• Korean Journal of Agricultural Science
• /
• v.37 no.1
• /
• pp.97-104
• /
• 2010

In this study, a laboratory model test on utilization of recycled aggregates and crushed stone as vertical drains to use alternative material of sand in soft ground is performed. The vertical and horizontal coefficient of permeability of the recycled aggregates and crushed stone showed largely 1.2~4.0 times and 3.0~3.3 times greater than sand, respectively. Therefore, it showed enough to be an alternative material to the sand which had been being used as the vertical and horizontal drainage material before. The variations of pore water pressure with time showed constantly regardless of the load in all vertical drainage materials. When water level drops suddenly, the pore water pressure of the recycled aggregate and crushed aggregate is reduced to nearly zero. Therefore, it was applicable to the field because discharge capacity was similarity to that of sand. The settlement in crushed aggregates and recycled aggregate decreases gradually with the load increase. When water level drops suddenly, earth pressure in all drains materials was evaluated the equivalent drainage capacity similarity to sand because it show approaching the nearly zero.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.05a
• /
• pp.321-322
• /
• 2013

Recently, the exhaustion of resource and environmental damage is serious due to the global warming because of the CO₂ exhaust and each type the natural aggregate picking described below. meanwhile, The rest is the actual condition gone to the dumping ground that there is nearly no use which the waste glass can recycle and it is recycled. This research applied the waste glass as the cement substitute material the inorganic binder and coares aggregate substitute material. It utilizes the substitute material of the cement according to it and natural aggregate and tries to develop the environment-friendly artificial stone. The inorganic binder used the blast furnace slag, red mud, and fly ash. The straight type steel fiber, PVA fiber, PA fiber, and cellulosic fiber were used with a kind of fiber. As to the experimental item according to it, the compressive strength is the flexural strength and compressive strength.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2012.11a
• /
• pp.95-96
• /
• 2012

This study makes with the environment-friendly artificial stone which doesn't use the cement and natural aggregate and increases the blast furnace slag that is the eco-friendly material that is the industrial byproduct, fly ash, and availability of the red mud and applies the coares aggregate substitute material as the cleistothecium. The experimental plan according to it indicated the compressive strength and flexural strength which is the most excellent in the mixied ratio 40% of the result degree of closeness magnetism of experimenting with the optimal mix obtained through the preceding stude.

• Journal of Power System Engineering
• /
• v.20 no.5
• /
• pp.86-91
• /
• 2016

This paper is concerned chiefly with the method of porous foam manufacture using basalt stone powder sludge. The hydrogen peroxide($H_2O_2$) of bloating agent has lots of problems to manufacture porous lightweight aggregate due to fast reaction rate with cement or calcium hydroxide($Ca(OH)_2$). The $H_2O_2$ injecting method using nozzle for manufacturing porous lightweight aggregate is proposed, in this study. This method is to inject $H_2O_2$ at the pressure of 10 MPa on upper side of slurry mixing materials such as stone powder sludge and quick-lime(CaO) by injector. The specimen was dried in furnace at $100^{\circ}C$ for 1 hour and cured at ambient temperature for 30 days. We analyzed the characteristics including specific gravity and water absorption. The experiments were found that the porous foam has low specific gravity, high water absorption and uniform distribution of porous more than manufactured foam by general bloating methods.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.6
• /
• pp.63-72
• /
• 2012

The high-flowing concrete requires additionally or excessively more expensive admixture than conventional concrete. So, the concrete has not to be widely used in practical field due to the increase of production price, need of additional facilities, and excessive development of concrete strength in associate with addition of too much cementitious material even though it has more significant advantages than conventional concrete. Thus, this study aims at developing high-flowing concrete with general strength unlike high strength which has been carried out in conventional study. To observe the role of aggregate in the concrete quantitatively and to increase the performance of high-flowing concrete effectively, parametric studies were carried out such as W/C, s/a, fineness modulus of aggregate, contribution degree of particle sizes, and the effect of 13mm aggregate and fine stone powder as a partial replacement of aggregates. And the effect of these factors on performance of the concrete was evaluated by measuring slump-flow and gap of penetration height in U-typed instrument. As a result, it was found that flowability of high-flowing concrete depends upon grading of fine aggregate more significantly than that of coarse aggregate and is enhanced greatly as fineness modulus of fine aggregate decreases and the value of s/a increases. In addition, the application of 13mm aggregate and fine stone powder are expected as a partial replacement of aggregate in order to increase the performance of high-flowing concrete more effectively.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.187-190
• /
• 1999

This study is intended to present the properites of planting concrete using the light-weight aggregate and crushed aggregate. According to the result of experiment, the concrete using orchid stone shows a better performance in voids volume, unit weight, absorbtion, thermal conductivity and pH, which are helpful for planting and heat isolation. Therefore, if planting concrete used with orchid stone are utilized to be the planting base on the building's roof, it will be effective to reduced the cost of construction and heating due to the redution of building's self weight and heat isolation effection.

• Korean Journal of Agricultural Science
• /
• v.24 no.2
• /
• pp.182-193
• /
• 1997

The normal cement concrete is widely used material to build the construction recently, but it has a fault to increase the dead load on account of its unit weight is large compared with strength. Therefore, many engineers are continuously searching for new materials of construction to provide greater performance at lower density. The main purpose of the work described in this paper were to establish the physical and mechanical properties of synthetic lightweight aggregate concrete using perlite on fine aggregate and expanded clay, pumice stone on coarse aggregate. The test results of this study are summarized that the water-cement ratio was shown 47% using expanded clay, 56% using pumice stone on coarse aggregate, unit weight was shown $l,622kgf/m^3$ using expanded clay, $l,596kgf/m^3$ using pumice stone on coarse aggregate, and the absorption ratio was shown same as 17%. The compressive strength was shown more than $228kgf/cm^2$, tensile and bending strength was more than $27kgf/cm^2$, $58kgf/cm^2$ at all types, and rebound number with schmidt hammer was increased with increase of compressive strength. The static modulus was $1.12{\times}10^5kgf/cm^2$ using expanded clay, $1.09{\times}10^5kgf/cm^2$ using pumice stone on coarse aggregate, and stress-strain curves were shown that increased with increase of stress, and the strain on the maximum stress was shown identical with $2.0{\times}10^{-3}$, approximately.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.45 no.1
• /
• pp.74-82
• /
• 2003

In this paper, an experimental program was undertaken to test the analysis on Component and mechanical characteristics for crushed stone of excavated Rocks from Sandstone, Shale, Mudstone, for use as a new source of aggregate. Physical and mechanical properties, required for aggregate materials, of major constituents of rock wastes including Sandstone, Shale, Mudstone, Felsite, Basalt, Marl were measured in the laboratory Test results showed that the Shale, Felsite, Basalt tested in this study might possibly be used for construction aggregates. In case of Sandstone and Mudstone, some physical properties such as rock strength were generally adoptable but the aggregate characteristics were lower than required.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1996.04a
• /
• pp.12-17
• /
• 1996

It is true that aggregate strength is usually not a factor in normal concrete strength because, the aggregate particle is several times stronger than the matrix and the transition zone in concrete. In other words, with most natural aggregates the strength of the aggregate is hardly utilized because the failure is determined by the other two phases. But aggregate characteristics that are significant to concrete technology include porosity, grading or size distribution, moisture absorption, shape and surface texture, crushing strength, elastic modulus, and the type of deleterious substances present. Therefore, in the area of high strength concrete, concrete is much more influenced by properties of aggregate. This experiment is performed to investigate how kinds of aggregare influence on the workability of high strength concrete. In this experiment, four types of aggregate is used, that is crushed river aggregate, crushed stone, recycled aggregate of low strength and recycled aggregate of high strength. In this study, we scrutinize a fundmental study on the workability of high strength concrete according to kinds of aggregate.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2011.05a
• /
• pp.65-67
• /
• 2011

This research analyzed the mechanical properties of high strength concrete produced by limestone aggregate, and summarized the result as follows: Due to the property of unhardened concrete, slump flow value increased more or less according to the increase in LG replacement, but didn't show a big difference while clear tendency of air content couldn't be found. Due to the property of hardened concrete, there appeared an increase in the rate of compressive strength the more LG replacement increased, and the modulus of elasticity also showed a tendency similar to the increase rate of compressive strength.