• Journal of Sensor Science and Technology
• /
• v.28 no.2
• /
• pp.101-105
• /
• 2019

ZnS substrates with excellent transmittance in the mid-infrared region ($3-5{\mu}m$) were prepared using hot pressing instead of conventional chemical vapor deposition (CVD). Diamond-like carbon(DLC) was coated on either one or both sides of the ZnS substrates to improve their mechanical properties and transmittance. More specifically DLC was coated using CVD with an Ar and $C_2H_2$ mixed gas, and Ge was used as the bonding layer. During CVD, the bias voltage was fixed to 500 V and analyzed by Fourier transform infrared spectroscopy (FT-IR), nanoindenter, scanning electron microscope and energy dispersive spectrometry. Results of hardness analysis using the nanoindenter, showed that DLC coating increased from 5.9 to 17.7 GPa after deposition. The FT-IR spectroscopy results showed that, in the mid-infrared region ($3-5{\mu}m$), the average transmittance of the samples with DLC coating on one and both sides increased by approximately 6% and approximately 11.2% respectively. In conclusion, the DLC coating improved the durability and transmittance of the ZnS substrates.

• Transactions on Electrical and Electronic Materials
• /
• v.5 no.4
• /
• pp.153-157
• /
• 2004

ITO thin films were deposited on PET and soda-lime glass substrates by a dc reactive magnetron sputtering of In-Sn alloy metal target without substrate heater and post-deposition thermal treatment. The dependency of rf-bias voltage and substrate power during deposition processing was investigated to control the electrical and optical properties of ITO films. The range of rf bias voltage is from 0 to -80 V and the substrate power is applied from 10 to 50 W. The minimum resistivity of ITO film is 5.4${\times}$10$^{-4}$ $\Omega$cm at 50 W power and rf-bias voltage of -20 V. The best transmittance of ITO films at 550 nm wavelength is 91 % in the substrate power of 30 W and rf-bias voltage of -80 V.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.113-116
• /
• 1998

In this paper, we studied the electro-optical(EO) performance of photo-aligned twisted nematic(TN)-liquid crystal display(LCD) with oblique non-polarized ultraviolet(UV) light irradiation on polyimide(Pl) surface. We observed that the voltage-transmittance and response time characteristics of photo-aligned TN-LCD is almost same compared to conventional TN-LCD. Also, we observed that the voltage-holding-ratio(VHR) of photo-aligned TN-LCD is almost same compared to conventional TN-LCD.

• Korean Journal of Materials Research
• /
• v.24 no.12
• /
• pp.715-719
• /
• 2014

(PDDA/$SiO_2$) thin films that consisted of positively charged poly (diallyldimethylammonium chloride) (PDDA) and negatively charged $SiO_2$ nanoparticles were fabricated on a glass substrate by an applying voltage layer-by-layer (LBL) self-assembly method. In this study, the microstructure and optical properties of the (PDDA/$SiO_2$) thin films coated on glass substrate were measured as a function of the applied voltage on the Pt electrodes. When 1.0 V was applied to a Pt electrode in a PDDA and $SiO_2$ solution, the thickness of the $(PDDA/SiO_2)_{10}$ thin film increased from 79 nm to 166 nm. The surface roughness also increased from 15.21 nm to 33.25 nm because the adsorption volume of the oppositely charged PDDA and $SiO_2$ solution increased. Especially, when the voltage was applied to the Pt electrode in the $SiO_2$ solution, the thickness increase of the (PDDA/$SiO_2$) thin film was larger than that obtained when using the PDDA solution. The refractive index of the fabricated (PDDA/$SiO_2$) thin film was ca. n = 1.31~1.32. The transmittance of the glass substrate coated by (PDDA/$SiO_2$)6 thin film with a thickness of 106 nm increased from ca. 91.37 to 95.74% in the visible range.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1461-1462
• /
• 2011

In this paper, in order to obtain the excellent transparent conducting film with low resistivity and high optical transmittance for dye sensitized solar cell, ITiO thin films were deposited on Corning glass substrate by rf magnetron sputtering method. The effects of the discharge power and gas pressure on the electrical and optical properties were investigated experimentally. Particularly in order to lower the electrical resistivity, the effect of heat treatment and bias voltage on the morphological properties of ITiO thin film were also studied and discussed. The concentration ratio (%) for In, Ti, and O was 27 : 2 : 42. The electrical resistivity of $2{\times}10^{-4}{\Omega}{\cdot}cm$ and 90% of optical transmittance were obtained under the conditions of 5mTorr of gas pressure, 300W of discharge power, $300^{\circ}C$ of substrate temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.1054-1057
• /
• 2003

We have studied $90^{\circ}$ twisted nematic (TN) mode driven by fringe electric field, where two polarizers are parallel each other such that the cell shows a black state before a voltage is applied. According to the studies by computer simulation for a LC with negative dielectric anisotropy, the LC twists perpendicular to the horizontal field direction of fringe electric field and the degree of tilt angle is very low, when a voltage is applied. Therefore, the new device exhibits wide viewing angle characteristic due to in-plane switching and high transmittance since the LC director aligns parallel to the polarizer axis.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05a
• /
• pp.185-188
• /
• 2005

We synthesized the two types of photoalignment material of high thermal resistance with hydroxyl aromatic polyimide, and studied the liquid crystal (LC) aligning capabilities on the photopolymer layers. Also, electro-optical (EO) performances for the twisted-nematic (TN)-liquid crystal display (LCD) photoaligned with linearly polarized UV exposure were investigated. A good LC alignment with UV exposure on the two types of photopolymer surface can be obtained. The Voltage-transmittance (V-T) curve in the photoaligned TN cell with UV exposure was different from two type. The response time of photoaligned TN cell was measured about 21 ms in two alkyl chain and about 15ms in four alkyl chain.

• Transactions on Electrical and Electronic Materials
• /
• v.9 no.5
• /
• pp.198-201
• /
• 2008

The electro-optical (EO) characteristics of the one-side rubbing twisted nematic (TN) - liquid crystal display (LCD) on the polyimide (PI) surface with one-side ion beam (IB) irradiation were successfully studied. The good LC alignment for the one-side rubbing TN-LCD on the PI surface with one-side IB irradiation was observed. The suitable transmittance-voltage curves for the one-side rubbing TN-LCD on the PI surface with one-side IB irradiation were measured. Also, the good response time characteristics of the one-side rubbing TN-LCD on the PI surface with one-side IB irradiation were measured. The fast response time can be achieved for the one-side rubbing TN-LCD on the PI surface with one-side IB irradiation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.04a
• /
• pp.53-54
• /
• 2008

We have studied electro-optic characteristics as a function of passivation thickness$(t_p)$ in the fringe-field swiching (FFS) mode using the LC with positive dielectric anisotropy. When $t_p$ is increased from $0.29{\mu}m$ to $3.0{\mu}m$, a maximum transmittance is slightly increased to $2{\mu}m$. However, operating voltage is continuously increased up to above 11v. We found that the tilt angle is decreased between the edge of pixel electrode and the center of each pixel electrode. In the FFS mode using the liquid crystal with positive dielectric anisotropy, transmittance is affected by the tilt angle. When tilt angle is increased, transmittance become decrease. Therefore, in the FFS device, a low tilt angle is favored for high transmittance. It is demonstrated that the suitable passivation thickness make a tilt angle decreased.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.3
• /
• pp.23-29
• /
• 2020

Electrochromic (EC) device is an element whose transmittance is changed by electrical energy. Coloring and decoloring states can be easily controlled and thus used in buildings and automobiles for energy saving. There exist several types of EC devices; EC using electrolytes, polymer dispersed liquid crystal (PDLC), and suspended particle device (SPD) using polarized molecules. However, these devices involve solutions such as electrolytes and liquid crystals, limiting their applications in high temperature environments. In this study, we have studied all-solid-state EC device based on Tin(IV) oxide (SnO₂). A coloring phase is achieved when electrons are accumulated in the ultraviolet (UV)-treated SnO₂ layer, whereas a decoloring mode is obtained when electrons are empty there. The UV treatment of SnO₂ layer brings in a number of localized states in the bandgap, which traps electrons near the conduction band. The SnO₂-based EC device shows a transmittance of 70.7% in the decoloring mode and 41% in the coloring mode at a voltage of 2.5 V. We have achieved a transmittance change as large as 29.7% at the wavelength of 550 nm. It also exhibits fast and stable driving characteristics, which have been demonstrated by the cyclic experiments of coloration and decoloration. It has also showed the memory effects induced by the insulating layer of titanium dioxide (TiO₂) and silicone (Si).