• KIPS Transactions on Software and Data Engineering
• /
• v.6 no.2
• /
• pp.51-56
• /
• 2017

Given that the utilization of Unmanned Aerial Vehicles (UAVs) is recently increased, a variety of UAV control methods are being applied. In general, it has been used a lot to directly control a UAV via manipulator. However, tangible user interface is required to control UAVs accurately. This paper proposes a method for controlling an UAV based on multiple Myos. The UAV is connected to a ground control station and then controlled by Myos. Intuitive control is possible by controlling the UAV using tangible user interface.

• International Journal of Control, Automation, and Systems
• /
• v.5 no.1
• /
• pp.51-60
• /
• 2007

This paper describes a visual tracking control law of an Unmanned Aerial Vehicle(UAV) for monitoring of structures and maintenance of bridges. It presents a control law based on computer vision for quasi-stationary flights above a planar target. The first part of the UAV's mission is the navigation from an initial position to a final position to define a desired trajectory in an unknown 3D environment. The proposed method uses the homography matrix computed from the visual information and derives, using backstepping techniques, an adaptive nonlinear tracking control law allowing the effective tracking and depth estimation. The depth represents the desired distance separating the camera from the target.

• The Journal of Korea Robotics Society
• /
• v.9 no.3
• /
• pp.154-159
• /
• 2014

The Global Positioning System (GPS) is widely used to aid the navigation of aerial vehicles. However, the GPS cannot be used indoors, so alternative navigation methods are needed to be developed for micro aerial vehicles (MAVs) flying in GPS-denied environments. In this paper, a real-time three-dimensional (3-D) indoor navigation system and closed-loop control of a quad-rotor aerial vehicle equipped with an inertial measurement unit (IMU) and a low-cost light detection and ranging (LIDAR) is presented. In order to estimate the pose of the vehicle equipped with the two-dimensional LIDAR, an octree-based grid map and Monte-Carlo Localization (MCL) are adopted. The navigation results using the MCL are then evaluated by making a comparison with a motion capture system. Finally, the results are used for closed-loop control in order to validate its positioning accuracy during procedures for stable hovering and waypoint-following.

• Fire Science and Engineering
• /
• v.26 no.2
• /
• pp.97-104
• /
• 2012

Forest fires were easy to be larger in Korea. So the utilization of aircrafts, especially helicopters, for forest fire attack would be increased gradually. In the forest fire attack process, the improvement of the helicopter aerial fire attack technique and safety were the chief element for efficient forest fire attack. In this study, we surveyed the recognition of pilots who worked in Forest Aviation Office which was responsible for aerial forest fire attack in Korea. Using these survey results, we suggested more efficient and safer method for aerial fire fighting based on actual experience of air attack at the scene of forest fire burning.

• Proceedings of the KSRS Conference
• /
• 2007.10a
• /
• pp.548-551
• /
• 2007

Among components of digital topographic maps used officially in Korea, only contours have 3D values except buildings and trees that are demanded in landscape planning. This study presented a series of processes for 3Dreconstructing landscape features such as terrain, buildings and standing trees using LiDAR (Light Detection And Ranging) data and aerial digital photo graphs. The 3D reconstructing processes contain 1) building terrain model, 2) delineating outline of landscape features, 3) extracting height values, and 4) shaping and coloring landscape features using aerial photograph and 3-D virtual data base. LiDAR data and aerial photograph was taken in November 2006 for $50km^{2}$ area in Sorak National Park located in eastern part of Korea. The average scanning density of LiDAR pulse was 1.32 points per square meter, and the aerial photograph with RGB bands has $0.35m{\times}0.35m$ spatial resolution. Using reconstructed 3D landscape features, visibility with the growing trees with time and at different viewpoints was analyzed. Visible area from viewpoint could be effectively estimated considering 3D information of landscape features. This process could be applied for landscape planning like building scale with the consideration of surrounding landscape features.

• Journal of Korean Society for Geospatial Information Science
• /
• v.8 no.2 s.16
• /
• pp.89-99
• /
• 2000

The Quality and Accuracy of digital image is important factor for decision of accuracy in digital photogrammetry because all the inside works in digital photogrammetry are based on digital image. But it is still difficult to ensure quality assurance and appication of data because there is no distinct criterion about quality and accuracy of digital image when the works in digital photogrammetry is accomplished. This study presents optimal resolution of aerial photo through error analysis of image coordinate using auto inner orientation in digital photograrnrnetry workstation. In second step, we are valified to optimum resolution of aerial photo image with orientation analysis. Finally, we are established to validity optimal resolution of aerial photo image with production of ortho image and mosaic image using optimal resolution aerial photo image.

• Journal of the Korean Society of Industry Convergence
• /
• v.24 no.6_2
• /
• pp.883-890
• /
• 2021

In this study, joint analysis was conducted on the rock slope by aerial surveying using UAV. Aerial photos were taken using UAV to measure the directionality of the rock slope exposed to the site, and the directionality of the joint was analyzed using the photographed photos. UAV photography was taken under conditions of 90% overlap and an altitude of 50m. The photographing path was measured in the horizontal, vertical, and oblique directions based on the slope, and the joint characteristics were analyzed. Aerial surveying research on the joint directionality analysis of rock slopes is still incomplete, and the method for accurate joint directionality analysis is not presented strategically, so it is difficult to apply it in design. Through the results of this study, we would like to propose an flight photographing technique for the investigation of rock joints. As a result of the study, in the case of the joint investigation of the rock slope using UAV, it was necessary to change conditions such as altitude, aerial photography route, and overlap according to the size of the joint according to the site conditions.

• Journal of Korea Multimedia Society
• /
• v.25 no.2
• /
• pp.237-246
• /
• 2022

Among the technologies of the 4th industrial revolution, drones that have grown rapidly and are being used in various industries can be operated by the pilot directly or can be operated automatically through programming. In order to be controlled by a pilot or to operate automatically, it is essential to predict and analyze the optimal path for the drone to move without obstacles. In this paper, after securing and analyzing the pilot training dataset through the unmanned aerial vehicle piloting training platform designed through prior research, the profile of the dataset that should be preceded to search and derive the optimal route of the unmanned aerial vehicle was designed. The drone pilot training data includes the speed, movement distance, and angle of the drone, and the data set is visualized to unify the properties showing the same pattern into one and preprocess the properties showing the outliers. It is expected that the proposed big data-based profile can be used to predict and analyze the optimal movement path of an unmanned aerial vehicle.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.30 no.4
• /
• pp.57-64
• /
• 2022

A study on propllers for unmaned aerial vehicles is conducted using the open softwares. Since the shape of the propeller is closely related to the thurst characteristics of the propulsion system, adopting an appropriate propeller will significantly reflect stable aerodynamic performances. In this study, propellers for unmanned aerial vehicles were modeled by using OpenVSP and Propel for comparison, the thrust characteristics according to the number of blades and the diameter of the propeller were analyzed. In addition, the tendency of thrust characteristics according to various propeller pitch angles was confirmed. Based on the analysis results of this study, the applicability of the propeller shape to the design of the unmanned aerial vehicle was confirmed. It is shownthat the analysis results of this study can be utilized when modeling the propeller shape in research such as a conceptual design of unmanned aerial vehicle. In this case, it should be noted that OpenVSP does not involve the viscous effect of air.

• The Journal of the Korea Contents Association
• /
• v.8 no.3
• /
• pp.270-278
• /
• 2008

This study : An analysis of position accuracy of topography according to using LiDAR data, aerial photo and digital map for a study area was conducted. The study area was selected in Hadan area, Sahagu, Busan aerial LiDAR data and aerial photo in the scales of 1:20,000, which are high tech surveying ways were used. The final digital orthoimage according to orientation process for each image and image resampling was producted. Using it, a checkpoint was chosen, information about the checkpoints selected was extracted, a coordinate of Horizontal Position through the screen digitizing was also extracted. Both the coordinates of LiDAR data and aerial photo using digital map in the scales of 1:20,000 announced to the public from NGII(National Geographic Information Institute) were gradually compared and analyzed. Based on the digital map, as a result of being both compared and analyzed, it has shown to us that horizontal position of aerial photo is more accurate than that of aerial LiDAR surveying (RMSE-building x:24cm, y:26cm).