• Journal of the Korea Institute of Military Science and Technology
• /
• v.15 no.4
• /
• pp.502-506
• /
• 2012

In order to find the structural characteristics of the thin films of group II-VI semiconductor compounds compared with those of powder materials, films were made of 4 powders of ZnS, CdS, CdSe, and CdTe(Aldrich), each with 99.99 % purity. For the ZnS/CdS multi-layers, the ZnS layer was coated over the CdS layer on an $AlO_x$ membrane, which served as a protective layer within a vacuum at the average speed of 1 ${\AA}$/sec. After studying the structures of the group II-VI semiconductor thin films by using X-ray spectroscopy, we found that the ZnS, ZnS/CdS, CdS, and CdSe films were hexagonal and exhibited some degree of preferred orientation. Also, the particles of the thin films of II-VI semiconductor compounds proved to be more homogeneous in size compared to those of the powder materials. These results were further verified through scanning electron microscopy(SEM), EDX analysis, and powder and thin film X-ray diffraction.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.4
• /
• pp.289-293
• /
• 2007

ZnO thn films are grown on five kinds of oxide substrates including $c-Al_2O_3(0001),\;r-Al_2O_3(01-12)$, MgO(100), MgO(111), $NdGaO_3(110)$ by rf magnetron sputtering and effects substrate types on properties of ZnO thin films ate investigated. In order to compare the substrate effects one growth condition is selected and all the films are grown by the same growth condition. Structural and optical properties of the ZnO films ate different depending on the substrates although the films ate not epitaxial but polycrystalline. The ZnO film grown on $NdGaO_3(100)$ substrate shows the best overall properties among the films grown on substrates investigated in this study.

• Journal of Surface Science and Engineering
• /
• v.42 no.3
• /
• pp.122-127
• /
• 2009

Ga/Al doped ZnO (GAZO) thin films were prepared on non-alkali glass substrate by co-sputtering system using two DC cathodes equipped with AZO ($Al_2O_3$:2.0 wt%) target and GZO ($Ga_2O_3$:6.65 wt%) target. This study examined the influence of Al/Ga concentration and substrate temperature on the electrical, structural and optical properties of GAZO films. The lowest resistivity $1.95{\times}10^{-3}{\Omega}cm$ was obtained at room temperature. With increasing substrate temperature, resistivity of GAZO film decreased to a minimum value of $7.47{\times}10^{-4}{\Omega}cm$ at below $300^{\circ}C$. Furthermore, when 0.05% $H_2$ gas was introduced, resistivity of GAZO film decreased to $6.69{\times}10^{-4}{\Omega}cm$. All the films had a preferred orientation along the (002) direction, indicating that the deposited films have hexagonal wurtzite structure formed by the textured growth along the c-axis. The average transmittance of the films was more than 85% in the visible light range.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.143-146
• /
• 2003

Al doped Zinc Oxide(ZnO:Al) films, which is widely used as a transparent conductor in optoelectronic devices such as solar cell, liquid crystal display, plasma display panel, thermal heater, and other sensors, were prepared by using the capacitively coupled DC magnetron sputtering method. The influence of the substrate temperature, working gas pressure and discharge power on the electrical, optical and morphological properties were investigated experimentally. The consideration on the effect of doping amounts of Al on the electrical and optical properties of ZnO thin film were also carried out. ZnO:Al films with the optimum growth conditions showed resistivity of $9.42{\times}10^{-4}\;{\Omeg}-cm$ and transmittance of 90.88% for 840nm in film thickness in the wavelength range of the visible spectrum.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.162-165
• /
• 2006

AZO (ZnO:Al) were fabricated by RF magnetron sputtering In $H_2/Ar(5%\;H_2)$ atmosphere, and structural, electrical and optical properties were investigated. The substrate temperatures were varied at RT, $100^{\circ}C,\;150^{\circ}C$ and$200^{\circ}C$. The resistivity of the films grown in $H_2/Ar(5%\;H_2)$ were reduced from $7.67{\times}10^{-4}{\Omega}\;cm$ to $5.95{\times}10^{-4}{\Omega}\;cm$ comparing that Ar (100%) and the transmittance of the ZnO:Al films in the visible range was 85%.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2009.10a
• /
• pp.177-179
• /
• 2009

In order to investigate the possible application of ZnO films as a transparent conducting oxide (TCO) electrode, ZnO:Al films were prepared by RF magnetron sputtering method. The effects of surface treatment and doping concentration on the structural and electrical properties of ZnO films were mainly studied experimentally. Five-inch PDP cells using either a ZnO:Al or indium tin oxide (ITO) electrode were also fabricated separately under the same manufacturing conditions. The luminous properties of both the transparent conducting oxide electrode were measured and compared with each other. By doping the ZnO target with 2 wt% of Al2O3, the film deposited at a chemical surface treatment resulted in the minimum resistivity of 8.5 _ 10_4 U-cm and a transmittance of 91.7%. And DBD surface treatment resulted in the minimum resistivity of 8.5 _ 10_4 U-cm and a transmittance of 91.7%. Although the luminance and luminous efficiency of the transparent conducting oxide electrode using ZnO:AI are lower than those of the cell with the ITO electrode by about 10%, these values are sufficient enough to be considered for the normal operation of TCO.

• Journal of Surface Science and Engineering
• /
• v.41 no.4
• /
• pp.142-146
• /
• 2008

Trivalent ions(Ga, Al, In) doped ZnO films were deposited by DC magnetron sputtering on non-alkali glass substrate at substrate temperature of $300^{\circ}C$. We used the different three types of high density($95%{\sim}$) ceramic sintered disks(doped with $Ga_2O_3$; 6.65 wt%, $Al_2O_3$; 3.0 wt%, $In_2O_3$; 9.54 wt%). This study examined the effect of different dopants(Ga, Al, In) on the electrical, structural, and optical properties of the films. The lowest resistivity of $5.14{\times}10^{-4}{\Omega}cm$ and the highest optical band gap of 3.74 eV were obtained by Ga doped ZnO(GZO) film. All the films had a preferred orientation along the(002) direction, indicating that the growth orientation has a c-axis perpendicular to the substrate surface. The average transmittance of the films was more than 85% in the visible range.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.5
• /
• pp.307-311
• /
• 2017

ZnO:Al thin films were deposited on glass substrate by RF magnetron sputtering followed by in situ heat treatment in the same chamber. Effects of in situ heat treatment on properties of ZnO:Al thin films were investigated in this study. As heat treatment temperature was increased, crystal quality was improved first and then it was deteriorated, surface roughness was decreased, and sheet resistance was also decreased. The decrease in sheet resistance was caused by increasing carrier concentration due to decreased surface roughness. The decrease in surface roughness resulted in increase of transmittance. Therefore, in situ heat treatment is an effective method for obtaining films with better electrical characteristics.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.8
• /
• pp.716-722
• /
• 2003

ZnO thin films were deposited on Al and Pt electrodes by an RF reactive sputtering system for the fabrication of FBAR (film bulk acoustic wave resonator), and the effect of thermal treatment temperature on their c-axis preferred orientation was investigated. SEM experiments show that columnar structure of ZnO thin films were grown with c-axis normal to electrode material, and XRD experiments show that both ZnO films were grown with (002) plane preferred orientation, but larger diffraction peak was observed with Pt electrode. The peak intensity increased with higher thermal treatment temperature, but c-axis preferred orientation was diminished. The surface roughness of Al thin film was higher than that of Pt, and these affect the surface roughness of ZnO film deposited on the electrode. Though the preferred orientation with respect to Pt(111) plane was improved with higher thermal treatment temperature, this could not improve the c-axis orientation of ZnO film.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.349-349
• /
• 2009

High quality ZnO:Al films were prepared on glass substrates by in-line RF magnetron sputtering and their surface morphologies were modified by wet-etching process in dilute acid solution to improve optical properties for application to silicon thin film solar cells as front electrode. The as-deposited films show a strong preferred orientation in [001] direction under our experimental conditions. A low resistivity below $5{\times}10^{-4}{\Omega}{\cdot}cm$ and high optical transmittance above 80% in a visible range are achieved in the films deposited at optimized conditions. After wet-etching, the surface morphologies of the films are changed dramatically depending on the deposition conditions, especially working pressure. The optical properties such as total/diffuse transmittance, haze and angular resolved distribution of light are varied significantly with the surface morphology feature, whereas the electrical properties are seldom changed. The cell performances of silicon thin film solar cells fabricated on the textured films are also evaluated in detail with comparison of commercial $SnO_2$:F films.