• Applied Microscopy
• /
• v.25 no.2
• /
• pp.65-72
• /
• 1995

The interfacial structures of ZnSe/GaAs which were grown by single chamber MBE at $300^{\circ}C$ were investigated by high resolution transmission electron microscope working at 300 kV with resolution of 0.18 nm. The interfaces of ZnSe/GaAs whose thickness is 2,700 nm are wavy and extensive stacking faults were formed in ZnSe epilayer but the interfaces maintained the coherency with the substrate GaAs. The stacking faults are formed in {111} planes and their sizes are $10{\sim}20nm$ in length and two or three atomic layer in width with the density of $10^9/cm^2$. Micortwins and moire fringes are also observed. However. in 10 nm ZnSe epilayer, the interfaces are pseudomorphic and only moire fringes are observed in local areas. The cylindrical defects which are perpendicular to the interface with $50{\sim}60nm$ in length, were observed with the interval of 50 nm at ZnSe/GaAs interfaces in 2,700nm epilayer. The origin and character of these defects are unknown, however, they played a role of producing the structural defects at the interfaces.

• Journal of the Korean Electrochemical Society
• /
• v.6 no.2
• /
• pp.98-102
• /
• 2003

Urethane acrylate oligomer was synthesized and used in a gel polymer electrolyte (GPE) and then its electrochemical performances were evaluated. $LiCoO_2/GPE/graphite$ cells were prepared and their performances depending on discharge currents and temperatures were evaluated. The precursor containing $5 vol\%$ curable mixture had a low viscosity relatively. ionic conductivity of the gel polymer electrolyte at room temperature and $-20^{\circ}C$ was ca. $5.9\times10^{-3}S{\cdot}cm^{-1}\;and\;1.4times10^{-3}S{\cdot}cm^{-1}$, respectively. GPE showed good electrochemical stability up to potential of 4.5V vs. RLi/Li^+.\;LiCoO_2/GPE/graphite$ cell showed a good high-rate and low-temperature performance.

• Asian Journal of Atmospheric Environment
• /
• v.11 no.4
• /
• pp.217-234
• /
• 2017

Indoor air pollutants can cause severe health problems, specifically in terms of toxicological impacts on human. Every day, a complex mixture of many air pollutants is emitted from various sources and subject to atmospheric processes that can create varied classes of pollutants such as carboxylic acids, aldehydes, ketones, peroxyacetyl nitrate, and hydrocarbons. To adhere to indoor air quality standards, a number of techniques such as photocatalytic oxidation of various volatile organic compounds (VOCs) have been employed. Among these techniques, titania ($TiO_2$) based photocatalytic reactions have proven to be the best benchmark standard approach in the field of environmental applications. Over the last 45 years, $TiO_2$-based photocatalytic reactions have been explored for the degradation of various pollutants. This review discusses the indoor air quality profile, types of indoor pollutants, available indoor air cleaning approaches, and performance of $TiO_2$-based catalysts. Finally, we have presented the perspectives on the progress of $TiO_2$ induced photocatalysis for the purification of indoor air.

• Journal of Microbiology and Biotechnology
• /
• v.18 no.2
• /
• pp.283-286
• /
• 2008

The methylenetetrahydrofolate dehydrogenase/cyclohydrolase (MTHFDC) from the thermoacidophilic archaeon Thermoplasma acidophilum is a 30.6kDa molecular-mass enzyme that sequentially catalyzes the conversion of formyltetrahydrofollate to methylenetetrahydrofolate, with a preference for NADP as a cofactor, rather than NAD. In order to elucidate the functional and structural features of MTHFDC from archaeons at a molecular level, it was overexpressed in Escherichia coli and crystallized in the presence of its cofactor, NADP, at 295K using polyethylene glycol (PEG) 4000 as a precipitant. The crystal is a member of the monoclinic space group $P2_1$, with the following unit cell parameters: $a=66.333{\AA},\;b=52.868{\AA},\;c=86.099{\AA},\;and\;{\beta}=97.570^{\circ}$, and diffracts to a resolution of at least $2.40{\AA}$ at the synchrotron. Assuming a dimer in the crystallographic asymmetric unit, the calculated Matthews parameter $(V_M)\;was\;2.44{\AA}^3/Da$ and the solvent content was 49.7%.

• Electrical & Electronic Materials
• /
• v.8 no.4
• /
• pp.406-412
• /
• 1995

A n-CdS thin films were evaporated by thermal evaporation method and their structure, optical transmission spectra and electrical characteristics were investigated. The photovoltaic characteristics of solar cells which were fabricated in optimum conditions measured. The evaporated CdS thin films showed in hexagonal structure and above 80% of optical transmission spectra regardless of impurity doping. The high quality thin films could be obtained at 150.deg. C temperature of substrate, which is useful for solar cell window layer with low resistivity of 6*10$\^$-2/(.ohm.-cm) by In doping We measured the electrical and optical characteristics of the n-CdS/p-InP heterojunction solar cells. The most efficient photovoltaic characteristics of heterojunction solar cells had the open circuit voltage of 0.66V, short circuit current density of 13.85mA/cm$\^$2/, fill factor of 0.576 and conversion efficiency of 8.78% under 60mW/cm$\^$2/ illumination.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.740-742
• /
• 1998

In this paper, we described the effect of rapid thermal annealing on the electrical properties of interfacial layer between various top electrodes and $(Ba_{0.5}Sr_{0.5})TiO_3$ thin films. BST thin films were fabricated on Pt/TiN/$SiO_2$/Si substrate by RF magnetron sputtering technique. AI, Ag, and Cu films for the formation of top electrode were deposited on BST thin films by thermal evaporator. Top electrodes/BST/Pt capacitor annealed with rapid thermal annealing at various temperature. In $(Ba_{0.5}Sr_{0.5})TiO_3$ thin films with Cu top electrode annealed at $500^{\circ}C$, the dielectric constant was measured to the value of 366 at 1.2 [kHz] and the leakage current was obtained to the value of $5.85{\times}10^{-7}\;[A/cm^2}$ at the forward bias of 2 [V].

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.147-151
• /
• 1999

YBCO step-edge Josephson junction were fabricated on sapphire substrates. The steps were formed on R-plane sapphire substrates by using Ar ion milling with PR masks. The step angle was controlled in the wide range from 25$^{\circ}$ to 50$^{\circ}$ by adjusting both the Ar ion incident angle and the photoresist mask rotation angle relative to the incident Ar ion beam. CeO$_2$ buffer layer and in-situ YBa$_2Cu_3O_{7-{\delta}}$ (YBCO) thin films was deposited on the stepped R-plane sapphire substrates by pulsed laser deposition method. The YBCO film thickness was varied to obtain the ratio of film thickness to step height in the range from 0.5 to 1. The step edge junction exhibited RSJ-like behaviors with I$_cR_n$ product of 100 ${\sim}$ 300 ${\mu}$V, critical current density of 10$^3$ ${\sim}$ 10$^5$ A/ cm$^2$ at 77 K.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.44.2-44.2
• /
• 2011

고분자 전해질 연료전지는 다른 연료전지에 비해 작동온도가 낮고 전류밀도 및 출력밀도가 높으며 시동시간이 짧아서 다양한 분야에 응용이 가능할 것으로 기대된다. 그 중 양극판은 가격비와 중량비가 높아 부품 가격 및 중량을 낮출 경우 파급 효과가 높은 것으로 예상된다. 본 연구에서는 일반적으로 사용하고 있는 스테인리스강보다 가격이 저렴한 저탄소강을 모재로 이용하였다. 저탄소강은 자체로 내식성을 가지지 못하므로, 최근에 차세대 신소재로 각광을 받고 있는 그라핀(graphene)을 전기분무(electro spray coating)법으로 코팅하여 저탄소강의 내식성을 향상시키고자 하였다. 그라핀은 에탄올을 용매로 사용하여 분산하였으며, 분산제로 소량의 다이페닐다이에톡시실란(diphenyldiethoxysilane)을 첨가하여 코팅용액을 제작하였다. 코팅공정은 5~15 kV의 전압을 가하여 1시간동안 코팅을 진행하였으며, 그라핀-저탄소강의 미세구조를 주사전자현미경과 광학현미경을 통하여 관찰하였다. 또한 X-선 회절분석법을 이용하여 그라핀의 결정구조를 분석하였다. 한편 스택의 내부와 유사한 산화성 분위기를 모사하기 위해 $80^{\circ}C$의 0.1N $H_2SO_4$+2ppm $F^-$ 용액에서 내식성 실험을 수행하였고 면간접촉저항을 측정하였다. 그라핀이 코팅된 저탄소강 시편은 고분자 전해질 연료전지 양극판의 요구조건을 만족하였으며, 연료전지 양극판으로서의 사용가능성을 확인하였다.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05c
• /
• pp.513-518
• /
• 1996

저농도 방사성 액체폐기물의 최종 처리를 목적으로 본 연구에서는 면 35%와 Polyester 65%가 함유된 합성섬유를 증발매체로 하여 자연상태의 공기를 강제 송풍시키는 자연증발처리시설에서 증발에 영향을 미치는 주요 변수에 따라 증발 단위 면적당 Cs-137, Co-60을 함유한 방사성 폐액의 증발량측정 및 제염계수를 조사하였다. 증발효과는 유입공기의 습도가 낮고, 공기의 유속과 공급액의 유량이 증가하고 유입공기 및 폐액의 온도가 높아질수록 증발량이 증가하였다. 실험결과 유입된 공기는 1$0^{\circ}C$ 이상, 습도는 80% 이하, 공급폐액의 유량이 3.4 $\ell$/hr $m^2$ 이상, 공기유속은 1.14~l.47 m/sec 범위가 조업조건이며 이때 제염계수는 5.1 $\times$ $10^3$, 배출공기의 방사능 농도는 4.7$\times$$10^{-13}$ $\mu$Ci/$m\ell$ air로 측정되었다. 공급유량이 4.6$\ell$/hr.$m^2$와 공기유속이 1.47 m,/sec일때 최대 증발조건으로 나타났으며, 이때 증발량은 총 증발면적 11,250$m^2$ 에서 1.2 ㎥/hr로 측정되었으며 대기의 온.습도 및 풍속에 따른 실험을 통하여 달톤형 증발식의 Wind Factor ［Eh ＝ (0.0168 ＋ 0.0141V)$\Delta$H］를 도출하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.632-635
• /
• 2004

The purpose of this paper is to investigate the effect of arc current and contact velocity on the erosion of silver-based contact materials to be used in low voltage circuit breakers. The opening velocity during breaking, which is constant, ranges between 2m/s to 6m/s in the 415V $25kA_{rms}$. Contact erosion is evaluated by measuring the mass change of the cathode and anode. The results show that the increase in opening velocity from 2m/s to 6m/s leads to a decrease in the contact erosion. It is shown that the material transfer from one electrode to another depends on the transfer charge and the opening velocity of the contacts. The contact pairs of AgWC/AgCdO are superior to $AgWC/AgSnO_2In_2O_3$ or AgWC/AgC contact pairs in the contact erosion.