• 한국정밀공학회지
• /
• 제16권4호통권97호
• /
• pp.110-115
• /
• 1999

The surface gloss of an injection molded part is one of the most significant point for evaluating the quality of products appearance. The effects of process condition on the gloss of ABS(Acrylonitrile-Butadiene-Styrene) molded part were investigated in this work. The measurements of gloss and morphology on the surface of molded part were carried out with different melt temperature, mold temperature, mold surface roughness, injection pressure and holding pressure. Gloss had a maximum value with melt temperature in the range of 210 to 220 ${^\circ}C$ and with mold temperature 40 to 50${^\circ}C$ and with injection pressure 80~90 MPa, respectively. Melt temperature was shown to have the largest effect on gloss in our work. Gloss was not improved in the region of melt temperature 240${^\circ}C$ above and of mold temperature 60${^\circ}C$ above. It was concluded that the variation of gloss was mainly caused by rubber particles migration under shear stress not by their aggregation or necklace.

• 한국산업융합학회 논문집
• /
• 제17권4호
• /
• pp.203-210
• /
• 2014

In this study, we present a method for correcting unbalanced sitting posture alignment to its optimal position, by designing a chair equipped with pressure sensor. With increasement in sedentary work, such as office work or study, people are now spending more time in chair. To accommodate sedentary life styles, many chairs are being designed for a comfortable sitting condition. However, without awareness and efforts for correct sitting posture, it may not be possible to achieve such condition. When the weight is not distributed evenly while sitting, it may cause various diseases such as scoliosis and a herniated disc. Being inspired by such facts, we have progressed basic researches to maintain the correct sitting posture. To demonstrate the proof-of-concept validation, we installed a series of sensors to a chair and then measured the changes in pressure distribution in various postures. The results show that this approach can be potentially helpful for understanding how fundamental problems due to unbalanced sitting posture can be corrected and maintained properly.

• 대한한방소아과학회지
• /
• 제21권1호
• /
• pp.173-187
• /
• 2007

Objectives : In order to verify the cardiovascular hemodynamic function of Kammaegdaejo-tang, the experiment was performed in the rats. Methods : Twelve hearts removed from male Sparague-Dawley rats weighing between 250g and 300g were perfused by the Langendorff technique with modified 37 Krebs-Henseleit's buffer solution at a constant perfusion pressure. They were randomly assigned to one of two groups, supplied with either normal saline or Kammaegdaejotang administration. Heart rate, left ventricular pressure, +dp/dt maximum, -dp/dt maximum, and -dp/dt/ +dp/dt ratio were evaluated at baseline after the administration of either normal saline or Kammaegdaejotang. Results : Kammaegdaejotang made the heart rate increasing significantly (p<0.05). Kammaegdaejotang did not effectively work on left ventricular pressure of the isolated heart(p=0.11, no significance). The significant effects of Kammaegdaejotang were observed on +dp/dt max and -dp/dt max(p<0.05). Kammaegdaejotang did not effectively work on -dp/dt/ +dp/dt ratio(p=0.24, no significance).

• Nuclear Engineering and Technology
• /
• 제54권3호
• /
• pp.834-841
• /
• 2022

System thermal-hydraulic (STH) code is adopted for nuclear safety analysis. The critical flow model (CFM) is significant for the accuracy of STH simulation. To overcome the defects of current CFMs (low precision or long calculation time), a CFM based on a genetic neural network (GNN) has been developed in this work. To build a powerful model, besides the critical mass flux, the critical pressure and critical quality were also considered in this model, which was seldom considered before. Comparing with the traditional homogeneous equilibrium model (HEM) and the Moody model, the GNN model can predict the critical mass flux with a higher accuracy (approximately 80% of results are within the ±20% error limit); comparing with the Leung model and the Shannak model for critical pressure prediction, the GNN model achieved the best results (more than 80% prediction results within the ±20% error limit). For the critical quality, similar precision is achieved. The GNN-based CFM in this work is meaningful for the STH code CFM development.

• 운동영양학회지
• /
• 제23권1호
• /
• pp.55-62
• /
• 2019

[Purpose] The effect of acute nitrate supplementation on muscle fatigue is largely unknown. This study aimed to evaluate the effect of acute nitrate supplementation on muscle fatigue. [Methods] Thirty-five recreationally active subjects consumed 140 ml of beetroot (BR) juice (nitrate: 8 mmol·d^-1) or placebo (PL) 12 and 2.5 hours before two exercise sessions. Peak torque was measured during 50 repetitions, at maximal effort, and during concentric knee extensions at 90°·s^-1. Blood pressure (BP) was recorded pre- and post-exercise. [Results] Peak torque, maximum work, rate of fatigue, and rate of work fatigue were similar between the BR and PL conditions. Post-exercise diastolic BP (BR: 67.2 ± 9.8 vs. PL: 64.5 ± 7.9 mmHg, p < 0.05) and mean arterial pressure (BR: 91.6 ± 9.3 vs. PL: 88.8 ± 8.2 mmHg, p < 0.05) were higher with BR supplementation. [Conclusion] These findings suggest that the acute intake of BR juice had no effect on knee extensor muscle strength or fatigue but increased BP in a healthy recreationally active population.

• 설비공학논문집
• /
• 제16권5호
• /
• pp.414-420
• /
• 2004

The heat transfer and pressure drop characteristics associated with the gas cooling of the supercritical carbon dioxide in a horizontal tube have been investigated experimentally. This problem is of particular interest in the design of a gas cooler of cooling systems using $CO_2$refrigerant. The test section is consisted of 6 series of 455 mm in length, 4.15 mm ID copper tube, respectively. The effects of the inlet temperature, pressure and mass flow rate on the heat transfer and pressure drop of $CO_2$in a horizontal tube is studied in detail. The heat transfer coefficient of $CO_2$is varied by temperature, inlet pressure, and mass flow rate of $CO_2$. This has maximum value at near the pseudocritical temperature. The pressure drop is changed by inlet pressure and mass flow rate of $CO_2$. The results have been compared with those of previous work. The heat transfer correlation at the supercritical gas cooling process is also suggested.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년도 제30회 춘계학술대회논문집
• /
• pp.103-106
• /
• 2008

본 연구에서는 발사체 비행 중 가속도의 변화로 발생하는 엔진 입구압력의 변화를 고려하여 엔진의 구성품에 미치는 영향을 고찰하였고 그에 따른 엔진 성능 변화를 예측하였다. 엔진의 입구압은 탱크 내의 추진제 수두와 가압 압력 및 압력 손실 등으로 정의되며 이에 따라 발사체가 비행하면서 추진제 소모와 가속도 변화에 의해 입구압력이 변하게 된다. 입구압이 변할 때 펌프 토출압이 변하고 그에 따른 유량 변화로 가스발생기의 압렵변화가 발생하며, 이는 터빈의 출력변화로 이어져 다시 펌프의 토출압 변화로 나타남을 알 수 있었고, 이는 궁극적으로 주연소실의 연소압 변화를 이끌면서 엔진의 성능이 변화함을 알 수 있었다.

• 대한기계학회논문집B
• /
• 제24권4호
• /
• pp.555-560
• /
• 2000

This paper describes the macroscopic behavior and atomization characteristics of the high-pressure gasoline injector in direct-injection gasoline engine. The global spray behavior of fuel injector was visualized by shadowgraph technique. The atomization characteristics of gasoline spray such as mean diameter and mean velocity of droplet were measured by the phase Doppler particle analyzer system. In order to obtain the influence of fuel injection pressure, the macroscopic visualization and experiment of particle measurement on the fuel spray were investigated at 3,5 and 7 MPa of injection pressure under different surrounding pressure in the spray chamber. The results of this work show that the fuel injection pressure of gasoline injector in GDl engine has influence upon the mean droplet diameter, mean velocity of spray droplet, the spray tip penetration, and spray width under the elevated ambient pressure.

• 한국자동차공학회논문집
• /
• 제15권4호
• /
• pp.132-138
• /
• 2007

Experimental results of pulsating pressure behavior inside a chamber have been confirmed by computational work. Inside-cylinder pressure shows unstable condition at low rpm. This is caused by plate-type suction valve. It has effect up to inlet of the chamber. But trembling phenomenon is reduced as the pressure is enlarged by increasing the rpm. Result comparison between experimental and numerical analysis shows pulsation reduction is affected by the chamber. We can confirm that compressible effect of the working flow is shown at chamber inlet by increasing rpm. On the other side, this effect is declined at chamber outlet by increasing rpm. It means outlet pressure is going on balance with atmosphere pressure. Buffer plate-type chamber has efficiency of pulsation flow reduction.

• 한국기계가공학회지
• /
• 제16권6호
• /
• pp.81-86
• /
• 2017

The high-pressure resin transfer molding (HP-RTM) process has a very effective for the mass production of carbon fiber reinforced plastic (CFRP) for light weight in the automotive industry. In developing robust equipment, new process and fast cure matrix systems reduces significantly the cycle time less than 5 minutes in recent years. This paper describes the cavity pressure, temperature and molding characteristics of the HP-RTM process. The HP-RTM mold was equipped with two cavity pressure sensors and three temperature sensors. The cavity pressure characteristics of the HP-RTM injection, pressurization, and curing processes were studied. This experiment was conducted with selected process parameters such as mold cap size, maximum press force, and injection volume. Consequently, this monitoring method provides correlations between the selected process parameters and final forming characteristics in this work.