• 한국입자에어로졸학회지
• /
• 제15권2호
• /
• pp.67-78
• /
• 2019

Since existing measurement sites are required to construct a high-cost PM measuring device and a measuring site of a large area, there is a limit to the construction of a high-resolution measurement network. Therefore, it is necessary to develop a low-cost, high-performance PM measuring device (as an alternative technology) that can increase the resolution of PM measurement, and it is necessary to establish a base to provide real-time PM information for whole people. Therefore, in this study, the alternative technique (light scattering method) for achieving the above object was examined, performance evaluation was carried out, and it was verified that the light scattering method was usable. Various PM measurement results were compared and analyzed to find PM monitoring points and resolutions we would like to propose.

• Journal of the Korean Wood Science and Technology
• /
• 제49권3호
• /
• pp.274-282
• /
• 2021

Transparent and colorless melamine-urea-formaldehyde (MUF) resins make it difficult to identify the area of wood failure percentage (WFP) in the fracture surface of bonded wood specimens. Therefore, in this study, we develop a method of measuring WFP after the adhesion strength measurement of MUF resins under shear stress. The fractured wood surface of b lock shear strength (BSS) specimens bonded with cold-setting MUF resins at three melamine contents (20%, 30%, and 40%) was marked black, and then, WFP was accurately measured via image analysis. WFP values measured using this method consistently increased with BSS as the melamine content increased, showing the reliability of this new method. The results suggested that this new method is useful and reliable for measuring the WFP of the fracture surface of wood specimens bonded with colorless adhesives such as urea-formaldehyde, MUF, and melamine-formaldehyde resins.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.939-943
• /
• 2004

The side and rear-side collision warning system using fuzzy control algorithms is discussed in this paper. Common rearside warning system has many problems. For example if target vehicle comes into the warning area, it must unconditionally warn. Drivers could be interrupted by it. To solve the problem, I divided measuring area into two sections. One section is blind area of vehicle and the other rear-side area. For blind area, obtained data was filtered inefficient warning signal by using relative velocity method. For rear-side area, a fuzzy logic algorithm is used to recognition of obstacles. According to our experiment relative velocity method and fuzzy logic algorithms were very efficient.

• 한국정밀공학회지
• /
• 제24권2호
• /
• pp.73-85
• /
• 2007

The rear lateral collision warning system using fuzzy control algorithms is discussed in this paper. Common rear lateral warning system has many problems. For example if target vehicle comes into the warning area, it must unconditionally warn. Drivers could be interrupted by it. To solve the problem, I divided measuring area into two sections. One section is blind area of vehicle and the other rear lateral area. For blind area, obtained data was filtered inefficient warning signal by using relative velocity method. For rear lateral area, a fuzzy logic algorithm is used to recognition of obstacles. According to our experiment relative velocity method and fuzzy logic algorithms were very efficient.

• 지질공학
• /
• 제18권1호
• /
• pp.7-16
• /
• 2008

석회암지역은 외부의 압력에 의한 파쇄대와 용해성공동 등과 같은 지질학적인 결함을 대부분 갖고 있다. 특히, 장대교량을 건설할 경우 지질학적인 결함을 갖고 있는 석회암공동의 처리는 꼭 필요하다. 석회암 공동에서 기초의 침하량을 줄이고 지반을 보강하기 위한 대책공법으로 고압분사주입공법이 많이 활용되고 있다. 그러나 고압분사주입공법은 석회암공동에 대한 보강공법으로 활용되어 왔으나 연구실적과 기술적인 자료의 축적이 부족한 편이다. 그러므로 본 논문은 고압분사주입공법에 의하여 보강된 석회암공동 구간에 대하여 강도특성과 변형특성에 대한 연구결과를 제시하였다. 그리고 하중전이시험이 수반된 정재하시험에 의하여 지지력특성도 논의하였다.

• 한국컴퓨터정보학회논문지
• /
• 제16권2호
• /
• pp.55-60
• /
• 2011

본 논문에서는 요부 영상에서 근육을 추출하는 방법을 제안한다. 제안된 방법은 초음파 영상에서 왜곡이 존재하지 않는 영역을 측정할 근육 영역으로 설정한 후, 초기 초음파 영상에서 불필요한 잡음을 제거하고 Ends-in Search Stretching 기법을 적용하여 근육 영역의 명암 대비를 강조한다. 그리고 형태학적 특징을 이용하여 등뼈 영역과 피하지방을 분리한 후, 4 방향 윤곽선 추적 알고리즘을 적용하여 피하지방의 하단 부분을 추출한다. 또한 최대 및 최소 명암도를 조정하여 얻어진 등뼈의 후보 영역에서 형태학적 특징을 이용하여 잡음을 제거하고 최종적으로 등뼈 영역을 추출한다. 추출된 등뼈 영역을 기반으로 피하지방층과 등뼈 사이를 근육의 두께로 측정한다. 본 연구에서 제안된 방법을 368개의 요부 초음파 영상에 적용하여 근육 영역을 추출한 결과, 제안된 방법이 초음파 영상에서 근육 영역들의 두께를 측정하는데 기존의 근육 측정 방법보다 효과적인 것을 확인할 수 있었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 학술회의 논문집 정보 및 제어부문 B
• /
• pp.1018-1021
• /
• 2003

This dissertation is reference to measure visual information about the configuration of magnetic field automatically and materialize the new magnetic field mapping system for the rapid and clear measure by using of the mediocrity orthogonal robot in the three- dimensional space required the measure of magnetic field concurrently. The measuring sensor is composed to be available for the measure of three-dimensional direction of magnetic field by vertically conjoining each of three hall sensors utilized of the hall effect and installed Gaussmeter, which is devised to receive the sensor result and the robot controller, away from the measuring robot in order to minimize the affection of magnetic field. Also, the controller and Gaussmeter are composed of Use interface, RS-232C and IEEE-488.2 communication. Interface system is written in NI's LabVIEW and composed to be able to set up a measuring area, the measuring number of times, two and three-dimensional graph, the velocity of robot and the magnetic field distribution graph of each element by inputting parameters. The materialized magnetic field mapping system expert the collection of the data easily and the effect of utilizing data.

• 한국재난정보학회 논문집
• /
• 제20권1호
• /
• pp.147-155
• /
• 2024

연구목적: 본 연구는 재난 안전 사각지대에 있는 소규모의 민간 건축물을 대상으로 건축물의 위험징후를 분석하고 계측기술을 개발하기 위한 건축물 모니터링 시스템 설치 방안을 제시하는 것을 목적으로 한다. 연구방법: 건축물 위험거동의 원인, 모니터링 계측 기기의 구성요소, 계측기기 설치 위치, 관리 방안 등을 제시한다. 연구결과: 계측기기는 필수적으로 가속도센서, 기울기센서, 자이로센서, GPS 등이 포함된다. 계측장치는 기둥의 높이와 단면적을 고려해야 한다. 결론: 본 연구의 결과는 소규모 민간 건축물에서 발생할 수 있는 건축물 붕괴로부터 발생하는 재난을 대비하여 재난 안전 역량 강화를 할 수 있다.

• 정보통신설비학회논문지
• /
• 제2권1호
• /
• pp.78-87
• /
• 2003

One of the most difficult and important problems associated with radiated electromagnetic emissions from digital devices are the determination of antenna factor and site acceptability of an open area test site. This paper presents the problems of the open area test site and EMC antennas far measuring electromagnetic interferences radiated from the equipements. It seems desirable that the antenna factor of EMC antennas be revised to the antenna factor with zero reflection presented in this paper for accurate measurements.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1998년도 춘계학술대회 논문집
• /
• pp.35-39
• /
• 1998

Determination of effective EDM parameters is significant to increase productivity. However, With the complexity of EDM phenomena, a universal selection method of EDM parameters has not been established yet. Moreover, No attempt has been tried before to suggest a logical method in determining essential machining parameters for effective electrical discharge machining. Peak current, one of the most significant factors in EDM, is proportional to EDM area. This paper presents a method that can be Z-map modeling from CMM data, and calculate EDM area using Z-map.