• Journal of the Korean Society of Marine Environment & Safety
• /
• v.21 no.5
• /
• pp.591-598
• /
• 2015

A hydraulic characteristics in the surf zone such as wave breaking points, wave set-down, wave set-up, wave-induced currents and run-up heights are studied using the SWASH model during Typhoon NAKRI(1412) in Haeundae Beach. Incident wave conditions is obtained from one-hourly observed wave data by KHOA and irregular wave by JONSWAP spectrum is given as an open boundary condition in the model. A Wave-induced current patterns by the SWASH model is compared with the observed currents and sediment flux patterns in that areas, the calculated maximum wave run-up heights in the model is compared with the video monitoring data, the empirical formula by Stockdon et al. and Mase. A dominant longshore currents toward the east of the beach appears due to the effect of incident wave direction and the geographical features and some rip currents occurs at the central part of the beach. The maximum wave run-up height(1.15 m) by the SWASH model shows a similar pattern with the video monitoring data(1.26 m) and the magnitude shows a similar result(1.33m) by Stockdon et al.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.23 no.4
• /
• pp.313-325
• /
• 2011

Finite element grid system using h-refinement on the Yellow Sea was constructed based on previous study (Suh, 1999b) from 14 K to 210 K and special attention was concentrated on refining the coastal zone. In grid generation, depth change between adjacent points and non-dimensional tidal wave length ratio were considered. As a result approximately a quarter of the total nodes are located nearby 5 m of shallow area. Accurate bathymetry data using 30's and ETOPO1 with open boundary conditions of 8 major tidal constituents extracted automatically from FES2004 have been applied. In tidal simulation a 3-dimensional nonlinear harmonic model was setup and tidal amplification due to changes in vertical turbulent and bottom friction were simulated. In this study not only 8 major tidal constituents but also nonlinear shallow tides $M_4,$, $MS_4$ and long period $M_f,$, $M_{sf}$ were reproduced. It is found that implication of spatial variation of friction coefficient plays a very important role in reproduction of astronomical and shallow tides which are computed by iterative computation of nonlinear terms. Also it should be considered differently with respect to tidal periods. To understand the distribution of tidal asymmetry, amplitude ratio of $M_4/M_2$ and phase differences $2g(M_2)-g(M_4)$ were calculated. Tidal distortion ratio marks up to 0.2 on the west coast showing shallow coastal characteristics and somewhat wide range of ebb-dominances in front of Mokpo area are reproduced.

• The Journal of the Acoustical Society of Korea
• /
• v.34 no.1
• /
• pp.36-45
• /
• 2015

Recently, a lot of studies have been made about the methods used to generate turbulent velocity fields stochastically in order to effectively predict broadband flow noise. Among them, the FRPM (Fast Random Particle Mesh) method which generates turbulence with specific statistical properties using turbulence kinetic energy and dissipation obtained from the steady solution of the RANS (Reynolds Averaged Navier-Stokes) equations has been successfully applied. However, the FRPM method cannot be applied to the flow noise problems involving intrinsic unsteady characteristics such as centrifugal fan. In this paper, to effectively predict the broadband noise generated by centrifugal fan, U-FRPM (unsteady FRPM) method is developed by extending the FRPM method to be combined with the unsteady numerical solutions of the unsteady RANS equations to generate the turbulence considered as broadband noise sources. Firstly, an unsteady flow field is obtained from the unsteady RANS equations through CFD (Computational Fluid Dynamics). Then, noise sources are generated using the U-FRPM method combined with acoustic analogy. Finally, the linear propagation model which is realized through BEM (Boundary Element Method) is combined with the generated sources to predict broadband noise at the listeners' position. The proposed technique is validated to compare its prediction result with the measured data.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.16 no.3
• /
• pp.157-168
• /
• 2014

From a complex systems perspective, ecohydrological systems in forests may be characterized with (1) large networks of components which give rise to complex collective behaviors, (2) sophisticated information processing, and (3) adaptation through self-organization and learning processes. In order to demonstrate such characteristics, we applied the recently proposed 'process networks' approach to a temperate deciduous forest in Gwangneung National Arboretum in Korea. The process network analysis clearly delineated the forest ecohydrological systems as the hierarchical networks of information flows and feedback loops with various time scales among different variables. Several subsystems were identified such as synoptic subsystem (SS), atmospheric boundary layer subsystem (ABLS), biophysical subsystem (BPS), and biophysicochemical subsystem (BPCS). These subsystems were assembled/disassembled through the couplings/decouplings of feedback loops to form/deform newly aggregated subsystems (e.g., regional subsystem) - an evidence for self-organizing processes of a complex system. Our results imply that, despite natural and human disturbances, ecosystems grow and develop through self-organization while maintaining dynamic equilibrium, thereby continuously adapting to environmental changes. Ecosystem integrity is preserved when the system's self-organizing processes are preserved, something that happens naturally if we maintain the context for self-organization. From this perspective, the process networks approach makes sense.

• Korean Journal of Materials Research
• /
• v.11 no.6
• /
• pp.512-518
• /
• 2001

It has been well known that 6.5wt% Si steel sheets have excellent magnetic properties such as low core loss. high maximum permeability and low magnetostriction. In this work, we studied a method for producing 6.5wt% Si steel sheets using a chemical vapor deposition (CVD) method. The following is the procedure adopted in this work to produce 6.5wt% Si steel sheets; SiCl$_4$ gas is applied onto a low content-Si steel sheet placed in a tube furnace. Silicon atoms resulted from the decomposition of SiCl$_4$ are permeated through the surface of the steel sheet. Finally, by the diffusion process maintaining it under a high temperature the silicon atoms diffuse uniformly into the sheet. Through this process, 6.5wt% Si steel sheets can be obtained. The manufactured Fe-6.5wt% Si steel sheet with a thickness of 0.5mm exhibited a high frequency core loss (W$_{2}$1k/) of 8.92 W/kg. Its permeability increased from 37,100 to 53,300 at 1 tesular(T). The mechanical properties of the manufactured steel sheets were also estimated and the result showed that the workability was significantly improved by annealing in vacuum at 773k. Increased plastic deformation was also observed prior to fracture and the amount of grain boundary rupture was reduced.

• Journal of the Economic Geographical Society of Korea
• /
• v.12 no.4
• /
• pp.521-539
• /
• 2009

This study investigates the time-space characteristics of the road traffic flows in Seoul and the relationship with land use patterns. For the purpose, we analyze the road traffic data collected at 118 observation sites over Seoul City area since 1993. We examine the time-trend of the annual average traffic flows per day during the last fourteen years. Three different trends are revealed: rapid increase during the time period between 1993 and 1997, maintenance same level after sharp decrease between year 1997 and 1998, and gradual decrease after sharp decrease between year 2003 and 2004. The spatial distribution patterns of road traffic flows have also been changed significantly during the period. The traffic flows in the urban center have been declined gradually, while the traffic flows in the boundary area and southern CBDs have increased dramatically. In order to examine the relationship with the changes in the land-use patterns and road traffic flows, we analyze the changes in the spatial distribution patterns of population and industries. We developed three multiple linear regression models to test the relationships between the changes in the land-use variables and road traffic flows.

• Journal of Korean Society of Forest Science
• /
• v.106 no.1
• /
• pp.100-109
• /
• 2017

This study was conducted for preliminary survey and management support for Pine Wood Nematode (PWN) suppression. We took areal photographs of 6 areas for a total of 2,284 ha during 2 weeks period from 15/02/2016, and produced 6 ortho-images with a high resolution of 12 cm GSD (Ground Sample Distance). Initially we classified 423 trees suspected for PWN infection based on the ortho-images. However, low accuracy was observed due to the problems of seasonal characteristics of aerial photographing and variation of forest stands. Therefore, we narrowed down 231 trees out of the 423 trees based on the initial classification, snap photos, and flight information; produced thematic maps; conducted field survey using GNSS; and detected 23 trees for PWN infection that was confirmed by ground sampling and laboratory analysis. The infected trees consisted of 14 broad-leaf trees, 5 pine trees (2 Pinus rigida), and 4 other conifers, showing PWN infection occurred regardless of tree species. It took 6 days for 2.3 men from to start taking areal photos using UAV (Unmanned Aerial Vehicle) to finish detecting PNW (Pine Wood Nematode) infected tress for over 2,200 ha, indicating relatively high efficacy.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.17 no.2
• /
• pp.81-89
• /
• 2014

The present study aims to design an optimized hull shape of a floating pendulum-type wave energy converter(WEC). The purpose of these structure is to improve the performance and stability of the WEC by reducing its motion under operating and survival wave conditions. In this study, motion reduction structures, like restoring and dampling plates were installed on a floating pendulum WEC that has been the subject of previous studies. Restoring plates were installed to increase the restoring force and shift the natural period to a shorter period. Damping plates were installed to shift the natural period to a longer period by increasing the added mass. The effects of the structures were then analyzed under different incident wave conditions. The design parameters for the motion reduction structures were size, shape, and installed position. The wave-induced motion characteristics and performance of the floating pendulum WEC were also investigated numerically. Based on the simulation results, we are able to optimize the motion reduction structure of the WEC, thus improving its efficiency and durability.

• Journal of Conservation Science
• /
• v.6 no.1 s.7
• /
• pp.61-70
• /
• 1997

An integrated geophysical survey was conducted to study a construction method of the Sonsanri tombs including the Muryong royal tomb. With the distribution of soil resistivity and self potential values, the boundary between original ground and the construction site was delineated clearly. The original ground has relatively high resistivity of $1,000\~1,500$ ohm-m and low self-potential values of $0{\pm}3mV/m$, while the construction site has low resistivity less than 200 ohm-m and quite high self-potential values of $-20\~30mV/m$. It is interpreted that the open site for construction of subsurface tomb has the size of about 35 m in the north-south direction. Big difference in characteristics of ground between the tomb site and the original site gives a clue for the construction method of tombs in Baekje dynasty. The site was opened about 35 meters in the north-south direction and then a mold structure was constructed with a brick frame outside. The brick frame consists of bricks cemented each other and structually combined. The mold structure was removed from inside after refill of the opened construction site with some cemented rock debris and soil.

• Journal of Conservation Science
• /
• v.28 no.4
• /
• pp.343-351
• /
• 2012

Excavated archaeological iron objects are prevented from being corroded going through desalination which slow down being corroded. However archaeological iron objects are liable to be corroded due to the high ionization tendency even though they are stored in environment restricted from corrosion factors. Iron objects could be deteriorated more than just excavated. Therefore this study investigated about the characteristic of re-corrosion and the effect on objects. In study, archaeological iron nails in storage for 4 years after conservation treatments were tested. Optical microscopy and X-ray photography for appearance, XRD, SEM-EDS, Raman spectroscopy for chemical composition, IC for chloride ions concentration inside iron nails were used. As results, iron nails carried out conservation treatments measured a high concentration of chloride ions after the long storage period. The form of objects were not in good condition such as broken or destroyed when the high chloride ions concentration was detected. In addition, the yellow and red powdery corrosion product were detected on the boundary between corrosion products and substrates and they were identified as akaganeite which is symptom of active corrosion.