• Journal of Welding and Joining
• /
• v.30 no.3
• /
• pp.26-31
• /
• 2012

Three-dimensional integrated circuit (3D IC) technology has become increasingly important due to the demand for high system performance and functionality. We have evaluated the effect of Buffered oxide etch (BOE) on the interfacial bonding strength of Cu-Cu pattern direct bonding. X-ray photoelectron spectroscopy (XPS) analysis of Cu surface revealed that Cu surface oxide layer was partially removed by BOE 2min. Two 8-inch Cu pattern wafers were bonded at $400^{\circ}C$ via the thermo-compression method. The interfacial adhesion energy of Cu-Cu bonding was quantitatively measured by the four-point bending method. After BOE 2min wet etching, the measured interfacial adhesion energies of pattern density for 0.06, 0.09, and 0.23 were $4.52J/m^2$, $5.06J/m^2$ and $3.42J/m^2$, respectively, which were lower than $5J/m^2$. Therefore, the effective removal of Cu surface oxide is critical to have reliable bonding quality of Cu pattern direct bonds.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.406-406
• /
• 2010

일반적으로, 나노스케일의 MOS 소자에서는 게이트 절연체 두께가 감소함에 따라 tunneling effect의 증가로 인해 PID (plasma induced damage)로 인한 소자 특성 저하 현상을 감소하는 추세로 알려져 있다. 하지만 요즘 많이 사용되고 있는 high-k 게이트 절연체의 경우에는 오히려 더 많은 charge들이 trapping 되면서 PID가 오히려 더 심각해지는 현상이 나타나고 있다. 이러한 high-k 게이트 식각 시 현재는 주로 Hf-based wet etch나 dry etch가 사용되고 있지만 gate edge 영역에서 high-k 게이트 절연체의 undercut 현상이나 PID에 의한 소자특성 저하가 보고되고 있다. 본 연구에서는 이에 차세대 MOS 소자의 gate stack 구조중 issue화 되고 있는 metal gate 층과 gate dielectric 층의 식각공정에 각각 중성빔 식각과 중성빔 원자층 식각을 적용하여 전기적 손상 없이 원자레벨의 정확한 식각 조절을 해줄 수 있는 새로운 two step 식각 공정에 대한 연구를 진행하였다. 먼저 TiN metal gate 층의 식각을 위해 HBr과 $Cl_2$ 혼합가스를 사용한 중성빔 식각기술을 적용하여 100 eV 이하의 에너지 조건에서 하부층인 $HfO_2$와 거의 무한대의 식각 선택비를 얻었다. 하지만 100 eV 조건에서는 낮은 에너지에 의한 빔 스케터링으로 실제 패턴 식각시 etch foot이 발생되는 현상이 관찰되었으며, 이를 해결하기 위하여 먼저 높은 에너지로 식각을 진행하고 $HfO_2$와의 계면 근처에서 100 eV로 식각을 해주는 two step 방법을 사용하였다. 그 결과 anistropic 하고 하부층에 etch stop된 식각 형상을 관찰할 수 있었다. 다음으로 3.5nm의 매우 얇은 $HfO_2$ gate dielectric 층의 정확한 식각 깊이 조절을 위해 $BCl_3$와 Ar 가스를 이용한 중성빔 원자층 식각기술을 적용하여 $1.2\;{\AA}$/cycle의 단일막 식각 조건을 확립하고 약 30 cycle 공정시 3.5nm 두께의 $HfO_2$ 층이 완벽히 제거됨을 관찰할 수 있었다. 뿐만 아니라, vertical 한 식각 형상 및 향상된 표면 roughness를 transmission electron microscope(TEM)과 atomic force microscope (AFM)으로 관찰할 수 있었다. 이러한 중성빔 식각과 중성빔 원자층 식각기술이 결합된 새로운 gate recess 공정을 실제 MOSFET 소자에 적용하여 기존 식각 방법으로 제작된 소자 결과를 비교해 본 결과 gate leakage current가 약 one order 정도 개선되었음을 확인할 수 있었다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.351-354
• /
• 2004

This work presents a simple and cost-effective approach for maskless fabrication of positive-tone silicon master for the replica molding of hyperfine elastomeric channel. Positive-tone silicon masters were fabricated by a maskless fabrication technique using the combination of nanoscratch by Nanoindenter ⓡ XP and XOH wet etching. Grooves were machined on a silicon surface coated with native oxide by ductile-regime nanoscratch, and they were etched in a 20 wt％ KOH solution. After the KOH etching process, positive-tone structures resulted because of the etch-mask effect of the amorphous oxide layer generated by nanoscratch. The size and shape of the positive-tone structures were controlled by varying the etching time (5, 15, 18, 20, 25, 30 min) and the normal loads (1, 5 mN) during nanoscratch. Moreover, the effects of the Berkovich tip alignment (0, 45$^{\circ}$) on the deformation behavior and etching characteristic of silicon material were investigated.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.5 no.4
• /
• pp.408-413
• /
• 1995

We investigated the effect of mechanical backside damage upon minority carrier recombination lifetime measurement in Czochralski silicon substrate by laser excitation/microwave reflection photoconductance decay method. The intensity of mechanical damage was evaluated by X-ray double crystal rocking curve, X-ray section topography and wet oxidation/preferential etch methods. The data indicate that the higher the mechanical damage intensity, the lower the minority carrier lifetime, and the threshold full width at half maximum value which affect minority carrier lifetime measurement is about 13 secs.

• Journal of the Korean Ceramic Society
• /
• v.31 no.6
• /
• pp.601-608
• /
• 1994

Aluminum oxide thin films were deposited on p-type(100) silicon substrates by electron cyclotron resonance plasma enhanced CVD(ECR-PECVD) using TMA[Al(CH3)3] and oxygen as reactant gases at 16$0^{\circ}C$ or lower temperatures. The aluminum oxide films deposited by ECR-PECVD have the amorphous structure with the refractive index of 1.62~1.64 and the O/Al ratio of 1.6~1.7. Oxygen flow rate necessary for the stable deposition of the aluminum oxide films increases as the deposition temperature increases. It was found from the OES analysis that the ECR plasma had les cooling effect by introducing the TMA reactant gas in comparison with the RF plasma. The properties of aluminum oxide films prepared by ECR-PECVD were compared with those prepared by RF-PECVD. The ECR-PECVD aluminum oxide films have the higher refractive indices, the lower contents of impurities (H and C) and the stronger wet etch resistance than those deposited by RF-PECVD.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.6
• /
• pp.668-675
• /
• 2013

We investigate the effect of the ageing time and etching time on the etching rate of SiGe mixed etching solution, namely 1 vp HF (6%), 2 vp $H_2O_2$ (30%) and 3 vp $CH_3COOH$ (99.8%). For this etching solution, we found that the etch rate of SiGe layer is saturated after the ageing time of 72 hours, and the selectivity of $Si_{0.8}Ge_{0.2}$ layer and Si layer is 20:1 at ageing time of 72 hours. The collapse was appeared at the etching time of 9min with etching solution of after saturation ageing time.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.2
• /
• pp.60-69
• /
• 1998

Polysilicon surface mdoification tecnique is developed to reduce the sticking of microstructures fabricated by micromachining. Modified anti-sticking grain holes are simply formed by two-step dry eth without additional photolithography nor deposition of thin films. Both process-induced sticking and in-use sticking are successfully reduced more than two times by adopting grain holed polysilicon substrate. A sticking model for cantilever beam is derived. This model includes bending moment stems from stress gradient along the thickness directionof structural polysilicon. Because the surface tension of rinse liquid and the surface energy of the solids to be stuk tend to decrease in recently developed anti-sticking techniques, the effect of stress gradient will play an important role to analyze the sticking phenomena. Effect of the temperature during post-release rinse and dry is modelled and verified experimentally. Based on developed anti-sticking polysilicon structure and the sticking model, sticking of microstructure, fabricated by simple wet process including sacrificial layer etch and rinse with deionized water without special equimpment for post-release rinse and dry was alleviated more than 3.5 times.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.288-290
• /
• 1997

Pulsed laser ablation has been used to fabricate superconducting $YBa_2Cu_3O_{7-x}$(YBCO) thin films on MgO substrates. The epitaxial YBCO thin films were grown at $750^{\circ}C$ and oxygen partial pressure of 200 mTorr. The electrical property and the characteristics of the YBCO thin films have been studied by R-T measurement. scanning electron microscopy (SEM) and X-ray diffraction (XRD). A microstrip line resonator has been fabricated using YBCO superconducting thin films by photolithography and wet-etch process. The resonator has linear microstrip line separated by a gap of 0.278 mm. We observed a fundamental resonance peak at the frequency of 10.007 GHz.

• Proceedings of the KACD Conference
• /
• 2001.11a
• /
• pp.560.1-560
• /
• 2001

To evaluate the micro-shear bond strength of current adhesive systems to cervical and mid-coronal enamel. Materials and Two commercially available resin adhesives were investigated; a self-etching primer system(Clearfil SE Bond, Kyraray) and a one-bottle adhesive system(Single Bond, 3M) intended for use with the total-etch wet-bonding technique were employed. Two regions of enamel, cervical and mid-coronal regions, were chosen from the buccal surface of extracted molars and were then bonded with each adhesive system and submitted to the micro-shear bond test.(중략)

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.9
• /
• pp.1386-1392
• /
• 1990

Characteristics of the direct thermal nitrided films by RF induction heating has been studied. The nitrided films on Si were prepared at 1000-1200\ulcorner in ammonia gas ambient. The nitrided films were analyzed by ellipsometry an Auger electron spectroscopy. I-V and C-V characteristics of MIS capacitors fabricated using nitrided film were investicated. The nitrided films were grown up mostly within initial thirty minutes and no significant growth was observed thereafter. Etch rates of films were about 1\ulcornermin in diluted HF (HF:H2O= 1:50). The nitrided films were resistant to dry and wet oxidations at temperatures below 1000\ulcorner and 900\ulcorner, respectively.