• Korean Journal of Agricultural Science
• /
• v.3 no.1
• /
• pp.95-104
• /
• 1976

This study was conducted to test the harvesting operation of two kinds of rice varieties such as Milyang #15 and Tong-il with a imported two furrow Japanese combine and was performed to find out the operational accuracy of it, the adaptability of this machine, and the feasibility of supplying this machine to rural area in Korea. The results obtained in this study are summarized as follows; 1. The harvesting test of the Milyang #15 was carried out 5 times from the optimum harvesting operation was good regardless of its maturity. The field grain loss ratio and the rate of unthreshed paddy were all about 1 percent. 2. The field grain loss of Tong-il harvested was increased from 5.13% to 10.34% along its maturity as shown in Fig 1. In considering this, it was needed that the combine mechanism should be improved mechanically for harvesting of Tong-il rice variety. 3. The rate of unthreshed paddy of Tong-il rice variety of which stem was short was average 1.6 percent, because the sample combine used in this study was developed on basisof the long stem variety in Japan, therefore some ears owing to the uneven stem of Tong-il rice could nat reach the teeth of the threshing drum. 4. The cracking rates of brown rice depending mostly upon the revolution speed of the threshing drum(240-350 rpm) in harvesting of Tong-il and Milyang #15 were all below 1 percent, and there was no significance between two varieties. 5. Since the ears of Tong-il rice variety covered with its leaves, a lots of trashes was produced, especially when threshed in raw materials, and the cleaning and the trashout mechanisms were clogged with those trashes very often, and so these two mechanisms were needed for being improved. 6. The sample combine of which track pressure was $0.19kg/cm^2$ could drive on the soft ground of which sinking was even 25cm as shown in Fig 3. But in considering the reaping height adjustment, 5cm sinking may be afford to drive the combine on the irregular sinking level ground without any readjustment of the resaping height. 7. The harvesting expenses per ha. by the sample combine of which annual coverage area is 4.7 ha. under conditions that the yearly workable days is 40, percentage of days being good for harvesting operation is 60%, field efficiency is 56%, working speed is 0.273m/sec, and daily workable hours is 8 hrs is reasonable to spread this combine to rural area in Korea, comparing to the expenses by the conventional harvesting expenses, if mechanical improvement is supplemented so as to harvest Tong-il rice. 8. In order to harvest Tong-il rice, the two furrow combine should be needed some mechanical improvements that divider can control not to touch ears of paddy, the space between the feeding chain and the thrshing drum is reduced, trash treatment apparatus must be improved, fore and rear adjust-interval is enlarged, and width of track must be enlarged so as to drive on the soft ground.

• Journal of Chest Surgery
• /
• v.43 no.6
• /
• pp.602-613
• /
• 2010

Background: As life expectancy has been increased, the cardiac valve disease has been increased. In past, mechanical valve for valve replacement surgery was used widely, but it has many weaknesses, such as hemorrhage, teratogenic effect caused by warfarin, acute mechanical failure, taking warfarin during life, etc. So, the tissue valve is used widely and researches for durability of tissue valve are in progress. Tissue valves being used are all imported in Korea, and there is a lack of information on its geometry and design. So, we studied the geometry of porcine aortic and pulmonary valve, and tried to suggest theoretical basis for making the aortic and pulmonary valve. Material and Method: We harvested aortic and pulmonary valves of 25 pigs and measured the geometry of valve at fresh and glutaraldehyde (GA) fixed state. In each group, we measured the diameter of the base, diameter of commissure, valve height, commissural height, etc. Also, for making implantable porcine and bovine pericardial valve, we designed the valve stent form, thickness, height, and leaflet size, form, thickness by different size of valve. Result: The aortic and pulmonary valve geometry and ratio were measured in each group. The right coronary cusp of aortic valve and right facing cusp of pulmonary valve was bigger than other cusps and non coronary cusp was smaller than others (RCC: NCC : LCC=1 : 0.88 : 1). Valve height was correlated to the leaflet size. We designed the outer diameter of stented porcine aortic valve from 19 mm to 33 mm and designed stent height and width, using previous measured ratio of each structure, stent thickness, working thickness (for making valve). Also, we designed the size of stent and form for stented bovine pericardial valve, considering diameter of valve, leaflet length, height and leaflet minimum coaptation area. Conclusion: By measuring of 25 pig's aortic and pulmonary valve geometry and ratio, we can make theoretical basis for making implantable stented porcine valve and bovine pericardial valve in various size. After making implantable valve using these data, it is necessary to do in vivo and in vitro researches, furthermore.

• Journal of Life Science
• /
• v.25 no.11
• /
• pp.1280-1289
• /
• 2015

Fish-meat gel is being produced mostly relying on surimi and raw materials imported from Southeast Asia and North America and present in small amount in local markets. In this study, common farmed local fishes were examined as stable and reliable sources of surimi for fish-meat gel production. For testing, five main farmed-fish of Korea, namely; Bastard halibut (Paralichthys olivaceus), Red sea bream (Pagrus major), Korean rockfish (Sebastes schlegeli), Common mulle (Mugil cephalus), and Finespotted flounder (Pleuronichthys cornutus) were used following a traditional washing process. The quality of the surimi was determined by the values of water content, whiteness index, gel strength and impurity. Accordingly, fish-meat gel and surimi quality experiments were carried out by measuring compressive and texture properties, expressible moisture content, Hunter color scale values and SDS-page protein patterns. Also gel characteristics were compared with that of FA and RA grade surimi (Alaska Pollock). Fish-meat gels were prepared by salt mincing the farmed-fish surimi with NaCl (2% w/w) and moisture adjustment to 84% by ice water adding. Prepared fish-meat paste was filled into 20-25 cm long polyvinylidene chloride casings and heated at 90℃ for 20 min. The whiteness values of fish-meat gels produced from surimi were increased by using farmed-fish and became comparable to that of FA Alaska Pollock gel. Among all tested farmed-fish, P. olivaceus and P. major exhibited better properties than RA Alaska Pollock and similar properties to FA Alaska Pollock. Therefore, current data suggests that fish farming can be an efficient and sustainable fish-meat source for fish-meat gel production in Korea.

• Journal of Korea Port Economic Association
• /
• v.30 no.3
• /
• pp.163-185
• /
• 2014

The growth of a city requires substantial resources, an appropriate environment, and the alignment of several factors. City growth also evolves through changes in its history, culture, economics, societies, groups, and government systems. However, current port city development plans designed to encourage the growth of local businesses fail to provide the support needed for both the city and businesses. The recent actions of urban administrations and federal and local governments have revealed that they have yet to create a mature decentralized management system, or perhaps have ignored the reality of needing one. Taking a clear look at the differences between port regions, such as Gwangyang and Pyeongtaek, and understanding their effect on city growth would be a prudent course of action when preparing for future developments. The purpose of this study is to determine the relationship between ports and cities by analyzing the effect of port characteristics on nearby city growth. This study used a comparison analysis to determine how port characteristics affected the growth of Pyeongtaek and Gwangyang. One result of this analysis showed that an increase in the number of goods being imported or exported had a positive effect on the growth of both port cities, In this respect, an aggressive plan and cooperation between the federal and local government should occur simultaneously. Furthermore, efficient local policies that focus on the increase of personnel and material resources should be pursued as a standard strategy, which would also promote the international status of these locations. The results of this study show the importance of government cooperation. The federal government should lead with aggressive strategies that aim to optimize efficiency, while the local government should provide the necessary assistance and coordination in order to achieve optimal results.

• Korean Journal of Social Welfare
• /
• v.57 no.3
• /
• pp.5-30
• /
• 2005

Globalization has conflicting effects on pharmaceutical policies. A change into a 'populist competitive nation' due to globalization strengthens policies to reduce drug manufacturing costs while the WTO's TRIPS Agreement that is affected by multinational pharmaceutical companies increases drug manufacturing costs by bolstering the patent rights on new drugs. Currently, the independency of populist nations' policies to reduce drug manufacturing cost is being compromised because multinational organizations(such as the European Union) which represents the interests of the multinational pharmaceutical companies put restrictions on the pharmaceutical policies of populist nations for purposes of promoting the industrial goals of the multinational companies. Korea is no exception. Up until the late 1990s, the main feature of the pharmaceutical policies in Korea was keeping the drug price at the cost level based on a growth-driven ideology, and this was Korea's unique policy tools as a developing nation. However, the increase in the power of multinational pharmaceutical companies currently infringes on the independency of Korea's pharmaceutical policies. Expensive imported drugs were originally covered by the national health insurance plan, but starting from 1999 such drugs began to be covered by the plan. After separation of medical and pharmaceutical services, the use of expensive drugs was increased, and the Korean government planned to introduce the reference price policy in order to contain the cost of the national health insurance plan. However, due to pressures from the U.S. government as well as multinational pharmaceutical companies, implementation of the policy has been postponed. In addition, due to a pressure from the U.S. government, a working group was created which would affect the health care policy of the Korean government. Discussions so far on globalization was about whether the change into populist competitive nations due to globalization resulted in the reduction of welfare spending. However, this study shows not only the reduction of health care cost through policies to reduce drug manufacturing costs but increase in welfare spending by raising the strengths of multinational pharmaceutical companies that are for-profit providers of welfare service. While focusing on the contradictory effects of globalization on pharmaceutical policies of a nation, this study looked at how these conflicting effects end up promoting the interests of multinational pharmaceutical companies by examining the Korean case.

• Korean Journal of Agricultural Science
• /
• v.12 no.1
• /
• pp.101-107
• /
• 1985

Since most farmers breeding livestocks in Korea is depended on imported feeds, the rate of self-supplying feeds is very important for a stable development of farmers. Therefore, it is considered necessary to increase the rate of self-supplying feeds. In this study, performance tests were carried out with barley and forage to find the design's parameters of hammer for a small size hammer mill which can be driven by 3.7-7.5 kW power tiller being used by most farmers. The revolution speed of hammer mill was 3000 rpm, widths of hammer were 20mm, 30mm, 40mm, and the levels of thickness of hammer were 2mm, 4mm and 6mm. Experimental materials used were barley and forage and screen openings for barley was 4.76mm, and 3.18mm for forage. The study results can be summarized as follows; 1. Results of grinding tests showed that particle sizes were 478-774 microns for barley and 350-434 microns for forage. They were decreased according to the increasing thickness and width of hammer. 2. Fineness modulus of grinded materials were 3.07-3.62 for barley and 2.69-2.93 for forage. They were inversely proportional to thickness and width of hammer. 3. The required power for grinding was 3.8-5.0 kW for barley and 0.9-1.4 kW for forage. The thickness of hammer was more important for less power requirement than width of hammer. 4. Grinding performance of a small size hammer mill was 99-170kg/kWh for barley and 11-21 kg/kWh for forage. The thickness of hammer was an important factor for grinding performance, and inversely proportional to grinding performance. For about 3.2 of fineness modulus, 4 mm thickness was the best, and an optimum width of hammer was 30mm for a small size hammer mill.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.40 no.3
• /
• pp.81-90
• /
• 2012

Improvements in the quality of life have resulted in a heightened awareness of safety and the environment. As a result, timber as an environmentally friendly material, is used for landscape facilities and a wide range of purposes. But there are a large number of defects since there are twists and cracks that can be found in wooden landscape facilities. This has led to the use of imported hardwood instead of the Western Hemlock which has been in widespread use. Hardwood is expensive. However, it is being used without any information or research on how much it reduces the actual defects. Construction contractors are in great need of information on the characteristics and defect rates of different types of timber. This study investigated and analyzed the cracks in four types of timber - namely the Western Hemlock, Burckella, Nyatoh and Malas - in order to provide basic information to construction contractor for them to be able to select and use the appropriate type of timber. The main results of this study are as follows. First, the Western Hemlock had 1.90 $cracks/m^2$, Malas had 0.83 $cracks/m^2$, Burckella had 0.14 $cracks/m^2$, and the Nyatoh had the least number of surface defects at 0.04 $cracks/m^2$. Second, while Malas has the highest degree of strength timber, Nyatoh had the smallest defect rate. This showed that having high timber strength does not necessarily mean it has less defects. Third, the Western Hemlock was the least expensive and Burckella was the most expensive. However, considering the cost of repairing defects, it would be economically advantageous to use Burckella and Nyatoh which have low defect rates. This study aimed to provide basic information to landscape construction contractors for them to be able to select and use the appropriate type of timber when constructing wooden outdoor rest furniture. The results are expected to contribute to quality enhancements and defect reduction in landscape facilities.

• Archives of design research
• /
• v.19 no.2 s.64
• /
• pp.73-80
• /
• 2006

The main purpose of this study is to help develop the productional system of the three dimensional digital animation domestically. Many 30 digital animation projects are being developed and finished with foreign computer graphics technology. However, the 3D animation market in Korea is not as good as the ones in other countries. One of the most significant problems is the lack of a program of study in Korea concerning productional systems used to create 3D animation. We previously imported an advanced productional system from the U.S., which was adaptable to big projects, and consequently, expanded the international digital animation market. Now, we need to develop a new production system which is fully adaptable to the Korean market. A non-sequential system of 3D digital animation tailored for small projects is more adaptable to domestic industry than the sequential system known as the 'Pipeline system.' A non-sequential system is good for small productions that are trying to create animation on a limited budget. The workers in this system can learn to make animation fast and effectively. They can also learn how to discuss with the others in order to avoid duplication of action. In contrast, in the Pipeline System, many workers repeat confirmation steps during the process for the same animations. The benefit of the non-sequential system is that the worker's interest and education can speed up production, because he/she can quickly learn every step of the animation process instead of just doing a particular job which does not allow him/her to observe the other steps involved. The 'animatic' step is the most important in the non-sequential system. The final animation is produced from the animatic. It is developed from scratch through to the final product but only after the agreement of all the workers, including a director.

• Korean Journal of Heritage: History & Science
• /
• v.53 no.2
• /
• pp.64-87
• /
• 2020

Copper trihydroxychloride (atacamite, botallackite, paratacamite, etc.), the first green pigment used in Mogao Grotto's mural paintings of China, has been known as "copper green", "green salt", and "salt green", etc. and has been used as an important green pigment with malachite. At first, the natural mineral atacamite was employed, but after the Five Dynasties (907~960 CE), synthetic copper trihydroxychloride was primarily used. In Chinese literature, copper green, green salt, and salt green are recorded as being made via reaction with copper powder, Gwangmyeongyeom (natural sodium chloride), and Yosa (natural ammonium chloride), and the prepared material was analyzed to be copper trihydroxychloride. Copper trihydroxychloride pigment was not found in paintings prior to the Joseon Dynasty (1392~1910 CE) in Korea. In analysis of the green pigments used in paintings and the architectural paintworks in the Joseon Dynasty, copper trihydroxychloride was also shown to have been used as an important green pigment with malachite (Seokrok). In particular, the proportion of copper trihydroxychloride use was high in Buddhist paintings, shamanic paintings, and dancheongs (decorative coloring on wooden buildings). Some of these turned out to be synthetic copper trihydroxychloride, but it is unclear whether the rest of them are synthetic or natural pigments due to a lack of analyzed data. From literature and painting analyses, the pigment name of copper trihydroxychloride in the Joseon Dynasty turns out to be Hayeob, a dark green pigment. It is believed to have first been prepared by learning from China in the early Joseon period (early 15^th century) and its use continued until the late 19^th century with imported Chinese pigment. Round or oval particles with a dark core of copper trihydroxychloride which were used in Chinese literature were similar to the synthetic copper trihydroxychloride pigments used in the Joseon Dynasty and Chinese paintings. Therefore, the synthetic copper trihydroxychloride pigments of Korea and China are believed to have been prepared in a similar way.

• Korean Journal of Heritage: History & Science
• /
• v.38
• /
• pp.387-419
• /
• 2005

Material characteristics and provenance interpretation of the raw materials for the stone moulds of bronze artifacts excavated in Galdong Prehistoric site were studied. The stone moulds are made of igneous hornblendite with coarse-grained holocrystalline textures. The surface color shows greenish grey to dark green with greasy luster. The value of magnetic susceptibility of the moulds ranges from 19.2 to 71.0 (mean ; $39.2{\times}10^{-3}$ SI unit).High value of magnetic susceptibility indicates high contents of magnetite as a ferromagnetic mineral and the wide range of the values are due to heterogeneous distribution of magnetite. These are characteristics of basic igneous rocks. The rock-forming minerals of the moulds mainly consist of amphibole, plagioclase and biotite. Pyroxene, chlorite and opaque minerals are also rarely present. A large quantity of carbon was detected on the dark black crust near the surface of the moulds by quantitative analysis. Geological field survey was carried out to identify a source of the raw materials of the stone moulds around Galdong site. Hornblendite or gabbroic rocks being similar to the moulds forming rock occur at Daeseongri, Sikcheonri and Gyodongri in Jangsoo, and Illdaeri in Namwon about 50 kilometers away from the site in a straight line. They have similarity with the moulds forming rock in magnetic susceptibility ranging from 16.1 to 72.4 (mean ; $39.9{\times}10^{-3}$ SI unit). Among those hornblendite or gabbroic rocks, one in Jangsoo area is the most similar to the moulds forming rock on the basis of petrological and mineralogical characteristics. Comparing normalized patterns of major, minor, rare earth and immobile elements contents of the moulds to them of hornblendite in Jangsoo area, geochemical evolution trend and behavior characteristics show affinities between them. It suggests that the moulds forming rock and hornblendite in Jangsoo area have been originated from cogenetic magma. This hornblendite is easy to engrave an inscription or detail graphics on the surface because of its softness, and has good thermal conductivity. Hornblendite in Sikcheonri, Jangsoo is particularly produced and used for stone wares until the present day. Therefore, it is probable that the stone materials of the moulds has been imported from Daeseongri, Sikcheonri and Gyodongri in Jangsoo area. However, it cannot be completely excluded the possibility that the material of the moulds was supplied from Illdaeri in Namwon area appearing the same type of hornblendite on a small outcrops. It is necessary to carry out further archaeological studies to identify several possibilities of migration process of raw materials.