• Journal of the Korea Institute of Military Science and Technology
• /
• v.6 no.3
• /
• pp.36-43
• /
• 2003

Multi-target away signal simulator which can simulate the radiated noises of maneuvering targets in a specified ocean range is an essential equipment for the validation of developed towed array sonar system. This simulator should provide realistic multi-channel signals those are required for beamforming on the signal processing unit of towed away system. This paper describes the overall system configuration and signal synthesis techniques for the target radiated noise. And this paper considers why the time delays between target and individual sensors are caused and how to compensate these time delays to individual sensors output. This multi-purpose target simulator could be used for the training of TASS operators.

• Journal of Information Processing Systems
• /
• v.16 no.6
• /
• pp.1271-1280
• /
• 2020

The yield and quality of a micromanufacturing process are important management factors. In real-world situations, it is difficult to achieve a high yield from a manufacturing process because the products are produced through multiple nanoscale manufacturing processes. Therefore, it is necessary to identify the processes and equipment that lead to low yields. This paper proposes an analytical method to identify the processes and equipment that cause a defect in the plastic ball grid array (PBGA) during the manufacturing process using logistic regression and stepwise variable selection. The proposed method was tested with the lot trace records of a real work site. The records included the sequence of equipment that the lot had passed through and the number of faults of each type in the lot. We demonstrated that the test results reflect the real situation in a PBGA manufacturing process, and the major equipment parameters were then controlled to confirm the improvement in yield; the yield improved by approximately 20%.

• The Journal of the Acoustical Society of Korea
• /
• v.21 no.5
• /
• pp.478-484
• /
• 2002

Linear towed arrays (LTA) have a nonlinear shape due to tow vessel motion, ocean swells and currents. By reasons of nominally linear shape, various towed array shape estimation techniques have been developed since the perturbed shape cause the error in target detection. In this paper,, we propose the beamforming method for the perturbed LTA with simple structure. The proposed method linearizes a nonlinear phase of steering vector with position information measured by two reference sensors. It can be proved using some properties of Markov transition matrix, and iteration number of linearization process is decided by variance of cross phase difference. As a result of computer simulation in the ocean environment, beampattern of the proposed method is almost same with the ideal case in my type of array shape. In the signal-to-noise ratio (SNR) performance simlation, the DOA estimation performance of the proposed beamforming method is evaluated, and the comparison with Bartlett beamformer of the LTA shows that the proposed method can estimate. the spatial characteristic of sources more accuracy.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.6A
• /
• pp.900-909
• /
• 2000

Adaptive array antennas are one of the most promising techniques for improving the capacity of CDMA mobile communication system. In this paper, the uplink and downlink capacity for asynchronous W-CDMA system with adaptive array antenna is analyzed when an angle estimation error is present. From the results, it is found that the capacities are decreased by the angle estimation error. Specifically, when 5 degrees of error is present at 9 element adaptive array, the capacities are found to decrease by 5.2% in the uplink and 11.6% in the downlink. Also, in this paper, an attempt for comparing the capacities on different channel environments has been made. However, it is found that the increase of the Rice factor hardly effects the capacity due to the power control.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.3
• /
• pp.410-424
• /
• 1993

In this paper, we present new techniques for designing systolic arrya and asynchronous arrays for digital-signal processings. More specifically, we propose a systolic array with simple local interconnections which achieves optimal performance without having undesirable features such as preloading input data or global broadcasting. As asynchronous array for digital-signal processings, which can speed up the total computation time significantly is also which can speed up the total computation time significantly is also presented. The key component of the asynchronous array is a presented. The key component of the asynchronous array is a comunicaiton protocol which controls input data flow properly and efficiently. Finally, performance of the arrays is analyzed and a simulation using Occam programmed in a Transputer network is reported.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.8C
• /
• pp.745-757
• /
• 2007

In this paper, we propose a design of GPS anti-jamming system and its operational method, which can effectively suppress interference and jamming signals induced in GPS receiver. The 7-array antenna used in the proposed system is composed of conventional 6 equi-spaced circular elements with one element on the center of antenna and can be efficiently operated under power-constrained conditions. Futhermore, in this paper, we analyze the structure and complexity of STAP and SFAP which are well known techniques in adaptive array antenna signal processing, and we compare the BER performances between STAP and SFAP in various jamming environment based on the same complexity.

• Journal of the Korean Society of Safety
• /
• v.18 no.4
• /
• pp.98-104
• /
• 2003

Various nondestructive evaluation (NDE) techniques have been studied to locate steel rebars of dowel, and to detect invisible damage such as voids and cracks inside concrete and debonding between rebars and concrete caused by corrosions and earthquakes. In this study, the aurhors developed 3-dimensional (3D) electromagnetic (EM) imaging technology to detect such damage and to identify exact location of steel rebars of dowel. The authors have developed sub-surface two-dimensional (2D) imaging technique using tomographic antenna array in previous works. In this study, extending the earlier analytical and experimental works on 2D image reconstruction, a 3D microwave imaging system using tomographic antenna array was developed, and multi-frequency technique was applied to improve quality of the reconstructed image and to reduce background noises. This paper presents the analytical expressions of numerical focusing procedures for 3D image reconstruction and numerical simulation to study the resolution of the system and the effectiveness of multi-frequency technique. Also, the design of 4?4 antenna array with switching devices is introduced as a preliminary study for the final design of whole array.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.8
• /
• pp.1598-1603
• /
• 2003

A microstrip array antenna is designed and tested for satellite broadcasting receptions. The Sierpinski equilateral triangular patch and SSFIP(slot­strip­foam­inverted patch) structures are used. The Sierpinski geometry is composed of 3 equilateral triangular patch and is easy to generate a circular polarization by sequential rotation array techniques. This 1${\times}$3 Sierpinski equilateral triangular patch antenna is extended to 8${\times}$2 array antenna for satellite broadcasting receptions. The measurement results of the reflection coefficients and the radiation patterns of the manufactured array antenna show good agreements with the simulation results.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.6
• /
• pp.550-557
• /
• 2008

Delamination damage at a bolt hole in a composite stiffened panel was detected using a built-in piezoelectric active sensor array. Various signal processing techniques were used to detect an invisible small scale delamination around a fastener hole due to localized transverse loading. A built-in piezoelectric sensor array was used to generate diagnostic signals and to measure response signals. Then, the response signals were processed to extract damage-sensitive features. Damage indexes were calculated to estimate the severity and location of the damage from the features.

• International Journal of CAD/CAM
• /
• v.3 no.1_2
• /
• pp.111-117
• /
• 2003

The paper presents an efficient algorithm based on ROAM for visualization of large scale terrain models in real-time. The quality and smoothness of the terrain data visualization within a 3D interactive environment is preserved, while the complexity of the algorithm is kept on a reasonable level. The main contribution of the paper is an introduction of a number of efficient techniques such as implicit coordinates method within the patch array representing ROAM and the viewpoint dependent triangle rendering method for dynamic level of detail (LOD) updates. In addition, the paper presents experimental comparison of a variety of culling techniques, including a newly introduced method: relational position culling. These techniques are incorporated in the visualization software, which allows to achieve more realistic terrain representation and the real-time level of detail reduction.