVOF sprayed $P_7$ coatings did not show the photocatalytic activity, which may result from the extremely small reaction surface area to the photocatalytic activity and low anatase ratio.

• Korean Journal of Materials Research
• /
• v.10 no.9
• /
• pp.619-623
• /
• 2000

Alumina membrane was prepared by sol-gel coating method using boehmite powder(${\Upsilon}-AlOOH$). The supported and the unsupported alumina membrane were fabricated to investigate the phase transformation and change of microstructure. It is important to control the homogeneous pore size and distribution in application of filtering process. The ${\theta}-to\;{\alpha}-AL_2O_3$ phase transformation (XRD) and the change of microstructure was investigated using scanning electron microscopy(SEM). XRD patterns showed that the supported membrane had $100^{\circ}C$ higher ${\theta}-to\;{\alpha}-AL_2O_3$ transformation temperature compared to the unsupported membrane. The similar effect was also observed for microstructural change of the membrane.

• Journal of the Korean Society of Safety
• /
• v.22 no.5
• /
• pp.77-83
• /
• 2007

This study is conducted on spontaneous ignition temperature and activation energy of Hydroxypropyl Methyl Cellulose(HMC) powder. HMC is a kind of cellulose derivative and used as additives for building material, surface coating, printing ink, adhesives, cosmetics and medical supplies. So this material has been widely used as important additive in the chemical industry fields and a mount of production has increased year by year. Therefore, it is very important to find out the thermal ignition characteristics of its danger and the critical ignition temperature. This study was performed by the Spontaneous Ignition Tester(SIT) and so on. Based on the data of the SIT-II, the critical ignition point of HMC is about $186^{\circ}C$ which is slightly lower than normal cellulose.

• Journal of Dairy Science and Biotechnology
• /
• v.37 no.4
• /
• pp.213-222
• /
• 2019

Milk and dairy products are the high value foods for the elderly population. In particular, fermented milk is the best source of calcium for people in the specific age group of over 79 years. It provides a good source of protein. Regular exercise and active lifestyle are recommended to slow down the muscle loss. However, exercising without proper nutrient intake is simply not sufficient at this age. Milk and dairy products provide the iron and protein content required for effective exercise-assisted growth. Milk nutrients have the advantage of being produced in various food forms, such as liquid, semi-solid, and powder types. Fat-soluble vitamins such as retinol and vitamin K can be encapsulated using various technologies for milk and dairy products. Using the encapsulation method, spray drying and fluidized-bed coating have been used for adding the micro-nutrients to the food. Microencapsulation technology is being applied in case of the fermented dairy products too. In particular, various wall materials are being developed to enhance the viability of probiotics. In the near future, advanced high-efficiency technologies that can effectively nourish the dairy products with nutrients will be developed to produce targeted high-nutrition value food for the elderly.

• Journal of Environmental Science International
• /
• v.17 no.9
• /
• pp.1023-1032
• /
• 2008

The feasibility study of the application of the photoelectrocatalytic and electrolytic/UV decolorization of Rhodamine B (RhB) was investigated in the photoelectrocatalytic and electrolytic/UV process with $TiO_2$ photoelectrode and DSA (dimensionally stable anode) electrode. Three types of $TiO_2$ photoelectrode were used. Thermal oxidation electrode (Th-$TiO_2$) was made by oxidation of titanium metal sheet; sol-gel electrode (5G-$TiO_2$) and powder electrode (P-$TiO_2$) were made by coating and then heating a layer of titania sol-gel and slurry $TiO_2$ on titanium sheet. DSA electrodes were Ti and Ru/Ti electrode. The relative performance for RhB decolorization of each of the photoelecoodes and DSA electrodes is: Ru/Ti > Ti > SG-$TiO_2$ > Th-$TiO_2$. It was observed that photoelectrocatalytic decolorization of RhB is similar to the sum of the photocatalytic and electrolytic decolorization. Therefore the synergetic effect was not showed in pthotoelectrocatalytic reaction. $Na_{2}SO_{4}$ and NaCl showed different decolorization effect between pthotoelectrocatalytic and electrolytic/UV reaction. In the presence of the NaCl, RhB decolorization of Ru/Ti DSA electrode was higher than that of the other photoelectrode and Ti electrode. Optimum current, NaCl dosage and UV lamp power of the electrolytic/UV process (using Ru/Ti electrode) were 0.75 A, 0.5 g/L and 16 W, respectively.

• Journal of the Korean Ceramic Society
• /
• v.22 no.4
• /
• pp.54-60
• /
• 1985

Gas sensing materials for detecting flammable gases such as $CH_4$, $C_3H_8$ and n-$C_4H_{10}$ were developed by util-izing $In_2O_3$ as the principal sensing material. The sensing materials were formulated by mixing $In_2O_3$ powder with one or two other chemicals such as $SnO_2$, $Y_2O_3$ and $Al_2O_3$ with a small addition of $PdCl_2$ as a catalyst. Sample of sensor were fabricated by coating each of the mixtures on a ceramic tube impregnating ethylsili-cate and firing at 75$0^{\circ}C$ Each material mixture was evaluated by measuring and comparing gas sensitivity(resistance in air/resistance with gas) to flammable gases such as $CH_4$, $C_3H-8$ and n-$C_4H_{10}$. It was found that among fifteen compositions tested three compositions as follows show the highest gas sensitivity and thus are very feasible for commercialization as the gas sensors ; o49.5 $In_2O_3$+50 Al2O3_0.5 PdCl2(wt%) o $20In_2O_3+29$ $SnO_2+50$ $Al_2O_3+1$ $PdCl_2$(wt%) o40 $In_2O_3$+9 $Y_2O_3+50$ $Al_2O_3+1$ $PdCl_2$(wt%)

• Journal of the Korean Ceramic Society
• /
• v.44 no.8
• /
• pp.445-450
• /
• 2007

A conversion layer of SiC was fabricated on the graphite substrate by a chemical vapor reaction method in order to enhance the oxidation resistance of graphite. The effect of boron carbide containing powder bed on the morphology of SiC conversion layer was investigated during the chemical vapor reaction of graphite with the reactive silicon-source at $1650^{\circ}C\;and\;1700^{\circ}C$ for 1 h. The presence of boron species enhanced the conversion of graphite into SiC, and altered the morphology of the conversion layer significantly as well. A continuous and thick SiC conversion layer was formed only when the boron source was used with the other silicon compounds. The boron is deemed to increase the diffusion of SiOx in SiC/C system.

• Applied Chemistry for Engineering
• /
• v.29 no.4
• /
• pp.425-431
• /
• 2018

Composite particles of porous silica and cerium oxide nanoparticles blocking UV/blue light were prepared through a dry coating process. Various composite particles were prepared by varying conditions such as the mixing ratio of cerium oxide and silica, and the chamber rotating speed of mechano fusion system. The surface morphology of the composite particles was observed with SEM and the composition was analyzed using X-ray fluorescence (XRF). When the cerium oxide/silica composite particles were dispersed in water, the transparency and dispersion stability of the colloidal solution were improved. In addition, the fluidity and spreadability of the particle powder were enhanced by making composite particles. These results show that cerium oxide/silica composite particles can be used as functional cosmetic ingredients for UV/blue light protection.

• Korean Journal of Materials Research
• /
• v.30 no.10
• /
• pp.550-557
• /
• 2020

Used in the ceramic tile market as a representative building material, relief ceramic tile is showing increased demand recently. Since ceramic tiles are manufactured through a sintering process at over 1,000 ℃ after uniaxial compression molding by loading granule powders into a mold, it is very important to secure the flowability of granular powders in a mold having a relief pattern. In this study, kaolin, silica, and feldspar are used as starting materials to prepare granule powders by a spray dryer process; the surface of the granule powders is subject to hydrophobic treatment with various concentrations of stearic acid. The effect on the flowability of the granular powder according to the change of stearic acid concentration is confirmed by measuring the angle of repose, tap density, and compressibility, and the occurrence of cracks in the green body produced in the mold with the relief pattern is observed. Then, the green body is sintered by a fast firing process, and the water absorption, flexural strength, and durability are evaluated. The surface treatment of the granule powders with stearic acid improves the flowability of the granule powders, leading to a dense microstructure of the sintered body. Finally, the hydrophobic treatment of the granule powders makes it possible to manufacture relief ceramic tiles having a flexural strength of 292 N/cm, a water absorption of 0.91 %, and excellent mechanical durability.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.6
• /
• pp.52-57
• /
• 1999

Funtional metal prototypes are often required in numerous industrial applications. These components are typically needed in the early stage of a project to determine form, fit and function. Recent R/P(Rapid Prototyping) part are made of soft materials such as plastics, wax, paper, these master models cannot be employed durable test in real harsh working environment. Parts by direct metal rapid tooling method, such as laser sintering, by now are hard to get net shape, pores of the green parts of powder casting method must be infiltrated to get proper strength as tool, and new type of 3D direct tooling system combining fabrication welding arc and cutting process is reported by song etc. But a system which can build directly 3D parts of high performance functional material as metal part would need long period of system development, massive investment and other serious obstacles, such as patent. In this paper, through the rapid tooling process as silicon rubber molding using R/P master model, and fabricate wax pattern in that silicon rubber mold using vacuum casting method, then we tranlsated the wax patterns to numerous metal prototypes by new investment casting process combined conventional investment casting with rapid pototyping & rapid tooling process. with this wax-injection-mold-free investment casting, we developed new investment casting process of fabricating numerous functional metal prototypes from one master model, combined 3-D CAD, R/P and conventional investment casting and tried to expect net shape measuring total dimension shrinkage from R/P part to metal part.