• 대한전기학회논문지
• /
• 제40권6호
• /
• pp.626-629
• /
• 1991

The negative wire of an electrolytic ozone generator, proposed by authors, has been contaminated by attaching the impurity particulate in tap water, which is called BUILD-UP phenomenon. The higher applied voltage and the larger wire diameter have shown the higher build-up rate, which makes the current reducing largely and concurrently the ozone production smaller. It is found that the positive electrode of the ozone generator has a strong SELF-CLEANING effect by detaching the impurity particulate from its surface, which, however, is used us a novel means of solving the build-up problem. As a result, the build-up problem can be solved effectively by applying an alternate square wave pulse voltage to the electrodes so as to get the self-cleaning ability on the both electrodes during each of the half pulse duration time.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.14-15
• /
• 2006

Application of the parallel Build-up is increasing continuously. This report presents about the PCB Build-up technology since 2000. Among the parallel build-up technologies, PALAP application - after making the via, filling the via with electric conductive paste, then expose to make wiring pattern and put them by layer without any glue or middle - is actively developing, especially DENSO company.

• International Journal of Precision Engineering and Manufacturing
• /
• 제4권4호
• /
• pp.51-56
• /
• 2003

Generally, the build-up printed circuit board manufactured by a sequential process involving etching, plating, drilling, etc, which requires many types of equipments and long lead time. Etching process is suitable for mass production, however, it is not adequate for manufacturing a prototype in the development stage. In this study, we introduce a screen printing technology for prototyping a build-up printed circuit board. As for the material, photo/thermal curable resin and conductive paste are used for the formation of dielectric and conductor. The build-up structure is made by subsequent processes such as formation of a liquid resin thin layer, solidification by a UV/IR light, and via hole filling with a conductive paste. By use of photo curable resin, productivity is greatly enhanced compared with thermal curable resin. Finally, the basic concept and the possibility of build-up printed circuit board prototyping are proposed in comparison with the conventional process.

• 마이크로전자및패키징학회지
• /
• 제6권4호
• /
• pp.15-22
• /
• 1999

일반적으로 빌드업 다층 인쇄회로기판은 에칭, 도금등의 습식공정에 의해 제작이 이루어지므로 많은 장비와 많은 시간이 필요하게 된다. 이러한 습식공정은 양산에는 적합하지만 개발단계에서는 그리 적합하지 않은 방법이다. 본 연구에서는 스크린 인쇄기술을 도입하여 빌드업 다층 인쇄회로기판을 제작하여 보았다. 절연성 재료로는 광경화성수지 또는 열경화성수지를 사용하였으며 전도성 재료로는 전도성 페이스트를 사용하였다. 층간의 전기적 연결을 담당하는 비아와 회로를 형성하기 위해 스크린 인쇄공정을 통해 전도성 페이스트를 인쇄 하였다. 이러한 방법을 통해 제품의 개발 단계에서 기존의 빌드업 다층 인쇄회로기판 제작 공정과 비교하여 좀더 효율적인 방법을 제시하였다.

• 한국정밀공학회지
• /
• 제13권4호
• /
• pp.163-173
• /
• 1996

Stereolithography is a process used to rapidly produce polymer components directly form a computer representation of the part. There are several considerations to be made for the efficient use of the process. Especially, the build-up orientation of part critically affects the part accuracy, total build time and the volume of support structures. The purpose of tis study is to determine the optimal build-up part orientation for the SLA process with improving part accuracy, and minimizing total build time and the volume of support structures. The forst factor is related to the area of surfaces whioch have staircase protrusions after solidification, the second factor is related to the total number of layers, and the third factor is related to the area of the surfaces which need to be supported with support structures. An algorithm is developed to calculate the staircase area, quantifying the process errors by the volume of materials supposed to be removed or added to the part, and the optimal layer thickness for the SLA system which can handle the variable layer thickness. So the optima l part orientation is determined based on the user's selections of primary criter- ion and the optimal thickness of layers is calculated at any part orientations.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제29회 춘계학술대회
• /
• pp.127-132
• /
• 1999

The inlet pressure build-up at the leading edge of bearings which have discontinuous lubrication surface is analyzed theoretically. The analyses of Inlet pressure build-up is obtained by means of full Navier-stokes equations. Beam-warming method is used to solve navier-stokes equations. The results show that inlet pressure is above atmosphere pressure in front of leading edge of hearing.

• Tribology and Lubricants
• /
• 제22권2호
• /
• pp.59-65
• /
• 2006

In hard disk drives as the head to disk spacing continues to decrease to facilitate recording densities, slider disk interactions have become much more severe due to direct contact of head and disk surfaces in both start/stop and flying cases. The slider disk interaction in CSS (contact-start-stop) mode is an important source of particle generation and tribocharge build-up. The tribocharge build-up in the slider disk interface can cause ESD (electrostatic discharge) damage. In turn, ESD can cause severe melting damage to MR or GMR heads. The spindle speed of typical hard disk drives has increased in recent years from 5400 rpm to 15000 rpm and even higher speeds are anticipated in the near future. And the increasing disk velocity leads to increasing disk acceleration and this might affect the tribocharging phenomena of the slider/disk interface. We investigated the tribocurrent/voltage build-up generated in HDD, operating at increasing disk accelerations. In addition, we examined the effects with relative humidity conditions and rest time. We found that the tribocurrent/voltage was generated during pico-slider/disk interaction and its level was about $3\sim16pA$ and $0.1\sim0.3V$, respectively. Tribocurrent/voltage build-up was reduced with increasing disk acceleration. Higher humidity conditions $(75\sim80%)$ produced lower levels tribovoltage/current. Therefore, a higher tribocharge is expected at a lower disk acceleration and lower relative humidity condition. Rest time affected the charge build-up at the slider-disk interface. The degree of tribocharge build-up increased with increasing rest time.

• 대한안전경영과학회지
• /
• 제2권4호
• /
• pp.71-90
• /
• 2000

This study proposes strategical, practical guide to build up ERP system through several case studies to large company and comparative analysis of success and fail factors. Key words in paper .is in summary of previous BPR and ERP studies, try to clarify relationship between BPR and ERP, derivative seeking of practical key success factors through several real cases studies to build up ERP system which is in-house development or customization of commercial package.

• 대한기계학회논문집B
• /
• 제22권6호
• /
• pp.813-822
• /
• 1998

The microexplosion of a slurry droplet was considered to be caused by the shell formation and the following pressure build-up in the shell which would be promoted by the suppression of evaporation, subsequent superheating and heterogeneous nucleation of liquid carrier. To closely investigate the pressure build-up and the heterogeneous nucleation, a numerical model was introduced by considering the internal temperature distributions with the shell formation, suppression of evaporation and pressure build-up inside. The microexplosion time was estimated by postulating the limit of superheat for heterogeneous nucleation. The simulation yielded a reasonably good agreement with experimental results for Al/n-heptane slurry droplets under various solid loadings.

• 한국의학물리학회지:의학물리
• /
• 제16권2호
• /
• pp.77-81
• /
• 2005

표면 선량을 포함한 선량보강(build-up) 영역에 대한 깊이선량률(percentage depth dose)을 측정하는 데 있어서 적절한 측정방법을 결정하기 위해 6 MV 광자선에 대해 Atiix와 Markus 평행평판형 이온함, 원통형이온함, 그리고 다이오드 검출기를 사용하여 측정, 비교하었다. Attix 이온함에 의한 측정을 기준으로 할 때, Markus 이온함의 측정은 민조사면(open field)에서 $2\%$ 내로 일치하였으나, 오염전자가 포함된 광자선의 경우에는 최대 $3.9\%$의 차이를 보였다. 원통형 이온함과 다이오드 선량계의 경우에는 이들 검출기가 물 팬텀에 완전히 잠긴 이후부터는 오염전자가 포함된 광자선에 대해서도 각각 $1.5\%$ 혹은 $1.0\%$ 내의 정확도를 보였다. 따라서 민조사면에서 표면선량을 포함한 깊이선량률을 정확히 측정하기 위해서는 평행평판형 이온함이 추천되나, 표면에서의 정확한 선량에 특별한 관심을 두는 경우가 아니면, 원통형 이온함이나 다이오드 선량계를 이용하여 선량보강영역의 깊이선량률을 측정하는 것은 양호한 결과를 준다고 할 수 있다.