• Bulletin of the Korean Chemical Society
• /
• 제29권2호
• /
• pp.413-416
• /
• 2008

A synthesis route to ordered mesoporous carbons with controllable nitrogen content has been developed for high-performance EDLC electrodes. Nitrogen-doped ordered mesoporous carbons (denoted as NMC) were prepared by carbonizing a mixture of two different carbon sources within the mesoporous silica designated by KIT-6. Furfuryl alcohol was used as a primary carbon precursor, and melamine as a nitrogen dopant. This synthesis procedure gave cubic Ia3d mesoporous carbons containing nitrogen as much as 13%. The carbon exhibited a narrow pore size distribution centered at 3-4 nm with large pore volume (0.6-1 cm3 g-1) and high specific BET surface area (700-1000 m2 g-1). Electrochemical behaviors of the NMC samples with various N-contents were investigated by a two-electrode measurement system at aqueous solutions. At low current density, the NMC exhibited markedly increasing capacitance due to the increase in the nitrogen content. This result could be attributed to the enhanced surface affinity between carbon electrode and electrolyte ions due to the hydrophilic nitrogen functional groups. At high current density conditions, the NMC samples exhibited decreasing specific capacitance against the increase in the nitrogen content. The loss of the capacitance with the N-content may be explained by high electric resistance which causes a significant IR drop at high current densities. The present results indicate that the optimal nitrogen content is required for achieving high power and high energy density simultaneously.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 B
• /
• pp.648-650
• /
• 2002

SPLSSM may operate with very high efficiencies and near unity power factor, SPLSSM has been shown to be capable of desirable steady state performance, but is known to have undesirable staring performance because starting asynchronously by means of an induction cage, it operates in steady state performance of a PM motor. This combination provides the steady state performance of a permanent magnet motor without the need for an expensive drive system. However, that combination makes it difficult to analyze the transient behaviors. This paper investigates the behaviors of Single-Phase Line-Start Synchronous Motor using finite element method combined analytic method. It is shown that finite element modeling is capable of giving accurate prediction of performances. Varying the value of capacitance and material of permanent magnet shows the effect on the dynamic characteristics in this paper.

• 한국표면공학회지
• /
• 제40권2호
• /
• pp.82-90
• /
• 2007

Crevice corrosion is the accelerated attack occurred in the occluded cell under a crevice on the metal surface. Crevice corrosion behaviors of nickel-based alloys such as Alloy 600 and Alloy 690 were investigated in acidic solution with different chloride ion concentrations. Tests were carried out using the specially designed crevice cell with a very narrow Luggin capillary assembly to measure the potential inside the crevice. It is believed that crevice corrosion in active/passive system like nickel-based alloys has much to do with the properties of passive film and its repassivation characteristics, investigated by the capacitance measurement and by the abrading electrode technique, respectively. An attempt was made to elucidate the relationship between crevice corrosion behaviors, properties of passive film and its repassivation kinetics. Results showed that repassivation rate parameter $n1{\leq}0.6$ and/or $n2{\leq}0.5$ indicated the possible occurrence of crevice corrosion.

• Journal of Mechanical Science and Technology
• /
• 제17권11호
• /
• pp.1650-1658
• /
• 2003

This paper deals with a novel shunt circuit, which is capable of suppressing multimode vibration amplitudes by using a pair of piezoceramic patches. In order to describe the characteristic behaviors of a piezoelectric damper connected with a series and a parallel resistor-negative capacitor branch circuit, the stiffness ratio and loss factor with respect to the non-dimensional frequency are considered. The mechanism of the shunt damper is also described by considering a shunt voltage constrained by shunt impedance. To obtain a guideline model of the piezo/beam system with a negative capacitive shunting, the governing equations of motion are derived through the Hamilton's principle and a piezo sensor equation as well as a shunt-damping matrix is developed. The theoretical analysis shows that the piezo/beam system combined with a series and a parallel resistor-negative capacitor branch circuit developed in this study can significantly reduce the multiple-mode vibration amplitudes over the whole structural frequency range.

• 한국응용과학기술학회지
• /
• 제28권3호
• /
• pp.329-334
• /
• 2011

The electrochemical performances of an asymmetric hybrid capacitor were investigated using $LiFePO_4$ as the positive electrode and active carbon fibers(ACF) as the negative electrode. The electrochemical behaviors of a nonaqueous hybrid capacitor were characterized by constant current charge/discharge test. The specific capacitance using $LiFePO_4$/ACF electrode turned out to be $0.87F/cm^2$ and the unit cell showed excellent cycling performance. This hybrid capacitor was able to deliver a specific energy as high as 178 Wh/kg at a specific power of 1,068 W/kg.

• 전기의세계
• /
• 제20권4호
• /
• pp.23-30
• /
• 1971

The photovoltaic behaviors ahve been observed with a sandwich-type cell, consisting of a junction between .betha.-carotene and stannic oxide conducting layer to provide a junction electrode. In the stannic oxide and .betha.-carotene junction it was found that its electromotive forse decreased to a value smaller than the original one. This is due to a space charge formation. Photovoltage reached approximately 40mV with an irradiation energy of 250Kcal/M$^{2}$hr. It appeared that a magnitude of the photovoltaic response was proportional to the logarithm of irradiance. The time constant of the photovoltaic effect was shown to be approximately 0.7 sec. The wavelength dependence of the photovoltaic behavior was very anomalous. It is assumed that such an anomalous photoresponse depends on a internal capacitance due to some bubble during process to make a cell.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제5C권4호
• /
• pp.171-175
• /
• 2005

A new type of supercapacitor was constructed by using carbon nanofibers (CNFs) and DAAQ (l,5-diaminoanthraquinone) oligomer. DAAQ was deposited on the carbon nanofibers by chemical polymerization with ammonium peroxodisulfate (($NH_4)_2S_2O_8$) as oxidant in the 0.1 M $H_2SO_4$. Polymerization reaction was carried out with constant sonication. From the analysis, it is clear that surface of carbon nanofibers was quite uniformly coated with DAAQ. The performance characteristics of the supercapacitors have been evaluated using Cyclic Voltammetry. CNFs/DAAQ based composite electrode showed relatively good electrochemical behaviors in acidic electrolyte system. CNFs/DAAQ composite electrode showed relatively good capacitance (7 Ah/kg) compared to conventional capacitors in the range of $-0.4\~0.4$.

• Journal of Power Electronics
• /
• 제19권1호
• /
• pp.296-306
• /
• 2019

The flyback topology is being widely used in power adapters. The coupling capacitance between primary and secondary windings of a flyback transformer is the main path for common-mode (CM) noise conduction. A Y-cap is usually used to effectively suppress EMI noise. However, this results in problems in space, cost, and the danger of safety leakage current. In this paper, the CM noise behaviors due to the electric field coupling of the transformer windings in a flyback adapter with synchronous rectification are analyzed. Then a scheme with balance winding is proposed to reduce the CM noise with a transformer winding design that eliminates the Y-cap. The planar transformer has advantages in terms of its low profile, good heat dissipation and good stray parameter consistency. Based on the proposed scheme, with the help of a full-wave simulation tool, the key parameter influences of the transformer PCB winding design on CM noise are further analyzed. Finally, a PCB transformer for an 18W adapter is designed and tested to verify the effectiveness of the balance winding scheme.

• 한국진공학회지
• /
• 제15권1호
• /
• pp.64-72
• /
• 2006

우리는 tris-(8-hydroxyquinoline) aluminum (Alq3)와 같은 단분자 유기물 박막을 사용하여 유기물 발광 소자(OLEDs)를 제작하였다. OLEDs는 ITO가 증착된 유기 기판 위에서 제조되었고, 수명 측정 이후의 OLEDs에 대한 발광, 축전 용량, 유전 손실 특성 등을 측정하였다. 여기서, 수명 측정을 위하여 사용한 인가 전류는 0.5mA 에서 9mA까지 였고, 수명의 인가 전류 의존성은 약 2 mA 부근에서 다르게 관찰되었다. C-V 특성 곡선에서 나타난 축전 용량의 봉우리들은 유기물 내의 분극과 유기물과 금속의 경계에서 나타난 분극의 영향으로 추측된다. 그리고, 2 mA 보다 낮은 전류 하에서 수명 측정 후 발광특성이 저하된 OLEDs에서는 소자 내의 분극 크기의 감소와 전하 유입 장벽의 낮아짐이 같이 관찰되었다.

• 폴리머
• /
• 제36권3호
• /
• pp.321-325
• /
• 2012

본 연구에서는 화학적으로 활성 흑연나노섬유를 제조하여 그에 따른 전기화학적 거동을 확인하였다. 활성화제로 KOH를 사용하였으며, KOH와 흑연나노섬유의 비를 무게비로 각각 0, 1, 2, 4, 및 5로 처리하여 표면과 기공특성을 연구하였고, 그에 따른 전기화학적 거동을 살펴보았다. 활성화된 흑연나노섬유의 결정구조와 표면특성은 각각 X-선 회절분석법(XRD), 주사전자현미경(SEM) 분석방법을 이용하여 확인하였으며, 기공 특성은 비표면적 장치(BET)를 이용하였으며 질소흡착 등온선에 의해 조사하였다. 전기화학적 특성은 10 mV/s의 주사속도로 순환전류전압(cyclic voltammetry)을 통한 곡선으로 고찰하였으며 정전류법(galvanostatic method)으로 측정된 충방전 곡선을 통해 비축전용량을 계산하였다. 실험 결과로부터, 활성 흑연나노섬유의 전기화학적 거동은 KOH 양이 증가함에 따라 향상되었으며, 4 배 처리된 활성 흑연나노섬유가 최대의 비축전용량을 가진 것으로 나타났다. 이것은 KOH 활성화에 의해 활성 흑연나노섬유의 비표면적과 기공부피가 증가하기 때문인 것으로 사료된다.