• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.425-425
• /
• 2008

Bismuth-antimony-telluride based thermoelectric thin film materials were prepared by metal organic vapor phase deposition using trimethylbismuth, triethylantimony and diisopropyltelluride as metal organic sources. A planar type thermoelectric device has been fabricated using p-type $Bi_{0.4}Sb_{1.6}Te_3$ and n-type $Bi_2Te_3$ thin films. Firstly, the p-type thermoelectric element was patterned after growth of $4{\mu}m$ thickness of $Bi_{0.4}Sb_{1.6}Te_3$ layer. Again n-type $Bi_2Te_3$ film was grown onto the patterned p-type thermoelectric film and n-type strips are formed by using selective chemical etchant for $Bi_2Te_3$. The top electrical connector was formed by thermally deposited metal film. The generator consists of 20 pairs of p- and n-type legs. We demonstrate complex structures of different conduction types of thermoelectric element on same substrate by two separate runs of MOCVD with etch-stop layer and selective etchant for n-type thermoelectric material. Device performance was evaluated on a number of thermoelectric devices. To demonstrate power generation, one side of the device was heated by heating block and the voltage output was measured. The highest estimated power of 1.3mW is obtained at the temperature difference of 45K. We provide a promising approach for fabricating thin film thermoelectric generators by using MOCVD grown thermoelectric materials which can employ nanostructures for high thermoelectric properties.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.3 no.4
• /
• pp.307-314
• /
• 1998

A novel high power factor Dual Half Bridge Series Resonant Inverter (DHB-SRI) for an induction heating appliance with multiple loads is proposed to remove the interferential acoustic noise caused by the difference between operating frequencies of adjacent loads. The circuit enables independent full power range control of two induction heating elements by one inverter circuit and has minimum switching losses due to the zero voltage switching characteristic. According to the mode analysis, I will explain the operation of the proposed circuit. To evaluate the required cooling capacity, loss analysis is performed through deriving some loss equations. In order to obtain the power factor correction capability and to lessen the system size, suitable design guides are given. Using the designed values, the proto-type circuit with 2.8kW power consumption for each induction heating element is built and tested to verify the operation of the proposed circuit.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.631-631
• /
• 2013

Battery has major drawbacks including its size and life expectancy, and environmental problem. As an alternative, energy harvesting is emerging as a potential solution to replace battery along with more energy-efficient IT devices. The idea of harnessing energy from our living environment is sustainable, semi-permanent, and eco-friendly. Also, unlike battery, energy harvester does not require much space to store energy. Therefore, energy harvesting can provide a better source of power for small, portable, and wireless devices. Among various ways of harvesting energy from our surroundings, triboelectricity is chosen due to its potential to be miniaturized, and efficient. Triboelectric effect occurs as two different materials with different polarity of charge separation come into contact through friction, and then become separated so that electric potential difference is achieved. In this research, such characteristic of triboelectricity is used as a way to convert ambient mechanical energy into electric energy.Series of recent researches have shown promising results that the triboelectric energy harvester can be simple and cost effective. However, sufficient electricity level required to operate mobile devices has not yet been achieved.In this research, our group focuses on the design and optimization of triboelectric energy harvesting device to enhance its output. By using maskless lithography to pattern Kapton film and silicon substrate, which is used as a mold for PDMS thin layer, and sputtering metal electrodes on each side, we fabricate and demonstrate different designs of triboelectric energy harvester that utilizes the contact electrification between a polymer thin film and a metal thin foil. In order to achieve optimized result, the output voltage and current are measured under diverse conditions, which include different surface structure and pattern, material, and the gap between layers.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.5
• /
• pp.443-447
• /
• 2009

Bismuth-antimony-telluride based thermoelectric thin film materials were prepared by metal organic vapor phase deposition using trimethylbismuth, triethylantimony and diisopropyltelluride as metal organic sources. A planar type thermoelectric device has been fabricated using p-type $Bi_{0.4}Sb_{1.6}Te_3$ and n-type $Bi_{2}Te_{3}$ thin films. Firstly, the p-type thermoelectric element was patterned after growth of $5{\mu}m$ thickness of $Bi_{0.4}Sb_{1.6}Te_3$ layer. Again n-type $Bi_{2}Te_{3}$ film was grown onto the patterned p-type thermoelectric film and n-type strips are formed by using selective chemical etchant for $Bi_{2}Te_{3}$. The top electrical connector was formed by thermally deposited metal film. The generator consists of 20 pairs of p- and n-type legs. We demonstrate complex structures of different conduction types of thermoelectric element on same substrate by two separate runs of MOCVD with etch-stop layer and selective etchant for n-type thermoelectric material. Device performance was evaluated on a number of thermoelectric devices. To demonstrate power generation, one side of the device was heated by heating block and the voltage output was measured. The highest estimated power of 1.3 ${\mu}m$ is obtained at the temperature difference of 45 K.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.2
• /
• pp.95-103
• /
• 2011

This paper proposes a 6b 1.2 GS/s 47.8 mW 0.17 $mm^2$ 65 nm CMOS ADC for high-rate wireless personal area network systems. The proposed ADC employs a source follower-free flash architecture with a wide input range of 1.0 $V_{p-p}$ at a 1.2 V supply voltage to minimize power consumption and high comparator offset effects in a nanometer CMOS technology. The track-and-hold circuits without source followers, the differential difference amplifiers with active loads in pre-amps, and the output averaging layout scheme properly handle a wide-range input signal with low distortion. The interpolation scheme halves the required number of pre-amps while three-stage cascaded latches implement a skew-free GS/s operation. The two-step bubble correction logic removes a maximum of three consecutive bubble code errors. The prototype ADC in a 65 nm CMOS demonstrates a measured DNL and INL within 0.77 LSB and 0.98 LSB, respectively. The ADC shows a maximum SNDR of 33.2 dB and a maximum SFDR of 44.7 dB at 1.2 GS/s. The ADC with an active die area of 0.17 $mm^2$ consumes 47.8 mW at 1.2 V and 1.2 GS/s.

• Korean Journal of Optics and Photonics
• /
• v.17 no.2
• /
• pp.181-185
• /
• 2006

A novel 60GHz optical carrier generator with a polarization domain-inverted structure is suggested and is demonstrated. The two arms of the Mach-Zehnder optical waveguide are periodically poled for quasi-phase velocity matching between the optical wave at 1550nm and the RF wave at 30 GHz. The center frequency of band-pass modulation and the 3 dB bandwidth of the fabricated modulator were measured to be 30.3 GHz and 5.1 GHz, respectively. Sub-carriers with the frequency difference of 60GHz waeregenerated under appropriate DC biac voltage application while the carrier was suppressed to lead to the power ratio between the modulated sub-carrier and the suppressed fundamental carrier of 28 dB, which proves that double sideband- suppressed carrier(DSB-SC) operation can be realized by the suggested single device.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1532-1534
• /
• 2003

We attempted to fabricate a dendrimer Langmuir-Blodgett(LB) films containing 48 pyridinepropanol functional end group. As the pyridinepropanol functional group could form a complex structure with metal ions. In this study the samples for electrical measurement were fabricated to two types metal complexes with $Pt^{4+}$ ions by LB method. And we have investigated the surface activity at the air-water interface as well as the electrical properties for the monolayers of G4-48PyP dendrimer complex with metal ions($Pt^{4+}$ ions) by different method. In the surface pressure-area(${\pi}$-A) isotherms of the dendrimers, the stable condensed films formed at the air-water interface and the different method of metal complex showed the difference on molecular behavior. We have studied the electrical properties of the ultra thin dendrimer LB films investigated by the current-voltage (I-V) characteristics of metal/dendrimer LB films/metal(MIM) structure. In conclusion, it is demonstrated that the metal ion around G4-48PyP dendrimer can contribute to make formation of network structure among dendrimers and it result from the change of electrical properties.

• Proceedings of the KIEE Conference
• /
• 2002.11a
• /
• pp.16-18
• /
• 2002

We attempted to fabricate a dendrimer Langmuir-Blodgett(LB) films containing 48 pyridinepropanol functional end group. As the pyridinepropanol functional group could form a complex structure with metal ions. In this study the samples for electrical measurement were fabricated to two types metal complexes with $Pt^{4+}$ and $Fe^{2+}$ ions by LB method. And we have investigated the surface activity at the air-water interface as well as the electrical properties for the monolayers of pure G4-48PyP dendrimer and its complex with metal ions($Pt^{4+}$ and $Fe^{2+}$ ions). In the surface pressure-area($\pi-A$) isotherms of the dendrimers, the stable condensed films formed at the air-water interface and the metal ions effect showed the difference on molecular behavior. We have studied the electrical properties of the ultra thin dendrimer LB films investigated by the current-voltage(I-V) characteristics of metal/dendrimer LB films/metal(MIM) structure. In conclusion, it is demonstrated that the metal ion around G4-48PyP dendrimer can contribute to make formation of network structure among dendrimers and it result from the change of electrical properties.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.3
• /
• pp.570-576
• /
• 2007

In this study, the characteristics of metal-ferroelectric-semiconductor FET (MFSFET) device is investigated using field-dependent polarization and square-law FET models. From drain current with the gate voltage variation, when coercive voltages of ferroelectric thin film are 0.5 and 1V, the memory windows are 1 and 2V, respectively. When the gate voltages are 0, 0.1, 0.2 and 0.3V, the difference of saturation drain currents of the MFSFET device at two threshold voltages in ID-VD curve are 1.5, 2.7, 4.0, and 5.7mA, respectively. As a result of the analysis for drain currents after tine lapse, which is based on the simulation for hysteresis loop and the fitting of retention properties of ferroelectric thin films such as PLZT(10/30/70), PLT(10) and PZT(30/70) thin film shows excellent reliability that the decrease of saturation current is about 18% after 10 years.

• Journal of the Korean Electrochemical Society
• /
• v.19 no.2
• /
• pp.39-44
• /
• 2016

Oxygen reduction reaction in the fuel cell (ORR) plays a dominant role in the overall reaction. In addition, the low compatibility between the membrane and the binder consisted of different materials, greatly reduces the efficiency of the fuel cell performance. In view of these two problems, geometrically modified copolymers with 9.9_Bis (4-hydroxyphenyl) were synthesized via condensation reaction instead of conventional biphenol and were adopted as hydrocarbon ionomer binders. By utilizing these binders, two kinds of MEAs using fluorinated Nafion membrane and hydrocarbon based membrane were manufactured in order to electrochemical performance evaluation. With current-voltage curves, there was no significant difference in the 0.6 V when two types of membrane were applied. Also, tafel slope became considerably lower as compared to the Nafion membrane. Thus, it is determined that the new hydrocarbon binder is expected to contribute the improvement in performance of fuel cells.