• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.5
• /
• pp.430-437
• /
• 2004

This thesis proposes novel SRP-PWM(Separately Random Pulse Position PWM) techniques and novel two-phase switching pattern applied to four-switch inverter, having various advantages such as operation time decrease that is required for decrease of switching damage, easy of implementation and inverter control at high frequency switching. In this thesis, we wish to confirm that SRP-PWM techniques disperse harmonic spectrum of inverter output current evenly into wide frequency area, that is, side-band of specification frequency. And we confirm the harmonic reduction effect of proposed techniques. Therefore, we will achieve an experiment by IGBT inverter using DSP and will verify the validity of proposed techniques compared with simulation results that use MATLAB/SIMULINK.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.1
• /
• pp.74-80
• /
• 2007

This paper proposes the novel open-fault detection/isolation scheme of inverter switch in two-phase excited VSI. This scheme identify open-fault using voltage sensor at lower switches of each phase according to the operating mode. It has benefit of simple implementation, fast detection and robustness in the load so that stab of the system is improved. Also, at faulty mode, it minimizes faulty effect and makes possible continuous operation through the reconfiguration procedure applying four-switch operation. The validity of proposed fault detection scheme is verified by experimental results.

• Journal of Power Electronics
• /
• v.17 no.3
• /
• pp.579-589
• /
• 2017

In this study a new high step-up dc-dc converter is presented. The operation of the proposed converter is based on the capacitor switching and coupled inductor with a single active power switch in its structure. A passive voltage clamp circuit with two capacitors and two diodes is used in the proposed converter for elevating the converter's voltage gain with the recovered energy of the leakage inductor, and for lowering the voltage stress on the power switch. A switch with a low $R_{DS}$ (on) can be adopted to reduce conduction losses. In the generalized mode of the proposed converter, to reach a desired voltage gain, capacitor stages with parallel charge and series discharge techniques are extended from both sides of secondary side of the coupled inductor. The proposed converter has the ability to alleviate the reverse recovery problem of diodes with circuit parameters. The operating principle and steady-states analyses are discussed in detail. A 40W prototype of the proposed converter is implemented in the laboratory to verify its operation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.3 no.4
• /
• pp.274-279
• /
• 2002

ATM packet switching technologies for the purpose of the B-ISDN service are focused on high performance which represents good qualities on throughput, packet loss, and packet delay. ATM switch designs on a class of parallel interconnection network have been researched. But these are based on the self-routing function of it. It leads to conflict with each other, and to lose the packets. Therefore, this paper proposes the method based on Sort-Banyan network should be adopted for optimal routing algorithm. It is difficult to expect good hardware complexity. For good performance, a switch design based on the development of new routing algorithm is required. For the design of switch network, the packet distributor and multiplane are proposed. They prevent each packet from blocking as being transmitted selectively by two step distributed decision algorithm. This switch will be proved to be a good performance switch network that internal blocking caused from self-routing function is removed. Also, it is expected to minimize the packet loss and decrease the packet delay according to packet transmission.

• Journal of Power Electronics
• /
• v.14 no.4
• /
• pp.661-670
• /
• 2014

A new DC/DC converter with zero voltage switching is proposed for applications with high input voltage and high load current. The proposed converter has two circuit modules that share load current and power rating. Interleaved pulse-width modulation (PWM) is adopted to generate switch control signals. Thus, ripple currents are reduced at the input and output sides. For high-voltage applications, each circuit module includes two half-bridge legs that are connected in series to reduce switch voltage rating to $V_{in}/2$. These legs are controlled with the use of asymmetric PWM. To reduce the current rating of rectifier diodes and share load current for high-load-current applications, two center-tapped rectifiers are adopted in each circuit module. The primary windings of two transformers are connected in series at the high voltage side to balance output inductor currents. Two series capacitors are adopted at the AC terminals of the two half-bridge legs to balance the two input capacitor voltages. The resonant behavior of the inductance and capacitance at the transition interval enable MOSFETs to be switched on under zero voltage switching. The circuit configuration, system characteristics, and design are discussed in detail. Experiments based on a laboratory prototype are conducted to verify the effectiveness of the proposed converter.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.73-74
• /
• 2016

This paper proposes a wide output range AC/DC converter for a rechargeable battery of electric vehicle. In the proposed wide output range AC/DC converter for rechargeable battery of electric vehicle, the main transformer in the DC/DC stage is divided by two. Therefore, if the switch is connected to the middle tap, then half of the maximum voltage is applied. Otherwise, it can be applied the full range of the high voltage by connecting the switch to the whole tab. And also, it is designed to have a wide output voltage range by applying Vin/2 made by changing the full-bridge to half-bridge by using the bridge change switch of the input stage. As it can be supplied the wide range output voltage with a single module, it has the advantage of space utilization and cost reduction effect.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.111-114
• /
• 2005

The isolation performance of the S-band single-pole single-throw (SPST) monolithic microwave integrated circuit (MMIC) switch with two different RF-interconnection approaches, microstrip and grounded coplanar waveguide (GCPW) lines, are investigated. On-to-off isolation is improved by 5.8 dB with the GCPW design compared with the microstrip design and additional improvement of 6.9dB is obtained with the coplanar wire-bond interconnection (CWBI) at 3.4 GHz. The measured insertion loss and third-order inter-modulation distortion (IMD3) are less than 2.43 dB over 2.5 CHz $\sim$ 4 GHz and greater than 64 dBc.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.10
• /
• pp.1664-1671
• /
• 2016

This paper presents the analysis of the gate-source voltage of the gallium nitride high electronic mobility transistor (GaN HEMT) in the half bridge structure focused on the mutual effects of two switching operation. Especially low side gate-source voltage is analyzed mathematically according to the high side switch turn-on and turn-off operation. Moreover, the influence of each gate resistance and parasitic component on the switching characteristic of other side switch is investigated, and the formula, simulation and experimental results are compared with theoretical data.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.505-507
• /
• 2008

A conventional active-clamp forward (ACF) converter is a favorable candidate in low-to-medium power applications. However, the switches suffer from high voltage stress, i.e., sum of the input voltage and the reset capacitor voltage. Therefore, it is not suitable for high input voltage applications such as a front-end converter of which the input voltage is about 400-$V_{dc}$. To solve this problem, three-switch ACF (TS-ACF) converter, which employs two main switches and one auxiliary switch with low voltage stress, is proposed. Utilizing low-voltage rated switches, the proposed converter is promising for high input voltage applications with high efficiency and low cost.

• Journal of Chest Surgery
• /
• v.27 no.7
• /
• pp.617-620
• /
• 1994

Approximately 10% of patients who have undergone atrial repair for transposition of the great arteries display easily identifiable RV dysfunction with or without TV incompetence by 10years. Treatment is difficult & the surgical options for this complication are limited. We experienced two cases of the reversal of atrial repair and conversion to an arterial switch after initial pulmonary artery banding. This surgical program is a realistic modality treating late failure of systemic right ventricle after atrial switch operation.