• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.33 no.6
• /
• pp.514-519
• /
• 2000

In order to develop the method for the calculation of flow resistance acting on cage net, the relation between the velocity reduction factor and $S_n/S$, the ratio of total area of netting projected to the perpendicular to the water flow $S_n$ to wall area of netting S, was derived based on the numerical and experimental analysis of the wake flow through a netting twine simplified by a cylinder and a netting panel. The velocity was reduced in accordance with the velocity reduction factor when the flow passed the netting panel upstream of a cage net. The proposed method for the calculation of fluid force acting on a square cage net was based upon the assumption that it could be divided into four side panels and one bottom panel. It was proved that the force could be calculated by the sum of the drag forces acting on the individual netting panels.

• Asian-Australasian Journal of Animal Sciences
• /
• v.33 no.4
• /
• pp.556-567
• /
• 2020

Objective: To improve the utility of native grass resources as feed in China, we investigated the dynamics of protein and carbohydrate fractions among Inner Mongolian native grasses, during ensiling and the aerobic stage, using the Cornell Net Carbohydrate and Protein System. Methods: Silages were prepared without or with lactic acid bacteria (LAB) inoculant. We analyzed the protein and carbohydrate fractions and fermentation quality of silages at 0, 5, 15, 20, 30, and 60 d of ensiling, and the stability at 0.5, 2, 5, and 10 d during the aerobic stage. Results: Inner Mongolian native grass contained 10.8% crude protein (CP) and 3.6% water-soluble carbohydrates (WSC) on a dry matter basis. During ensiling, pH and CP and WSC content decreased (p<0.05), whereas lactic acid and ammonia nitrogen (N) content increased (p<0.05). Non-protein N (PA) content increased significantly, whereas rapidly degraded true protein (PB₁), intermediately degraded true protein (PB₂), total carbohydrate (CHO), sugars (CA), starch (CB₁), and degradable cell wall carbohydrate (CB₂) content decreased during ensiling (p<0.05). At 30 d of ensiling, control and LAB-treated silages were well preserved and had lower pH (<4.2) and ammonia-N content (<0.4 g/kg of fresh matter [FM]) and higher lactic acid content (>1.0% of FM). During the aerobic stage, CP, extract ether, WSC, lactic acid, acetic acid, PB₁, PB₂, true protein degraded slowly (PB₃), CHO, CA, CB₁, and CB₂ content decreased significantly in all silages, whereas pH, ammonia-N, PA, and bound true protein (PC) content increased significantly. Conclusion: Control and LAB-treated silages produced similar results in terms of fermentation quality, aerobic stability, and protein and carbohydrate fractions. Inner Mongolian native grass produced good silage, nutrients were preserved during ensiling and protein and carbohydrate losses largely occurred during the aerobic stage.

• Restorative Dentistry and Endodontics
• /
• v.35 no.4
• /
• pp.257-266
• /
• 2010

The purpose of this study was to determine the effect of post types and sizes on fracture resistance in immature tooth model with various restorative techniques. Bovine incisors were sectioned 8 mm above and 12 mm below the cementoenamel junction to simulate immature tooth model. To compare various post-and-core restorations, canals were restored with gutta-percha and resin core, or reinforced dentin wall with dual-cured resin composite, followed by placement of D.T. LIGHT-POST, ParaPost XT, and various sizes of EverStick Post individually. All of specimens were stored in the distilled water for 72 hours and underwent 6,000 thermal cycles. After simulation of periodontal ligament structure with polyether impression material, compressive load was applied at 45 degrees to the long axis of the specimen until fracture was occurred. Experimental groups reinforced with post and composite resin were shown significantly higher fracture strength than gutta-percha group without post placement (p < 0.05). Most specimens fractured limited to cervical third of roots. Post types did not influence on fracture resistance and fracture level significantly when cement space was filled with dual-cured resin composite. In addition, no statistically significant differences were seen between customized and standardized glass fiber posts, which cement spaces were filled with resin cement or composite resin individually. Therefore, root reinforcement procedures as above in immature teeth improved fracture resistance regardless of post types and sizes.

• Journal of the Institute of Convergence Signal Processing
• /
• v.4 no.1
• /
• pp.15-26
• /
• 2003

Ultrasonic inspection methods are widely used for detecting flaws in materials. The signal analysis step plays a crucial part in the data interpretation process. A number of signal processing methods have been proposed to classify ultrasonic flaw signals. One of the more popular methods involves the extraction of an appropriate set of features followed by the use of a neural network for the classification of the signals in the feature space. This paper describes an alternative approach which uses the least mean square (LMS) method and expectation maximization (EM) algorithm with the model based deconvolution which is employed for classifying nondestructive evaluation (NDE) signals from steam generator tubes in a nuclear power plant. The signals due to cracks and deposits are not significantly different. These signals must be discriminated to prevent from happening a huge disaster such as contamination of water or explosion. A model based deconvolution has been described to facilitate comparison of classification results. The method uses the space alternating generalized expectation maximization (SAGE) algorithm In conjunction with the Newton-Raphson method which uses the Hessian parameter resulting in fast convergence to estimate the time of flight and the distance between the tube wall and the ultrasonic sensor Results using these schemes for the classification of ultrasonic signals from cracks and deposits within steam generator tubes are presented and showed a reasonable performances.

• Journal of Korean Society of Forest Science
• /
• v.95 no.3
• /
• pp.358-364
• /
• 2006

This study was conducted to develop optimal solid culture medium for Tricholoma matsutake. As the solid matrix, granitic soil, perlite, vermiculate, pine sawdust and peat moss were compared regarding their effected on mycelial growth. Ergosterol content which is a fungal wall component was used as the growth index of the mycelia. Among the various solid matrixes, the granitic soil, perlite and mixture of the two supported the growth most. Barely flour appeared to be very effective on the stimulating of the mycelial growth when added to the solid matrix. An mixture of the matrix contained an even (1:1:1:1, v/v/v/v) mixture of granitic soil, perlite, vermiculate and pine sawdust. T. matsutake started growth 2 weeks after inoculation and reached stationary growth phase after 8th weeks in the solid matrix mixture. The mycelial density in the solid matrix was 7 times higher than that in fairy-ring soil. In addition, 30~70% water content and 10% humus soil in the solid matrix also supported good growth suggesting that T. matsutake needs humus soil for a nutrient sources. The solid matrix developed in the present study could be used to study physiological characteristics of T. matsutake as well.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.20 no.4
• /
• pp.341-347
• /
• 1987

The behavior of conger eel, Astroconger myriaster (Brevoort), to the bamboo and plastic pots with baits was investigated alternately in two experimental water tanks. One of the pots being dropped on the tank bottom, the eels touched it to obtain the bait probably by their sense of smell, and increased rapidly in the number of touch to show a maximum within 30 minutes. But the touch was made mainly to the pot wall at which the bait was located and quite accidentally to the pot mouth. The eels touched the pot mouth retreated frequently without attempting to enter the pot and their entering was very hampered by the bamboo funnel constituting the pot mouth. However, a entering, if made, encouraged other touches and the touches ascribed other enterings. But, if 30 minutes elapsed, the number of touch decreased gradually and so the enterings were little made. The ability of pots attracting the eels into them was varied with their inclination to the tank bottom and the bait position in them. That is, the pot which was laid horizontally showed high ability of attracting in case in which the bait was fixed in the vicinity of its mouth. The pot, inclined by $30^{\circ}$ by lifting its tail and had a bait left free, showed almost equal ability to the horizontal pot with a bait in the vicinity of mouth. But the pot, inclined by $30^{\circ}$ by lifting its mouth and had a bait left free, showed a very low attracting. A comparison between the bamboo and plastic pots gave only that the entering of the eels became later several minutes in the latter.

• Asian-Australasian Journal of Animal Sciences
• /
• v.17 no.3
• /
• pp.355-365
• /
• 2004

Two experiments were conducted to determine the effect of alkaline hydrogen peroxide (AHP) treatment (1% NaOH+1.5% $H_2O_2$; 1 AHPMS, 2% NaOH+1.5% $H_2O_2$; 2AHPMS) on rate and extent of degradation of mustard straw (MS) in sacco in sheep, and its in vivo digestion and ruminal fermentation characteristics when fed to sheep with concentrate (200 g per sheep daily). The treatment of straw with 1 and 2% AHP increased its sodium content by 148 and 296% to that of untreated straw (UMS). There was significant decrease in NDF and hemicellulose contents of AHP treated straw and increase in cellulose and lignin contents. Phenolic acids like ferrulic, $\rho$-coumaric and o-coumaric significantly (p<0.001) reduced by AHP treatment of mustard straw. In first experiment the in sacco degradation of DM, OM and NDF was significantly (p<0.01) greater for 2 AHPMS than for UMS at all incubation periods. The disappearance of nutrient from 1 AHPMS and 2 AHPMS treated straws continue to increase up to 96 h whereas in UMS the peak disappearance was found at 48 h. By using the equation {(y=a+b) ($1-e^{-ct}$)} the degradation rates (c) for DM, OM, and NDF were significantly higher for UMS than AHP treated straws. Level of alkali (1 and 2%) had significant effect on degradation characteristics (a, b, c and $P_{0.05}$) of DM and NDF fraction of MS. However, the effect was not pronounced on OM fraction of MS. In feeding experiment, the intake of nutrients for DM, OM, cell wall constituents and energy was higher on 2 AHPMS, whereas no effect on the digestibility of these nutrients was observed. The apparent nitrogen retention was higher (p<0.05) both in 1 and 2 AHPMS groups. Water intake by animals was significantly increased due to AHP treated mustard straw feeding. Rumen liquor pH was higher in 2 AHPMS fed animals. The $NH_3-N$ of rumen liquor was not affected by feeding of AHP treated MS based diets. Total VFA concentration was significantly (p<0.01) higher in UMS fed group. The fractional out flow rate of DM was higher (p<0.05) in animals fed on 2 AHPMS diets compared to UMS and lAHPMS fed groups. The population of large holotrichs was higher (p<0.05) on AHP treated MS fed diets compared to UMS. The study indicated that treatment of mustard straw with AHP changed its chemical composition towards a better feed. The nutritive value of 2% AHP treated mustard straw was better in terms of dry matter intake and apparent nitrogen retention. The higher in sacco DM, OM and NDF disappearance however, was not confirmed by in vivo data in this study.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.62-62
• /
• 2009

석탄화력발전소의 CO2배출량 감소와 고효율, 대용량화로 인해 초초임계압(USC:Ultra Super Critical) 화력발전소의 건설이 증가하고 있다. USC 발전소는 효율향상을 위한 증기온도와 압력의 상승 때문에 보일러 고온고압부에 기존의 소재에 비해 고온강도와 내산화성의 재료물성이 향상된 신소재 적용이 불가피하다. 특히 사용된 신소재 중에서 보일러 본체를 구성하는 수냉벽관(Water wall), 과열기와, 재열기용 튜브 및 후육부인 헤더와 배관재로 기존의 2.25Cr-1Mo강을 개량한 2.25Cr-1.6W계 내열강이 적용되고 있다. 2.25Cr-1.6W강은 SMI와 MHI가 공동개발한 소재로 1995년 튜브제품이, 1999년에 단조, 파이프재, 플레이트제품이 ASME code case로 등재되었고, 2009년 ASME code case 2199-4로 개정되어 사용 중이다. 이 소재는 2.25Cr-1Mo강에 고온강도 개선을 위해 석출강화효과가 있는 V과 Nb을 첨가하였고, 탄화물의 열적안정성과 고용강화효과 증대를 위해 W을 첨가하였다. 그리고 제작성과 용접성 및 재료의 인성 향상을 위해 B첨가와 C함량을 낮추었다. 합금성분의 첨가와 조정에 의해 고온강도는 개선되었지만, 보일러 설치 및 보수를 위한 용접과정에서 용접금속과 CGHAZ(Coarse Grain HAZ)에서 용접균열이 발생하였다. 대부분의 용접균열은 용접결함이나 고온 혹은 저온균열이 아닌 2.25Cr-1.6W계강의 강도 개선을 위해 첨가한 V과 Nb이 용접후열처리 도중 입내에 MX형태의 미세석출로 입내를 강화시킴으로서 발생한 재열균열 민감성 증대에 기인된 것으로 판단된다. 이에 본 연구에서 용접 및 후열처리 과정에서 용접금속과 HAZ에서 발생하는 용접금속의 응력분포를 전산해석을 통해 확인하고 실제 후육파이프 용접부에서 잔류응력을 측정해 비교하였다. 용접부 응력분포는 SYSWELD 프로그램을 사용해 해석을 수행하였고, 발전소 실배관재의 용접부 응력측정은 수평부 측정이 용이하도록 지그를 부착한 Potable 잔류응력측정기를 사용해 Hole Drilling Method(HDM)를 적용하여 잔류응력을 측정하였다. 해석 결과 CGHAZ부위의 잔류응력이 용접금속과 기타 부위에 비해 높은 응력분포를 나타냈으며, 이는 CGHAZ와 용접용융선 부근에서 균열이 발생하는 실제값과 일치하는 결과를 보였다. 실제 배관재 용접부에서 측정한 잔류응력값은 항복응력의 약 50% 이하 응력값을 나타냈다. 배관 구조에 기인한 시스템응력의 영향을 제거하기 위해 배관재 용접부를 중심으로 양끝단을 절단 후 용접부에서 측정한 응력은 항복응력 대비 25%수준의 낮은값을 보였다. 그러나 배관재가 장기간 고온환경에 노출되었고 용접금속 내부의 균열이 발생한 상태에서 측정하였기 때문에 용접잔류응력은 상당부분 해소되어 상대적으로 낮은 응력값이 얻어진 것으로 판단된다.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.4
• /
• pp.571-588
• /
• 2016

Eucalyptus pellita F. Muell is one of pulp woods that is being developed through breeding plantation programs in Indonesia. The research aimed at exploring the chemical and morphological characteristics of fiber, and to determine the rank of plus trees from 4 provenances based on the suitability for pulps. The materials included the plus trees of E. pellita (9 years) from the 2nd generation of progeny tests in Pelaihari, South Borneo. Wood properties under investigation included the chemical properties and morphological fiber characteristics (fiber dimensions and its derived properties). In the present study, data were analyzed using descriptive statistic, Analytic Hierarchy Process (AHP) and Pearson's correlation. Results showed that the chemical properties of E. pellita, i.e. the contents of ethanol-toluene extractives, hot water soluble extractives, holocellulose, alphacelullose, and lignin were $3.08{\pm}1.00%$, $1.41{\pm}0.38%$, $75.26{\pm}2.58%$, $49.02{\pm}2.88%$, and $29.49{\pm}1.86%$, respectively. The average values of wood fiber morphology were $1.02{\pm}0.08$ mm (fiber length), $13.25{\pm}1.64{\mu}m$ (fiber diameter), of $6.94{\pm}1.70{\mu}m$ (lumen diameter), $3.15{\pm}0.52{\mu}m$ (fiber wall thickness), $0.97{\pm}0.30$ (Runkel ratio), $0.57{\pm}0.10$ (Luce's shape factor), $78.21{\pm}10.34$ (slenderness ratio) and $130.91{\pm}33.77{\times}10^3{\mu}m^3$ (solids factor). The AHP scoring rank indicated that the best individuals were 28.4.3.28 (Kiriwo Utara), 12.1.5.28 (North Kiriwo), 19.11.5.45 (Serisa Village), 3.8.4.9 (South Kiriwo), and 6.6.3.15 (South Kiriwo). Pearson correlation analysis showed significant correlations between the levels of fiber length with alpha-cellulose content (r = 0.39) as well as the fiber length with ethanol-toluene extractive contents (r = -0.41).

• Journal of the Korean Society for Nondestructive Testing
• /
• v.25 no.1
• /
• pp.27-35
• /
• 2005

Ultrasonic inspection methods are widely used for detecting flaws in materials. The signal analysis step plays a crucial part in the data interpretation process. A number of signal processing methods have been proposed to classify ultrasonic flaw signals. One of the more popular methods involves the extraction of an appropriate set of features followed by the use of a neural network for the classification of the signals in the feature spare. This paper describes an alternative approach which uses the least mean square (LMS) method and exportation maximization (EM) algorithm with the model based deconvolution which is employed for classifying nondestructive evaluation (NDE) signals from steam generator tubes in a nuclear power plant. The signals due to cracks and deposits are not significantly different. These signals must be discriminated to prevent from happening a huge disaster such as contamination of water or explosion. A model based deconvolution has been described to facilitate comparison of classification results. The method uses the space alternating generalized expectation maximiBation (SAGE) algorithm ill conjunction with the Newton-Raphson method which uses the Hessian parameter resulting in fast convergence to estimate the time of flight and the distance between the tube wall and the ultrasonic sensor. Results using these schemes for the classification of ultrasonic signals from cracks and deposits within steam generator tubes are presented and showed a reasonable performances.