• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.10
• /
• pp.1824-1832
• /
• 1992

This study investigated the compressive Young's modulus and the impactinduced damage of CFRP angle-ply laminate under same impact energy condition. The specimens of angle-ply laminate composites [0.deg.$_{6}$/ .theta..deg.$_{10}$/ 0.deg.$_{6}$] with .theta..deg. =30.deg., 45.deg., 60.deg. and 90.deg. were employed, and damaged by steel balls of diameter of 5mm and 10mm propelled by air gun type impact testing machine. The impact damaged zones were observed through a scanning acoustic microscope(SAM), and their cross-sections were observed through a scanning electron microscope(SEM). The compressive Young's moduli before and after impact were measured, and compared with the theoretical values calculated. The results obtained were as follows: (1) The damage areas on the interfacial boundaries showed more severe change on the back side interface than on the impact side interface with increasing ply-angle. (2) The damage areas on the interfacial boundaries became larger with increasing impact velocity or ply-angle. (3) The impact damaged zone showed the delamination on the interfacial boundaries and transverse cracks inside laminas. (4) The impact damaged zone was affected by the impactor size and speed or ply-angle under same impact energy condition. (5) Compressive Young's moduli before and after impact were lower than theoretical value, but showed a similar change according to ply-angle. (6) Compressive Young's moduli after impact were higher than those before impact, but there was no remarkable change in apparent compressive modulus after impact.t.act.

• The korean journal of orthodontics
• /
• v.36 no.2 s.115
• /
• pp.161-169
• /
• 2006

The purpose of this study was to investigate cephalometrically the short term static velopharyngeal changes in 25 patients (10 boys and 15 girls, aged from 5 years 9 months to 12 years 10 months in the beginning of treatment) with skeletal Class III malocclusions who underwent nonsurgical maxillary protraction therapy with a facemask. The linear, angular and ratio measurements were made on lateral cephalograms. Only the change in hard palatal plane angle was negatively correlated with the change in maxillary depth or N-perp to A (p<0.01). The change in velar angle showed a statistically significant increase (p<0.001). This change was influenced more by the soft palatal plane angle than by the hard palatal plane angle (p<0.001). The changes in soft tissue nasopharyngeal depth and hard tissue nasopharyngeal depth showed statistically significant increases (p<0.001). Correlations between the changes in soft tissue (or hard tissue) nasopharyngeal depth and the change in soft palatal plane angle were significant (p<0.05). The increase in hard palate length was statistically significant (p<0.001). The change in hard palate length was negatively correlated with the change in soft tissue nasopharyngeal depth (p<0.05). The change in need ratio S (C) showed a statistically significant increase (p<0.001). But this difference was within the normal range reported by previous studies. These findings indicate that the velopharyngeal competence was maintained even if the anatomical condition of the static velopharyngeal area were changed after maxillary protraction.

• The Journal of Korean Physical Therapy
• /
• v.15 no.3
• /
• pp.1-15
• /
• 2003

The purpose of this study was to evaluate the change of lower extremity alignment according to plantar surface compliance in standing status. The thirty normal adults (15 men and 15 women) aged between 20 and 29 were assigned to 3 groups: control group, experimental groups (AHPS group, ASPH group). The lower extremity alignment was examined before and after adaptation with corresponding foam types. The results of this study were as follows : 1. As the result of comparing lower extremity alignment before and after test of the control group which any change did not exist in plantar surface compliance, there were not significant differences in the angle A, B, C, D, E of right and left(p>0.05). 2. As the result of comparing lower extremity alignment before and after test of the AHPS group which forefoot part of plantar surface is hard and rear foot part is soft, there were not significant differences in the angle A of right and left(p>0.05). But, there were significantly decreased in the angle B, C, D, E of right and left(p<0.05). 3. As the result of comparing lower extremity alignment before and after test of the ASPH group which forefoot part of plantar surface is soft and rear foot part is hard, there were not significant differences in the angle A of right and left(p>0.05). But, there were significantly increased in the angle B, C, D, E of right and left(p<0.05). 4. As the result of comparing lower extremity alignment of the control group, AHPS group and ASPH group, there were not significant differences in the angle A, B, C, D, E of right and left before test(p>0.05). But, there were significant differences in the angle C, D of right and left after test(p<0.05).

• Journal of Power System Engineering
• /
• v.17 no.1
• /
• pp.58-63
• /
• 2013

The aerodynamic performance of double inlet sirocco fan is strongly dependent upon the design factors of impeller and scroll. In this paper, the change of scroll size was adopted to investigate the aerodynamic performances of double inlet sirocco fan and indoor PAC. Especially, a scroll expansion angle and a cut-off clearance ratio were considered to change the scroll size. In addition, the installation depth between double inlet sirocco fan and indoor PAC was considered. As a result, the total pressure efficiency of double inlet sirocco fan shows about 62%~73% according to the change of scroll expansion angles. Moreover, the flowrate performance of indoor PAC is the best at the condition of a scroll expansion angle of 8°, an installation depth of 15 mm and a cut-off clearance ratio of 8%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.173-176
• /
• 2000

In this paper, we investigated the surface degradation of HTV silicone rubber used for a polymeric insulator by UV irradiation. To study the surface ageing properties by W irradiation, we used the corona discharge charging and contact angle. Therefore, we observed the change of surface charge retention and decrease of surface hydrophobicity. Also, we discussed the chemical change in the surface range using the analytic equipment such as SEM, ATR-FTIR, ESCA. Therefore, it is found that the scissor of characteristic bonding and the reattachment of oxidant bonding was developed by UV rays radiation. As discussing the corona ischarge charging and the change of contact angle, it is found the effect of UV irradiation and the mechanism of chemical reaction

• Korean Journal of Materials Research
• /
• v.25 no.1
• /
• pp.54-59
• /
• 2015

Glancing angle deposition (GLAD) is a powerful technique to control the morphology and microstructure of thin film prepared by physical vapor deposition. Chromium (Cr) thin films were deposited on a polymer substrate by a sputtering technique using GLAD. The change in thickness and Vickers microhardness for the samples was observed with a change in the glancing angle. The adhesion properties of the critical load (Lc) by a scratch tester for the samples were also measured with varying the glancing angle. The critical load, thickness and Vickers microhardness for the samples decreased with an increase in the glancing angle. However, the thickness of the Cr thin film prepared at a $90^{\circ}$ glancing angle showed a relatively large value of 50 % compared to that of the sample prepared at $0^{\circ}$. The results of X-ray diffraction and scanning electron microscopy demonstrated that the effect of GLAD on the microstructure of samples prepared by sputter technique was not as remarkable as the samples prepared by evaporation technique. The relatively small change in thickness and microstructure of the Cr thin film is due to the superior step-coverage properties of the sputter technique.

• International Journal of Aeronautical and Space Sciences
• /
• v.8 no.2
• /
• pp.98-106
• /
• 2007

The vortex flow characteristics of a double-delta wing, which can change the incidence angle of its apex strake was investigated through the wing-surface pressure measurement and the particle image velocimetry(PIV) measurement of the wing-leeward flow region. The apex strake has sharp edges and can change its incidence angle with a hinge line at the 23% chord position measured from the apex of the main wing. The present study revealed that the incidence-angle change of the apex strake could greatly alter the vortex flow pattern around the double-delta wing and the wing-surface pressure distribution, which suggested that the apex strake could be used as an effective device for the active control of delta-wing vortex flow.

• The Journal of Korean Academy of Orthopedic Manual Physical Therapy
• /
• v.22 no.2
• /
• pp.51-56
• /
• 2016

Background: The purpose of this study is to compare axis change during cervical flexion and extension according to lordosis angle to patients with scoliosis. Methods: Movement axis change was estimated during cervical flexion and extension in twenty-four scoliosis patients with hypolordosis using radiography. Subjects were divided into mild lordotic curve group (MLCG, n=12, $34{\sim}25^{\circ}$) and severe lordotic curve group (SLCG, n=12, less $25^{\circ}$) according to cervical lordosis angle. Results: During cervical flexion, both group showed movement axis change to upper part of cervical vertebra and SLCG showed greater than MLCG but there is no significant difference. During cervical extension, SLCG showed greater than MLCG and there is significant difference. Conclusion: It is considered that cervical hypolordosis acts as important factor to scoliosis and degenerative joint disease because it leads to change of movement axis and central route of joint.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.37 no.12
• /
• pp.854-861
• /
• 1988

The current source inverter-fed induction motor(CSIM) drive is widely used in industry because of its four quadrant operation, fuseless protection, fuseless protection, and ruggedness. the CSIM drive system, however, has shortcomins such as slow response and dynamic stability to load torque disturbance and reference speed change. Such a disadvantages can be compensated considerably by means of introducing additional angle angle control loop. The angle control method is dependent upon the inverter type. In this paper, simultaneus recovery and commutation inverter(SRCI) which is developed recently is considered.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.236-241
• /
• 2000

In the present industry, there is not only the cutting of iron metal, but also the cutting of alloy aluminum, brass and plastic to wood(Paulownia). A variety of material is used and these industry is made need of the cutting material but lots of experiments processing is not enough at the moment. At this point, our team processed the basic experiment about influencing of cutting angle of bite concerned to manufacture in the turning of non-iron metal. Generally speaking, we recognized that there was occurrence of increase of rough surface with increasing of cutting angle in the non-iron metal. but in the cutting of wood we knew, there was special change with change of cutting angle.