• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.2
• /
• pp.158-161
• /
• 2006

The purpose of this research is to establish the crosstalk characteristic of mm-wave Coplanar structure. The components in mm-wave CPW are classified to transmission devices, EM devices, and quasi - TEM devices. After design of these devices, we analyzed these CPW s electromagnetically using FDTD method, and suggested the corsstalk characteristic of mm-wave CPW. In oder to realize a CPW module up to 30 GHz-100 GHz band, we research on a technology of 3-dimensional mm-wave CPW, and GaAs substrate with ohmic lossy layer. As a result this research, we suggested the optimum crosstalk characteristic of mm-wave CPW, and improved the crosstalk quality of mm-wave CPW.

• Journal of Advanced Navigation Technology
• /
• v.15 no.5
• /
• pp.774-780
• /
• 2011

This paper presents a Bagley polygon and Gysel divider using open-stub loaded transmission line. The structure of slow-wave characteristic consists of small transmission line and shunt capacitive open stub that have reduced characteristic impedance and phase velocity, so we can implement the small circuit size. To validate the slow-wave characteristics, we are implemented the slow-wave characteristic of Bagley polygon and Gysel divider at center frequency 2.1 GHz. Its characteristics are same, but the circuit size is reduced above 15 % respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.5
• /
• pp.694-700
• /
• 1999

In this paper, we studied the design of power divider using the slow-wave effect of Photonic Bandgap structure, which is etched on the ground plane. The proposed PBG structure can provides the changing of the characteristic impedance of the transmission line and the group delay velocity characteristic. Therefore we can make wider width than the width of conventional transmission line and decrease the length of transmission line. We presented the application for power divider using the characteristic impedance and electrical length extracted from scattering parameter. As adding proposed defect units, the effect of defect is studied. The experimental results show good agreements with the simulated results.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.11
• /
• pp.3075-3083
• /
• 1994

The applications of the electrical transmission line theory to the pressure propagation characteristics in the volume loaded fluid transmission line with step and impulse input wave is demonstrated in this paper. The method is based on the premise that the time response is the inverse Fourier transform of frequency spectrum of the wave which spectrum is a product of frequency spectrum of input pressure wave and system transfer function. The frequency response and transient response of step and impulse input wave in the volume loaded fluid transmission line is analysed by the Laplace transform and inverse Laplace transform with FFT numerical algorithm. The numerical solution of the distributed friction model is compared with the average friction model and the infinite product model. And the result is showed that FFT method may have major advantages for the simulation of fluid circuitary.

• Journal of Fashion Business
• /
• v.12 no.6
• /
• pp.11-22
• /
• 2008

The goal of this study is to provide beauticians with the fundamental material to use effectively heat permanent wave in beauty industry as well as their customer's satisfaction. It carried out an experiment with damaged hair of a woman in her late twenties to investigate the change of physical and morphological characteristics by its water content when performing heat permanent wave. After spreading 0g, 1g, 2g, 3g, and 4g of water on damaged hair respectively, heat permanent wave was treated and the change of hair was observed. The change of physical characteristic was compared through permanent wave form of hair, tensile strength and elongation. The change of morphological characteristic was observed through Scanning Electron Microscope(SEM) and Transmission Electron Microscope(TEM). The result of experiment on the physical specificity revealed that permanent wave form was the most ideal when the water content was 2g, also 3g. Though the materials with much moisture content formed the results were not satisfied. The material with 0g of water content didn't make the wave. In terms of tensile strength and elongation, tensile strength was generally reduced as per the damaged degree of hair. On the contrary, elongation was increased. It observed the changes of morphological characteristic that the damage on hair cuticle was deepen, as its moisture content was decreased, and cuticle's surface was worn away. The observation of fine structure on hair section by transmission electronic microscope also certainly showed the result that damaged hair having experience with chemical treatment had got much damaged to hair cuticle as well as hair cortex. Generally chemical treatment makes hair damaged. Under consideration of this aspect, the ultimate goal of this thesis is to minimize the damage of hair caused by chemical treatment and get the satisfaction on the hair style. According to the result of experiment, the damaged hair whose moisture content was 3g showed the best permanent wave form.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.36 no.5
• /
• pp.528-534
• /
• 2003

The 2-D hydraulic experimental results for the submerged rubble-mound structure, we have been concerned with the slability/function characteristics of the structures by the effects of wave force, scour/deposition at the toe and the wave transmission ratio at the lee-side sea. So, to investigate the variation characteristics of the wave transmission ratio which depended on a geometrical structure of the submerged breakwater profiles, the critical conditions for the depth of submergence and crest width were obviously presented. In summary, the results lead us to the conclusion that the wave control capabilities of submerged breakwaters by the variation of the submergence depth is higher than about 4 times the degree at the efficiency than the that of crest width. The destruction of the covering block at the crest generated at the region which was located between the maximum and minimum damage curve, and it's maximum damage/failure station from the toe of the structure was $0.2\;L_s.$ As the wave transmission coefficient and the slope of the structure increase, the damage/failure ratio and the maximum scour depth at the toe was extended, respectively. When the maximum scour depth happened, the destruction of the covering block which was located at the toe generated at the front of the submerged rubble-mound breakwater. Finally, it was found from the results that the optimization of the structure may be obtained by the efficient decision of the submergence depth and crest width in the permissible range of the wave transmission ratio.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2003.10a
• /
• pp.213-219
• /
• 2003

As the 2-D hydraulic experimental results for the submerged rubble-mound structure, we have concerned with their stability/function characteristics of structures by the effects of wave force, scour/deposition at the toe and wave transmission ratio at the lee-side sea. And as to investigate the variation characteristics of wave transmission ratio which depended to a geometrical structure of the submerged breakwater profiles, the critical conditions for the depth of submergence and crest width obviously presented. In summary, there results lead us to the conclusions that the wave control capabilities of submerged breakwaters by the variation of the submergence depth is high about 4 time degrees at the efficiency than the that of crest width. The destruction of covering block at the crest generated at the region which located between maximum damage curve, it maximum damage/failure station from the toe of the structure were 0.2L. As the wave transmission coefficient and the slope of the structure increase, the damage/failure ratio and the maximum scour depth at the toe was extended, respectively. When maximum scour depth happened. The destruction of covering block which located at the toe generated at the front slope destruction. Finally, it was found from the results that the optimization of structure may be obtained by the efficiently decision of the submergence depth and crest width in the permissible range of wave transmission ratio.

• Korean Journal of Optics and Photonics
• /
• v.14 no.4
• /
• pp.434-442
• /
• 2003

Taking advantage of the probability function, we have analyzed the localization phenomenon of the solution of a propagating function under the condition that the propagation constants are randomly distributed. For example, we have investigated the localization phenomenon of the voltage wave for a transmission line in which the characteristic impedance is randomly distributed. We have confirmed that the localized solution is in existence on the random lossless transmission line. Even in the case that the voltage wave is impulsively excited by the current source, the voltage wave is localized. Because the light wave is seriously affected at the localized position in the lossy transmission line, we have determined that the light wave localization phenomena are generated by multi-reflection.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.2
• /
• pp.151-156
• /
• 2021

Leakage and Bragg condition of optical waveguide with asymmetric rectangular grating profile are evaluated in detail by using novel and rigorous modal transmission-line theory (MTLT) based on eigenvalue problem. The optical waveguide composed by asymmetric rectangular grating occur leaky-wave stop-bands at Bragg conditions, and anomalies based on Rayleigh-Wood condition near Bragg conditions. Furthermore, DFB properties of the guiding structure at Bragg conditions are analyzed by applying longitudinal equivalent transmission-line with characteristic impedance of periodic grating. The numerical results show that filtering characteristics that maximize the reflected power of DFB waveguide are activated near Bragg conditions, in which leaky-wave stop-bands occur.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.3
• /
• pp.267-273
• /
• 2008

The circular cylinder pipes are used in the many industrial areas. In this paper, the acoustic wave propagation in the pipe containing a gas is researched. First of all, the theory for the coupled acoustic wave propagation in a pipe is investigated. Acoustic wave propagation in pipe can not be occurred independently between the wave of the fluid and the shell. It requires complicated analysis. However, as a special case, the coupled wave in a high density pipe containing a light density medium is corresponded closely to the uncoupled in-vacuo shell waves and to the rigid-walled duct fluid waves. The coincidence frequencies of acoustic and shell modes contribute to the predominant energy transmission. The coincidence frequency means the frequency corresponding to the coincidence of the wavenumber in both acoustic and shell. In this paper, it is assumed that the internal medium is much lighter than the pipe shell. After the uncoupled acoustic wave in the internal medium and uncoupled shell wave are considered, the coincidence frequencies are found. The analysis is successfully confirmed by the verification of the experiment using the real long steel pipe. This work verifies that the coupled wave characteristic of the shell and the fluid is occurred as predominant energy transmission at the coincidence frequencies.