• 한국지반공학회논문집
• /
• 제19권4호
• /
• pp.7-14
• /
• 2003

본 연구는 등방성 투수계수를 갖는 점토에 설치된 압밀촉진 케이슨에 관한 선행 연구를 보다 발전시켜서 비등방성 투수계수를 갖는 점토에서의 압밀촉진 케이슨 기초공법의 타당성을 이론적으로 검증하였다. 투수계수의 비등방성을 고려한 2차원 투수 압밀 방정식의 과잉간극수압에 대한 해석해와 시간계수에 따른 평균압밀도 식을 유도하였다. 비등방성 투수계수비가 5, 10, 50인 경우, $\xi$=0.1인 단면에서 평균압밀도 90%에 도달하는 시간은 기존 케이슨에 비해 각각 약 8배, 13배, 47배 단축되었다. 이는 지반의 비등방성 투수계수비가 클수록 압밀촉진 케이슨 기초공법이 압밀에 소요되는 시간을 단축시키는데 효과적임을 의미한다. 또한 본 연구에서는 해석단면의 깊이에 대한 폭의 비 및 비등방성 투수계수비에 따른 전체 해석단면에서의 평균압밀도에 대한 그래프를 제시하였으며, 이를 이용하여 평균압밀침하량을 쉽게 산정할 수 있다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 봄 학술발표회 논문집
• /
• pp.685-692
• /
• 2000

Vertical drain used improvement soft clay is made of not only decreasing construction time but also increasing the ground strength during some decades. As, it is applied to improvement soft clay with vertical drain, it is designed by the result that is caused by oedemeter test ignored anisotropic of the ground related to consolidation conditions. When we are expected consolidation conditions, the most important factors is soil of compaction and water permeability. Above all, anisotropic of the ground permeability show the results which differ between vertical and radial drainage. Recently, We study for radial consolidation coefficient and permeability coefficient that utilized Rowe Cell Consolidation and permeability tester but, it dont use well because of not only a supply lack also difficulty of test. The paper experimented with searching anisotropic of the ground so there are Rowe Cell test, standard consolidation tester and modified standard consolidation test that have pohang's soft clay ground. Therefore, we find anisotropic of the ground and a tester of easy use more than before. We made a comparison test result between the devised tester and Rowe Cell tester, Also, we learned average degree of consolidation for partial penetrating vertical drains. We were found relations as effective stress-void and effective stress-permeability coefficient through those tests.

• 한국지반환경공학회 논문집
• /
• 제4권3호
• /
• pp.5-17
• /
• 2003

수직 및 수평방향 압밀시험을 수행할 수 있도록 제작된 Rowe cell을 사용하여 재성형된 포항 이암풍화토의 수직 및 수평방향의 압밀과 투수특성을 살펴보았고, 그 결과를 Oedometer 시험결과와 비교분석 하였다. 간접투수계수는 9가지의 압밀계수 산정법에 의해 구하여진 압밀계수로부터 산정하였다. 수직배수인 경우 ${\sqrt{t}}$ 법과 hyperbolic 방법에 의한 간접투수계수가 비교적 직접투수계수와 잘 일치하였고, 수평배수의 경우는 전반적으로 모든 방법에서 과대평가되는 경향이 나타났다. 수직 및 수평방향 직접투수계수에 의한 이암풍화토의 투수에 대한 이방성 효과를 검토한 결과 모든 압밀하중에서 평균 약 13정도의 이방성을 보였다.

• 한국지반공학회논문집
• /
• 제16권2호
• /
• pp.61-70
• /
• 2000

When clay foundations of embankments are treated with vertical drain, essentially, the strain occurs to vertical direction but the water flow is radial. The initial horizontal permeability and its variation with the vertical compression are key parameters for the choice of the type of drains, their spacing, and affect to the cost of the project. In this study, CRS consolidation test is performed to investigate the anisotropic characteristics of decomposed mudstone soil and direct permeability test is performed on the same specimens. The results of testing show that Ch is larger than Cv. specially, the Cv - $\sigma$v relationship for a soil sample is viewed from three different curve segments corresponding to overconsolidated, transition and normally consolidated states. The anisotropic ratio, rk(kh/kv) is 2.19. Coefficient of permeability in normally consolidated state is related to its void ratio and permeability parameter n. C can be determined from a linear plot of log[k(1+e)] versus log e. The slope, n, of graphs is the same, whereas the vertical intercept, log C, seems to vary somewhat for anisotropic.

• Geomechanics and Engineering
• /
• 제7권4호
• /
• pp.355-374
• /
• 2014

An analytical solution of the fully coupled system of equations governing the plane strain deformation of a poroelastic medium with anisotropic permeability and compressible fluid and solid constituents is obtained. This solution is used to study the consolidation of a poroelastic clay layer with free permeable surface resting on a rough-rigid permeable or impermeable base. The stresses and the pore pressure are taken as the basic state variables. Displacements are obtained by integrating the coupled constitutive relations. The case of normal surface loading is discussed in detail. The solution is obtained in the Laplace-Fourier domain. Two integrations are required to obtain the solution in the space-time domain which are evaluated numerically for normal strip loading. Consolidation of the clay layer and diffusion of pore pressure is studied for both the bases. It is found that the time settlement is accelerated by the permeability of the base. Initially, the pore pressure is not affected by the permeability of the base, but has a significant effect, as we move towards the bottom of the layer. Also, anisotropy in permeability and compressibilities of constituents of the poroelastic medium have a significant effect on the consolidation of the clay layer.

• Geomechanics and Engineering
• /
• 제21권2호
• /
• pp.103-109
• /
• 2020

The inflow rate is of interest in the design of underground structures such as tunnels and buried pipes below the groundwater table. Soil permeability governing the inflow rate significantly affects the hydro-geological behavior of soils but is difficult to estimate due to its wide range of distribution, nonlinearity and anisotropy. Volume changes induced by stress can cause nonlinear stress-strain behavior, resulting in corresponding permeability changes. In this paper, the nonlinearity and anisotropy of permeability are investigated by conducting Rowe cell tests, and a nonlinear permeability model considering anisotropy was proposed. Model modification and parameter evaluation for field application were also addressed. Significance of nonlinear permeability was illustrated by carrying out numerical analysis of a tunnel. It is highlighted that the effect of nonlinear permeability is significant in soils of which volume change is considerable, and particularly appears in the short-term flow behavior.

• Korea-Australia Rheology Journal
• /
• 제19권1호
• /
• pp.17-25
• /
• 2007

In liquid composite molding (LCM), composites are produced by impregnation of a dry preform with liquid resin. The resin flow through the preform is usually described by Darcy's law and the permeability tensor must be obtained for filling analysis. While the resin flow in the thickness direction can be neglected for thin parts, the resin flow in the transverse direction is important for thicker parts. However, the transverse permeability of the preform has not been investigated frequently. In this study, the transverse permeability was measured experimentally for five different fiber preforms. In order to verify the experimental results, the measured transverse permeability was compared with numerical results. Five different fiber mats were used in this study: glass fiber woven fabric, aramid fiber woven fabric, glass fiber random mat, glass fiber braided preform, and glass/aramid hybrid braided preform. The anisotropic braided preforms were manufactured by using a three dimensional braiding machine. The pressure was measured at the inlet and outlet positions with pressure transducers.

• Fibers and Polymers
• /
• 제4권3호
• /
• pp.135-144
• /
• 2003

Permeability of the preform is one of key factors in design of RTM (Resin Transfer Molding) mold, determination of processing conditions, and modeling of flow in the mold. According to previous studies, permeability measured in the unsaturated fiber mats are higher than that in the saturated fiber mats by about 20% because of the capillary pressure. In this study, permeabilities of several fiber preforms are measured for both saturated and unsaturated flows. A saturated experiment of radial flow has been adopted to measure the permeability of anisotropic fiber preforms with high fiber content, i.e., circular braided preforms. In this method, four pressure transducers are used to measure the pressure distribution. Permeabilities in different directions are determined and the experimental results show a good agreement with the theory. Since permeability is affected by the capillary effect, permeability should be measured in the unsaturated condition for the textile composites to be manufactured under lower pressure as in the Vacuum Assisted Resin Transfer Molding (VARTM).

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2002년도 봄 학술발표회 논문집
• /
• pp.407-414
• /
• 2002

The knowledge of interaction of electromagnetic waves in composite structures is important for designing the shielding structure for antenna such as radome. Recently, radomes are constructed in the form of foam core sandwich structures that have many mechanical advantages such as high strength, long fatigue life, low density and adaptability to the intended function of structure. However, the propagation of electromagnetic waves is affected by high anisotropic permeability and loss tangent of the composite skin. In this study, the analytical model to understand the propagation of electromagnetic waves in the anisotropic composites and foam core sandwich structures with composite skins was proposed. Numerical analyses of unidirectional composites and foam core sandwich structure as a function of incident angle were performed. From the results of analysis, the general tendencies of transmittance of electromagnetic wave through composites and foam core sandwich structure were obtained.

• 한국암반공학회:학술대회논문집
• /
• 한국암반공학회 2000년도 암반공학문제의 수치해석(Numerical Analysis in Rock Engineering Problems)
• /
• pp.129-137
• /
• 2000

본 논문은 통계적 기법에 의한 균열망 해석 프로그램(NAPSAC)을 사용하여 암반의 수리특성을 평가하기 위해 시도되었다. 암반내 존재하는 절리의 방향성을 고려한 투수계수를 산정하기 위해 마북리 시험터널 주위의 시추자료와 막장 자료로부터 얻어진 균열에 대한 정보로부터 대상지역의 등가 투수계수를 추정하였다. 대상지역의 관찰자료(균열망에 대한 자료, 수리지질학적 자료)로부터 통계적 균열망 해석을 위한 입력자료를 결정하여 해석모델의 신뢰성을 확보하였다. 구현된 모델로부터 모델의 크기를증가함에 따라서 이방성 투수계수 및 투수계수의 변화를계산하였다. 해석결과대상지역의 투수성은 균열군의 방향성에 의해 강한 이방성을 보였다.