• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.12
• /
• pp.46-53
• /
• 1997

The TMA gas sensors are fabricated with the ZnO-based thin films grown by a RF magnetron sputtering method. The hall effect measurement and AES analysis are carried out to investigate the effects of the sputtering gases and dopants which effect on the electrical resistivity and sensitivity to TMA gas. We measure the cfhanges of the surface carrier concentration, haall electron mobility, electrical resistivity, surface condition, and depth profile of the films. The ZnO-based thin film sensors sputtered in oxygen, or added with dopants showed a high sruface carrier concentration, film sensors sputtered in oxygen and doped with 4.0 wt.% $Al_{2}$O$_{3}$, 1.0 wt.% TiO$_{2}$, and 0.2 wt% v$_{2}$O$_{5}$ showed the highest surface carrier concentration of 5.952 * 10$^{20}$ cm$^{-3}$ , hall electron mobility of 176.7 cm$^{2}$/V.s, lowest electrical resistivity of 6*10$^{-5}$ .ohm.cm and highest sensitivity of 12. These results were measured at a working temperature of 300.deg. C to 8 ppm TMA gas.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.110.1-110.1
• /
• 2012

Recently, advances in ZnO based oxide semiconductor materials have accelerated the development of thin-film transistors (TFTs), which are the building blocks for active matrix flat-panel displays including liquid crystal displays (LCD) and organic light-emitting diodes (OLED). However, the electrical performances of oxide semiconductors are significantly affected by interactions with the ambient atmosphere. Jeong et al. reported that the channel of the IGZO-TFT is very sensitive to water vapor adsorption. Thus, water vapor passivation layers are necessary for long-term current stability in the operation of the oxide-based TFTs. In the present work, $Al_2O_3$ and $TiO_2$ thin films were deposited on poly ether sulfon (PES) and $SnO_x$-based TFTs by electron cyclotron resonance atomic layer deposition (ECR-ALD). And enhancing the WVTR (water vapor transmission rate) characteristics, barrier layer structure was modified to $Al_2O_3/TiO_2$ layered structure. For example, $Al_2O_3$, $TiO_2$ single layer, $Al_2O_3/TiO_2$ double layer and $Al_2O_3/TiO_2/Al_2O_3/TiO_2$ multilayer were studied for enhancement of water vapor barrier properties. After thin film water vapor barrier deposited on PES substrate and $SnO_x$-based TFT, thin film permeation characteristics were three orders of magnitude smaller than that without water vapor barrier layer of PES substrate, stability of $SnO_x$-based TFT devices were significantly improved. Therefore, the results indicate that $Al_2O_3/TiO_2$ water vapor barrier layers are highly proper for use as a passivation layer in $SnO_x$-based TFT devices.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.6
• /
• pp.334-337
• /
• 2017

In this paper, to develop the ceramics with high $d_{33}$ and high $Q_m$ for ultrasonic transducer applications, $0.10Pb(Ni_{1/3}Nb_{2/3})O_3-0.07Pb(Mn_{1/3}Nb_{2/3})O_3-0.83Pb(Zr_{0.5}Ti_{0.5})_{0.83}O_3$ (PNN-PMN-PZT) ceramics were sintered at $940^{\circ}C$ using $CuO-Li_2CO_3-Bi_2O_3$ (CLBO) as a sintering aid by a traditional solid-state technique. The influence of zinc oxide additive on the physical properties of the prepared ceramics were systematically investigated. The R-T (rhombohedral-tetragonal) phase coexistence was found in the ceramics without zinc oxide additive and with increasing amounts of ZnO additive, the specimens showed a tetragonal phase. The formation of a liquid phase between ZnO and $Bi_2O_3$ contributed significantly to the grain growth of specimens. For the 0.1 wt% ZnO ceramics, the optimal physical properties of $d_{33}=370pC/N$, ${\varepsilon}_r=1,344$, $k_p=0.621$, and $Q_m=1,523$ were obtained.

• Journal of Sensor Science and Technology
• /
• v.6 no.4
• /
• pp.265-273
• /
• 1997

The TMA gas sensors are fabricated with the ZnO-based thin films grown by a RF magnetron sputtering method. We investigate the surface carrier concentration, Hall electron mobility, electrical resistivity and sensitivity according to temperature variation and TMA gas concentration. The ZnO-based thin film sensors prepared by sputtering in oxygen showed higher surface carrier concentration, higher Hall mobility, higher sensitivity, and lower electrical resistivity than sensors prepared by sputtering in argon. The doping ZnO-based thin film sensors showed the same electrical properties in comparison with nondoping sensors. In case of sputtering on the oxygen gaseous atmosphere, the ZnO-based thin film sensors doped with 4.0 wt.% $Al_{2}O_{3}$, 1.0 wt.% $TiO_{2}$, and 0.2 wt.% $V_{2}O_{3}$ showed the highest surface carrier concentration of $5.95{\times}10^{20}cm^{-3}$, Hall electron mobility of $177\;cm^{2}/V{\cdot}s$, lowest electrical resistivity of $0.59{\times}10^{-4}{\Omega}{\cdot}cm$ and highest sensitivity of 12.1(working temperature, $300^{\circ}C$, TMA gas, 8 ppm).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.180-180
• /
• 2015

Solution processed Resistive random access memory (ReRAM)은 간단한 공정 과정, 고집적도, 저렴한 가격, 대면적화 플라즈마 데미지 최소화 등의 장점으로 차세대 비휘발성 메모리로 써 많은 관심을 받고 있으며, 주로 high-k 물질인 HfOx, TiOx, ZnO 가 이용 된다. IGZO와 ZTO와 같은 산화물 반도체는 높은 이동도, 대면적화, 넓은 밴드갭으로 인하여 투명한 장점으로 LCDs (Liquid crystal displays)에 이용 가능하며, 최근에는 IGZO와 ZTO에서 Resistive Switching (RS) 특성을 확인한 논문이 보고되면서 IGZO와 ZTO를 ReRAM의 switching medium와 TFT의 active material로써 동시에 활용하는 것에 많은 관심을 받고 있다. 이와 같은 산화물 반도체는 flat panel display 회로에 TFT와 ReRAM의 active layer로써 집적가능 하며 systems-on-panels (SOP)에 적용 가능하다. 하지만 IGZO 보다는 ZTO가 In과 Ga을 포함하지 않기 때문에 저렴하다. 그러므로 IGZO를 대신하는 물질로 ZTO가 각광 받고 있다. 본 실험에서는 ZTO film에 Al을 doping하여 메모리 특성을 평가하였다. 실험 방법으로는 p-type Si에 습식산화를 통하여 SiO2를 300 nm 성장시킨 기판을 사용하였다. 그리고 Electron beam evaporator를 이용하여 Ti를 10 nm, Pt를 100 nm 증착 한다. 용액은 Zn와 Tin의 비율을 1:1로 고정한 후 Al의 비율을 0, 0.1, 0.2의 비율로 용액을 각각 제작하였다. 이 용액을 이용하여 Pt 위에 spin coating방법을 이용하여 1000 rpm 10초, 6000 rpm 30초의 조건으로 AZTO (Al-ZnO-Tin-Oxide) 박막을 증착한 뒤, solvent 및 불순물 제거를 위하여 $250^{\circ}C$의 온도로 30분 동안 열처리를 진행하였다. 이후 Electron beam evaporator를 이용하여 top electrode인 Ti를 100 nm 증착하였다. 제작된 메모리의 전기적 특성은 HP 4156B semiconductor parameter analyzer를 이용하여 측정하였다. 측정 결과, AZTO (0:1:1, 0.1:1:1, 0.2:1:1)를 이용하여 제작한 ReRAM에서 RS특성을 얻었으며 104 s이상의 신뢰성 있는 data retention특성을 확인하였다. 그리고 Al의 비율이 증가할수록 on/off ratio가 증가하고 endurance 특성이 향상되는 것을 확인하였다. 결론적으로 Al을 doping함으로써 ZTO film의 메모리 특성을 향상 시켰으며 AZTO film을 메모리와 트랜지스터의 active layer로써 활용 가능할 것으로 기대된다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.53.2-53.2
• /
• 2011

Dye-sensitized solar cells(DSSCs) have been recognized as an alternative to the conventional p-n junction solar cells because of their simple fabrication process, low production cost, and transparency. A typical DSSC consists of a transparent conductive oxide (TCO) electrode, a dye-sensitized oxide semiconductor nanoparticle layer, liquid redox electrolyte, and a Pt-counter electrode. In dye-sensitized solar cells, charge recombination processes at interfaces between coducting glass, $TiO_2$, dye, and electrolyte play an important role in limiting the photon-to-electron conversion efficiency. A layer of ZTO thin film less than ~200nm in thickness, as a blocking layer, was deposited by DC magnetron sputtering method directly onto the anode electrode to be isolated from the electrolyte in dye-sensitized solar cells(DSCs). This is to prevent the electrons from back-transferring from the electrode to the electrolyte ($I^-/I_3^-$). The presented DSCs were fabricated with working electrode of Ga-doped ZnO glass coated with blocking ZTO layer, dye-attached nanoporous $TiO_2$ layer, gel electrolyte and counter electrode of Pt-deposited GZO glass. The effects of blocking layer were studied with respect to impedance and conversion efficiency of the cells.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.10a
• /
• pp.102.1-102
• /
• 2003

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.5
• /
• pp.101-105
• /
• 1994

The EL lamp have been fabricated by screen printing method. the thickness of BaTiO$_3$ dielectric layer and ZnS:Cu phosphor layer was 20 $\mu$m and 40 $\mu$m, respectively. The threshold voltage of green El lamp was 50 $V_{p-p}$ and the maximum brightness was 13.5 $\mu$ W/cm$^2$ at frequency of 700 Hz and the input voltage of 250 $V_{p-p}$. Also when the Rodamin G6 of 0.02 g was doped, the threshold voltage of white EL lamp was 70 $V_{p-p}$ and the maximum brightness was 34 $\mu$W/cm$^2$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.405-406
• /
• 2013

Ga-doped ZnO (GZO)는 $300^{\circ}C$ 이상의 온도에서는 전기적으로 불안정하기 때문에 CIGS, CdTe, DSC와 같은 태양전지의 높은 공정온도 때문에 사용이 제한적이다. ZTO thin film은 Al2O3, SiO2, TiO2, ZnO tihin film과 비교하여 산소 및 수분에 대하여 투과성이 상대적으로 낮은 것으로 알려져 있다. 따라서 GZO single layer에 비하여 ZTO-GZO multi-layer를 구성하여 TCO를 제작하면, 높은 공정온도에서도 사용 가능하다. 실제 제작된 GZO single layer (300 nm)에서 비저항이 $7.69{\times}10^{-4}{\Omega}{\cdot}cm$에서 $500^{\circ}C$에서 열처리 후 $7.76{\times}10^{-2}{\Omega}{\cdot}cm$으로 급격하게 상승한다. ZTO single layer (420 nm)는 as-grown에서는 측정 불가했지만, $400^{\circ}C$에서 열처리 후 $3.52{\times}10^{-1}{\Omega}{\cdot}cm$ $500^{\circ}C$에서 열처리 후 $4.10{\times}10^{-1}{\Omega}{\cdot}cm$으로 열처리에 따른 큰 변화가 없다. 또한 ZTO-GZO multi-layer (720 nm)의 경우 비저항이 $2.11{\times}10^{-3}{\Omega}{\cdot}cm$에서 $500^{\circ}C$에서 열처리 후 $3.67{\times}10^{-3}{\Omega}{\cdot}cm$으로 GZO에 비하여 상대적으로 변화폭이 작다. 또한 ZTO의 두께에 따른 영향을 확인하기 위하여 ZTO를 2 scan, 4 scan, 6 scan 공정 진행 및 $500^{\circ}C$에서 열처리 후 ZTO, ZTO-GZO thin film의 비저항을 측정하였다. ZTO의 경우 $3.34{\times}10^{-1}{\Omega}{\cdot}cm$ (2 scan), $3.62{\times}10^{-1}{\Omega}{\cdot}cm$ (4 scan), $4.1{\times}10^{-1}{\Omega}{\cdot}cm$ (6 scan)으로 큰 차이가 없으며, ZTO-GZO에서도 $3.73{\times}10^{-3}{\Omega}{\cdot}cm$ (2 scan), $3.42{\times}10^{-3}{\Omega}{\cdot}cm$ (4 scan), $3.67{\times}10^{-3}{\Omega}{\cdot}cm$ (6 scan)으로 큰 차이가 없음을 확인하였다. 염료감응 태양전지에 적용하여 기존에 사용되는 FTO대신에 ZTO-GZO를 사용하며, 가격적 측면, 성능적 측면에서 개선 가능할 것으로 생각된다.