• Journal of the Korean Vacuum Society
• /
• v.7 no.4
• /
• pp.368-373
• /
• 1998

As device dimensions approach submicrometer size in ULSI, the demand for interlayer dielectric materials with very low dielectric constant is increased to solve problems of RC delay caused by increase in parasitic resistance and capacitance in multilevel interconnectins. Fluorinated amorphous carbon in one of the promising materials in ULSI for the interlayer dielectric films with low dielectric constant. However, poor thermal stability and adhesion with Si substrates have inhibited its use. Recently, amorphous hydrogenated carbon (a-C:H) film as a buffer layer between the Si substrate and a-C:F has been introduced because it improves the adhesion with Si substrate. In this study, therfore, a-C:F/a-C:H films were deposited on p-type Si(100) by ECRCVD from $C_2F_6, CH_4$and $H_2$gas source and investigated the effect of forward power and composition on the thickness, chemical bonding state, dielectric constant, surface morphology and roughness of a-C:F films as an interlayer dielectric for ULSI. SEM, FT-IR, XPS, C-V meter and AFM were used for determination of each properties. The dielectric constant in the a-C:F/a-C:H films were found to decrease with increasing fluorine content. However, the dielectric constant increased after furnace annealing in $N_2$atomosphere at $400^{\circ}C$ for 1hour due to decreasing of flurorine content. However, the dielectric constant increased after furnace annealing in $N_2$atmosphere at $400^{\circ}C$ for 1hour due to decreasing of fluorine concentration.

• Journal of the Korean Vacuum Society
• /
• v.7 no.4
• /
• pp.403-409
• /
• 1998

In this study, the effects of multi-dipole type of magnets on the characteristics of the inductively coupled plasmas and $SiO_2$ etch properties were investigated. As the magnets, 4 pairs of permanent magnets were used and, to etch $SiO_2, C_2F_6, CHF_3, C_4F_8, H_2$, and their combinations were used. The characteristics of the magnetized inductively coupled plasmas were investigated using a Langmuir probe and an optical emission spectrometer, and $SiO_2$ etch rates and the etch selectivity over photoresist were measured using a stylus profilometer. The use of multi-dipole magnets increased the uniformity of the ion density over the substrate location even though no significant increase of ion density was observed with the magnets. The use of the magnets also increased the electron temperature and radical densities while reducing the plasma potential. When $SiO_2$ was etched using the fluorocarbon gases, the significant increase of $SiO_2$ etch rates and also the increase of etch uniformity over the substrate were obtained using the magnets. In case of gas combinations with hydrogen, $C_4F_8/H_2$ showed the highest etch rates and etch selectivities over photoresist among the gas combinations with hydrogen used in the experiment. By optimizing process parameters at 1000 Watts of inductive power with the magnets, the highest $SiO_2$ etch rate of 8000 $\AA$/min could be obtained for 50% $C_4F_8/50% H_2$.

• Journal of Korean Vacuum Science & Technology
• /
• v.7 no.2
• /
• pp.33-38
• /
• 2003

Fluorinated amorphous carbon thin films (a-C:F) for the use of low dielectric constant intermetallic layer dielectrics are deposited by plasma enhanced chemical vapor deposition with $C_4$F$_{8}$ and Si$_2$H$_{6}$/He gas mixture as precursors. To characterize and improve film properties, we changed various conditions such as deposition temperature, and RF power, and we measured the thickness and refractive indexes and FT-IR spectrum before and after annealing. At low temperatures the film properties were very poor although the growth rate was very high. On the other hand, the growth rate was low at high temperature. The growth rate increased in accordance with the deposition pressure. The dielectric constants of samples were in the range of 1.5∼5.5∼5.

• Journal of Electrochemical Science and Technology
• /
• v.2 no.3
• /
• pp.168-173
• /
• 2011

The availability, low toxicity, and high degree of technological development make silicon the most likely material to be used in solar cells, the cost of solar cells depends entirely on cost of high purity silicon production. The present work was conducted to electrodeposite of silicon from $K_2SiF_6$, an inexpensive raw material prepared from fluorosilicic acid ($H_2SiF_6$) produced in Iraqi Fertilizer plants, and using inexpensive graphite material as cathode electrode. The preparation of potassium fluorosilicate was performed at ($60^{\circ}C$) in a three necks flask provided with a stirrer, while the electro deposition was performed at $750^{\circ}C$ in a three-electrodes configuration with melt containing in graphite pot. High purity potassium fluorosilicate (99.25%) was obtained at temperature ($60^{\circ}C$), molar ratio-KCl/$H_2SiF_6$(1.4) and agitation (600 rpm). Spongy compact deposits were obtained for silicon with purity not less than (99.97%) at cathode potential (-0.8 V vs. Pt), $K_2SiF_6$ concentration (14% mole percent) with grain size (130 ${\mu}m$) and level of impurities (Cu, Fe and Ni) less than (0.02%).

• Journal of the Korean Vacuum Society
• /
• v.6 no.1
• /
• pp.91-96
• /
• 1997

The electrical characteristics and the plasma parameters of planar inductively coupled plasmas (ICP) have been measured. The resistance of the total load including the coil and the plasma varied from 1 to 4 W and the inductance from 1.5 m to 2 mH when the power was changed from 100 to 1000 W and the pressure from 1 to 10 mTorr. The density of electron measured by Langmuir probe was over $10^{11}/\textrm{cm}^3$ and the temperature varied between 3 and 5 eV as the process conditions were changed. Bias modulation was adopted as a new method to improve the selectivity of $SiO_2$on Si in $C_4F_8$ (octafluorocyclobutane) plasma. The selectivity was improved as the duty ratio decreased, but the etch rate of $SiO_2$decreased below 400$\AA$/min. $H_2$addition to $C_4F_8$ plasma showed that the etch selectivity could be higher than 50 and the etch rate of $SiO_2$over 2000$\AA$/min when 60% $H_2$was added.

• Journal of Sensor Science and Technology
• /
• v.13 no.3
• /
• pp.182-187
• /
• 2004

The fluorinated amorphous carbon thin films (a-C:F) were deposited by PECVD(plasma enhanced chemical vapor deposition). The precursors were $C_{4}F_{8}$ which had a similar ratio of target film's carbon to fluorine ratio, and $Si_{2}H_{6}$/He for capturing excessive fluorine ion. We varied deposition condition of temperature and working pressure to survey the effect of each changes. We measured dielectric constant, composition, and etc. At low temperature the film adhesion to substrate was very poor although the growth rate was very high, the growth rate was very low at high temperature. The EDS(energy dispersive spectroscopy) result showed carbon and fluorine peak for films and Si peak for substrate. There was no oxygen peak.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.6
• /
• pp.30-37
• /
• 1989

The PIN type a-SiC:H/a-Si:H heterojunction solar cells were fabricated by using the rf glow discharge decomposition of $SiH_4$ mixed with $CH_4,B_2,H_6\;and\;PH_3.$ The efficiency of the solar cell of the $SnO_2/ITO$ was higher than that of ITO transparent oxide layer by 1.5%. The P layer was prepared with the thickness of $100{\AA}$ and $CH_4/SiH_4$ ration of 5. The I layer has been deposited on the P layer and it is not pure intrinsic but near N type. So $SiH_4$ mixed with $B_2H_6$ of 0.3ppm was used to change this N type nature to intrinsic having the thickness of 5000${\AA}$. And consecutively, the N layer was deposited with t ethickness of $400{\AA}$ using $SiH_4/PH_3$ mixtures. The solar cell demonstrated 0.94V of $V_{oc'}$ 14.6mA/cm of $J_{sc}$ and 58.2% of FF, resulting the efficiency of 8.0%. To minimize loss by the reflection of light, $MgF_2$ layer was coated on the lgass and the efficiency was improved by 0.5%. Therefore, the solar cell indicated overall efficiency of 8.5%.

• Journal of the Korean Ceramic Society
• /
• v.41 no.10 s.269
• /
• pp.749-755
• /
• 2004

Fluosilicic acid ($H_2SiF_6$) is recovered as aqueous solution which absorbs $SiF_4$ produced from the manufacturing of industrial-graded $H_3PO_4$ or HF. Generally, fluosilicate salts prepared by the reaction between $H_2SiF_6$ and metal salts. Addition of fluosilicate salts to cement endows odd properties through unique chemical reaction with the fresh and hardened cement. In this study, two-component fluosilicate salt based chemical admixtures (MZ) of $4\%,\;6\%$, and $8\%$ concentration were prepared by the reaction of $H_2SiF_6$ ($25\pm2\%$) and metal salts. The effect of concentration of MZ at a constant adding ratio on the hydration and watertightness of cement were investigated respectively. In a cement containing MZ, metal fluorides such as $CaF_2$ and soluble silica by hydrolysis were newly formed during hydration. The total porosity of the hardened cement was lower in the presence of U because of packing role of metal fluoride and pozzolanic reaction of soluble $SiO_2$. Consequently, the watertightness of the hardened paste containing MZ was more improved than non-added (plain) due to an odd hydration between cement and MZ.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.454-454
• /
• 2014

Silicon microwire array is one of the promising platforms as a means for developing highly efficient solar cells thanks to the enhanced light trapping efficiency. Among the various fabrication methods of microstructures, deep reactive ion etching (DRIE) process has been extensively used in fabrication of high aspect ratio microwire arrays. In this presentation, we show precisely controlled Si microwire arrays by tuning the DRIE process conditions. A periodic microdisk arrays were patterned on 4-inch Si wafer (p-type, $1{\sim}10{\Omega}cm$) using photolithography. After developing the pattern, 150-nm-thick Al was deposited and lifted-off to leave Al microdisk arrays on the starting Si wafer. Periodic Al microdisk arrays (diameter of $2{\mu}m$ and periodic distance of $2{\mu}m$) were used as an etch mask. A DRIE process (Tegal 200) is used for anisotropic deep silicon etching at room temperature. During the process, $SF_6$ and $C_4F_8$ gases were used for the etching and surface passivation, respectively. The length and shape of microwire arrays were controlled by etching time and $SF_6/C_4F_8$ ratio. By adjusting $SF_6/C_4F_8$ gas ratio, the shape of Si microwire can be controlled, resulting in the formation of tapered or vertical microwires. After DRIE process, the residual polymer and etching damage on the surface of the microwires were removed using piranha solution ($H_2SO_4:H_2O_2=4:1$) followed by thermal oxidation ($900^{\circ}C$, 40 min). The oxide layer formed through the thermal oxidation was etched by diluted hydrofluoric acid (1 wt% HF). The surface morphology of a Si microwire arrays was characterized by field-emission scanning electron microscopy (FE-SEM, Hitachi S-4800). Optical reflection measurements were performed over 300~1100 nm wavelengths using a UV-Vis/NIR spectrophotometer (Cary 5000, Agilent) in which a 60 mm integrating sphere (Labsphere) is equipped to account for total light (diffuse and specular) reflected from the samples. The total reflection by the microwire arrays sample was reduced from 20 % to 10 % of the incident light over the visible region when the length of the microwire was increased from $10{\mu}m$ to $30{\mu}m$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1998.02a
• /
• pp.77-77
• /
• 1998

Present silicon dioxide (SiOz) 떠m as intennetal dielectridIMD) layers will result in high parasitic c capacitance and crosstalk interference in 비gh density devices. Low dielectric materials such as f f1uorina뼈 silicon oxide(SiOF) and f1uoropolymer IMD layers have been tried to s이ve this problem. I In the SiOF ftlm, as fluorine concentration increases the dielectric constant of t뼈 film decreases but i it becomes unstable and wa않r absorptivity increases. The dielectric constant above 3.0 is obtain어 i in these ftlms. Fluoropolymers such as polyte$\sigma$따luoroethylene(PTFE) are known as low dielectric c constant (>2.0) materials. However, their $\alpha$)Or thermal stability and low adhesive fa$\pi$e have h hindered 야1리ru뚱 as IMD ma따"ials. 1 The concept of a plasma processing a찌Jaratus with 비gh density plasma at low pressure has r received much attention for deposition because films made in these plasma reactors have many a advantages such as go여 film quality and gap filling profile. High ion flux with low ion energy in m the high density plasma make the low contamination and go어 $\sigma$'Oss피lked ftlm. Especially the h helicon plasma reactor have attractive features for ftlm deposition 야~au똥 of i앙 high density plasma p production compared with other conventional type plasma soun:es. I In this pa야Jr, we present the results on the low dielectric constant fluorocarbonated-SiOF film d밑JOsited on p-Si(loo) 5 inch silicon substrates with 00% of 0dFTES gas mixture and 20% of Ar g gas in a helicon plasma reactor. High density 띠asma is generated in the conventional helicon p plasma soun:e with Nagoya type ill antenna, 5-15 MHz and 1 kW RF power, 700 Gauss of m magnetic field, and 1.5 mTorr of pressure. The electron density and temperature of the 0dFTES d discharge are measUI벼 by Langmuir probe. The relative density of radicals are measured by optic허 e emission spe따'Oscopy(OES). Chemical bonding structure 3I피 atomic concentration 따'C characterized u using fourier transform infrared(FTIR) s야3띠"Oscopy and X -ray photonelectron spl:’따'Oscopy (XPS). D Dielectric constant is measured using a metal insulator semiconductor (MIS;AVO.4 $\mu$ m thick f fIlmlp-SD s$\sigma$ucture. A chemical stoichiome$\sigma$y of 야Ie fluorocarbina$textsc{k}$영-SiOF film 따~si야영 at room temperature, which t the flow rate of Oz and FTES gas is Isccm and 6sccm, res야~tvely, is form려 야Ie SiouFo.36Co.14. A d dielec$\sigma$ic constant of this fIlm is 2.8, but the s$\alpha$'!Cimen at annealed 5OOt: is obtain려 3.24, and the s stepcoverage in the 0.4 $\mu$ m and 0.5 $\mu$ m pattern 킹'C above 92% and 91% without void, res야~tively. res야~tively.