• 한국전기전자재료학회논문지
• /
• 제11권11호
• /
• pp.969-974
• /
• 1998

The effects of $La_2O_3$on the microstructure and electrical characteristics of Pr-based ZnO varistors were investigated. The average grain size increased in the range of 21.9~56.3$\mu$ m with increasing $La_2O_3$additive content(0.0~2.0 mol%). La was, of course grain boundary, largely segregated at the nodal point. As $La_2O_3$additive content increases, threshold voltage and nonlinear coefficient decreased and leakage current increased. In particular, 2.0 mol% $La_2O_3$-added varistor exhibited low threshold voltage 17.0V/mm and nonlinear coefficient of about 6. Based on these results, this varistor can be said to be used as low-voltage varistor, if nonlinear coefficient is somewhat improved forward.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권2호
• /
• pp.109-116
• /
• 1999

ZnO Varistor is an electronic ceramic device to absorb the surge voltage from low voltage to high. To investigate the puncture mechanism occurring in NnO varistor, the Voronoi simulation for formulating the relation between the applied voltage and the increase of the temperature inside grain is applied. The Voronoi network can realize the structure of the practical varistor better than the established simple network. Using the current through each grain and the voltage applied to the grain, Joule heating energy is calculated and the phenomenon that the puncture occurs can be analyzed quantitatively by simulating the electric and thermal characteristics according to the externally applied pulsed voltage.

• The Korean Journal of Ceramics
• /
• 제4권1호
• /
• pp.47-52
• /
• 1998

The nonuniformity of energy absorption capability of ZnO varistor is systematically discussed in this paper. The nonuniformity of electrical characteristics and microstructure leads to decrease the energy absorption capability of ZnO varistor. The energy absorption capabilities were measured under different current waves, the experimental results stated that they have highly scattered phenomena. The influences of varistor surface area and nonuniformity of electrical characteristics to the energy absorption capability and the nonuniformity of commercial ZnO varistors were analyzed. There is a high nonuniformity existing in the energy absorption capability of commercial ZnO varistors.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 추계학술대회 논문집 Vol.15
• /
• pp.330-333
• /
• 2002

The stability against DC accelerated aging stress of $Dy_{2}O_{3}-doped$ $ZnO-Pr_{6}O_{11}-based$ varistor ceramics was investigated. The calculated nonlinear exponent$(\alpha)$ in varistor ceramics without $Dy_{2}O_{3}$ was only 4.9, whereas the $\alpha$ value of the varistors with $Dy_{2}O_{3}$ was abruptly increased in the range of 48.8 to 58.6. The varistor ceramics with $Dy_{2}O_{3}$ content of 1.0 mol% exhibited maximum ${\alpha}$, reaching 58.6, whereas they exhibited very poor stability. While, The varistor ceramics doped with 0.5 mol% $Dy_{2}O_{3}$ exhibited not only the high nonlinearity, which the ${\alpha}$ is 55.3 and the leakage current is $0.1{\mu}A$， but also the highest stability, which the variation rates of varistor voltage and nonlinear exponent are -0.8% and -14.3%, respectively, under DC accelerated aging stress, $0.95 V_{1mA}/150^{\circ}C/24h$.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1986년도 하계학술대회논문집
• /
• pp.379-381
• /
• 1986

• Transactions on Electrical and Electronic Materials
• /
• 제16권6호
• /
• pp.308-311
• /
• 2015

V₂O₅/Mn₃O₄/Nb₂O₅ codoped zinc oxide varistor ceramics were sintered at a temperature range as low as 875~950℃. The voltage clamping characteristics of V₂O₅/Mn₃O₄/Nb₂O₅ codoped zinc oxide varistor ceramics were investigated at a pulse current range of 1~50 A. The sintering temperature had a significant effect on clamp voltage ratio, which exhibits surge protection capabilities. The varistor ceramics sintered at 875℃ exhibited the best clamping characteristics, in which the clamp voltage ratio was 2.69 at a pulse current of 50 A. The varistor ceramics sintered at 900℃ exhibited the highest electrical stability, where = 3,824 V/cm (initial 3,909 V/cm), and E_{1 mA/cm²} = 27 (initial 39) after application of a pulse current of 100 A.

• 한국전기전자재료학회논문지
• /
• 제15권9호
• /
• pp.776-782
• /
• 2002

The microstructure, V-Ι characteristics, and stability of ZnO-P $r_{6}$ $O_{11}$ CoO-C $r_2$ $O_3$- $Y_2$ $O_3$-based varistor ceramics were investigated with cooling rate in the range of 2~8$^{\circ}C$/min. The cooling rate relatively weakly affected the microstructure, the varistor voltage, and the leakage current in the V-Ι characteristics. But the nonlinear exponent relatively strongly affected by cooling rate. The cooling rate also greatly affected the stability of V-Ιand dielectric characteristics for DC accelerated aging stress. On the whole, the varistors cooled with 4$^{\circ}C$/fin exhibited the highest performance in the densification, nonlinearity, and stability. Especially, they exhibited a high stability, in which the variation rate of the varistor voltage( $V_{1㎃}$), the nonlinear exponent($\alpha$), and the dissipation factor(tan $\delta$) is -1.4%, -4.9%, and ＋60.0%, respectively, under DC accelerated aging stress such as 0.95 $V_{1㎃}$15$0^{\circ}C$/12 h)

• 한국전기전자재료학회논문지
• /
• 제30권12호
• /
• pp.817-821
• /
• 2017

As a ZnO varistor is subjected to electrical and environmental stresses, it degrades gradually, which may result in power interruption by short circuit. This study investigates changes in the electrical characteristics of ZnO varistors due to deterioration owing to energy absorption, and determines the optimal parameters for on-line diagnosis of the varistor. Two types of varistors were used for an accelerated aging experiment involving the application of the $8/20{\mu}s$ standard lightning impulse current. The electrical characteristics in terms of the reference voltage, total leakage current, resistive leakage current, and third-harmonic component of the total leakage current were measured, and their change rates were analyzed. The results revealed that the total leakage current increased slightly with an increase in the varistor absorbed energy, while the resistive leakage current and the third-harmonic component increased apparently. Therefore, the third-harmonic component of the total leakage current was proposed as the optimal parameter for on-line monitoring of ZnO varistor conditions.

• 한국전기전자재료학회논문지
• /
• 제20권6호
• /
• pp.496-501
• /
• 2007

In order to enhance sintering characteristics on the $ZnO-Pr_6O_{11}$ based multilayer chip varistors (MLVs), a response surface analysis using central composite design method were carried out. As a result, varistor voltage($V_{1mA}$), nonlinear coefficient ($\alpha$), leakage current ($I_L$) and capacitance (C) were considered to be mainly affected by sintered temperature and holding time. MLVs sintered at $1200^{\circ}C$ and above $1200^{\circ}C$ revealed poor electrical characteristics, possibly due to the reaction between electrode materials(Pd) and $ZnO-Pr_6O_{11}$ based ceramics. On the sintering temperature range $1150{\sim}1175^{\circ}C$, nonlinear coefficient ($\alpha$) and leakage current ($I_L$) were shown to be $60{\sim}69$ and below $0.3{\mu}A$, respectively. In particular, MLVs sintered at $1175^{\circ}C$, 1.5 hr and $2^{\circ}C/hr$ (cooling speed) showed stable ESD(Electrical Static Discharge) characteristics under the condition of 10 times at 8 Kv with deviation varistor voltage, and deviation nonlinear coefficient were 0.3% and 0.33% (at positive), 0.55% (at negative), respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 추계학술대회 논문집 Vol.17
• /
• pp.408-411
• /
• 2004

The electrical stability against surge stress of ZPCCY-based varistors were investigated at different sintering times. Sintering time decreased the varistor voltage and nonlinear exponent from 279.6 to 179.1 and from 52.5 to 24.9, respectively. On the contrary, the leakage current and dielectric dissipation factor increased from 1.2 to 9.8 ${\mu}A$ and from 0.0461 to 0.0651 with increase of sintering time. For all varistors, the variation rates of V-I characteristic parameters against surge stress were affected in order of varistor voltage$\rightarrow$nonlnear exponent$\rightarrow$leakage current. On the whole, the electrical stability against surge stress increased with increasing sintering time. Conclusively, it is assumed that the varistor sintered for 2 h exhibited comparatively good characteristics, in view of overall characteristics.