• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2002.10a
• /
• pp.330-337
• /
• 2002

The HANARO seismic monitoring system is classified as non-nuclear safety(NNS), seismic category I, and quality class T The seismic monitoring system installed at the instrument room consists of five field sensors and one monitoring cabinet. The field sensors are composed of three triaxial accelerometers which installed at base slab, free field and overhead crane support respectively, a seismic trigger and a seismic switch at base slab. The most parts of analog system except field sensors are not produced any more, the improvement of the system is to be needed. The analog system with magnetic tape recorder is not only out-of-date model but dependent upon foreign technology. So it is difficult to get the spare parts and the cost to buy them is increased. Therefore we have improved the analog seismic monitoring system into a new digital seismic monitoring analysis system(SMAS) except five field sensors. After the installation of the new SMAS, we have carried out the site acceptance test(SAT) to confirm the field functions. The results of SAT satisfy the requirements of the fabrication technical specification. This new SMAS is operating at HANARO instrument room to acquire and analyse the signal of earthquake.

• Journal of the Society of Naval Architects of Korea
• /
• v.48 no.2
• /
• pp.171-177
• /
• 2011

Tensile tests were conducted at low temperatures for the steel materials which are used for outer shell of the vessels making transit through the polar regions. The selected steel materials were GL-DH32, GL-DH36 and GL-EH36. In comparison with the results at room temperature, the yield stress increases approximately by 10 to 13 percent at $-30^{\circ}C$ and by 13 to 19 percent at $-50^{\circ}C$ while the tensile strength increases about by 9 percent at $-30^{\circ}C$ and 11 to 14 percent at $-50^{\circ}C$. To obtain true stress-true strain, i.e. correct plastic hardening characteristics, Bridgman's(1952) necking correction formula was introduced taking triaxial state of stresses after onset of diffuse necking into consideration. Photographs of fractured surfaces were taken by using Scanning Electron Microscope immedately after tensile tests completed and one for GL-EH36 has been presented in this paper.

• Journal of Industrial Technology
• /
• v.23 no.A
• /
• pp.119-130
• /
• 2003

This thesis is results of experimental works on the behavior of the cut-and-cover tunnel. Centrifuge model tests were performed to simulate the behavior of the cut-and-cover tunnels having cross sections of national road and subway tunnels. Model experiments were carried out with changing the cut slope and the slope of filling ground surface. Displacements of tunnel lining resulted from artificially accelerated gravitational force up to 40g of covered material used in model tests, were measured during centrifuge model tests. In model tests, Jumunjin Standard Sand with the relative density of 80 % and the zinc plates were used for the covered material and the flexible tunnel lining, respectively. Basic soil property tests were performed to obtain it's the property of Jumumjin Standard Sand Shear strength parameters of Jumunjin Standard Sand were obtained by performing the triaxial compression tests. Direct shear tests were also carried out to find the mechanical properties of the interface between the lining and the covered material. Compared results model tests estimation with respect to displacements of the lining.

• Geotechnical Engineering
• /
• v.4 no.4
• /
• pp.5-18
• /
• 1988

A series of CU triaxial compression tests were conducted to investigate the variation of -untrained shear strength of underconsolidated clay at different degrees of consolidation. The soil samples were artificially made by one-dimensional consolidation using soft Bangkok Clay. The test results showed that the undrained shear strength of clay parabolically increased convoking downward with increasing degrees of consolidation. However, all the measured shear strength were unanimously related to the effective stress. These experimental results were used in the numerical analysis. A finite element computer program was developed to investigate the stability of submarine .slope undergoing rapid deposition taking into account the variation in soil compressibility and permeability during the consolidation process. The relationships of degree of consolidation with time as a function of rate of deposition and angle of slope were established. A method of predicting the time of slope failure and the volume of moving mass of soil was also made.

• Geotechnical Engineering
• /
• v.10 no.3
• /
• pp.17-32
• /
• 1994

To model the anisotropic behavior of soils in the case of reverse loading, an anisotropic hardening description is proposed on the basis of generalized isotropic hardening(GIH) rule. There is a core of the GIH rule in the allowance of the concept that the center of homology of isotropic hardening can be any proper stress states inside a yield surface. The plastic deformations could be represented for the condition of reverse loading, and an explicit constitutive relationship was formulated by utilizing a simple hardening function. The proposed hardening description has been compared with other anisotropic hardening models. For verification three sets of triaxial test results have been predicted for the drained and undrained behavior of overconsolidated clays and Ko consolidated clays.

• Geomechanics and Engineering
• /
• v.2 no.3
• /
• pp.213-227
• /
• 2010

Compacted layers of sand-bentonite mixtures have been proposed and used in a variety of geotechnical projects as engineered barriers for the enhancement of impervious landfill liners, cores of zoned earth dams and radioactive waste repository systems. This paper presents a study on the valorization of local materiel such as dune sand from Laghouat region and mine bentonite intended for the realization of liner base layers in the conception of insulation barriers for hazardous waste centers. In the practice we try to get an economical mixture that satisfies the hydraulic and mechanical properties specified by regulation rules. The effect of the bentonite additions on the mixture is reflected by its capability of clogging the matrix pores upon swelling. In order to get an adequate dune sand-bentonite mixture, an investigation on hydraulic and mechanical behaviours is carried out in this study for different mixtures. Using oedometer test, the adequate bentonite addition to the mixture, which satisfies the conditions on permeability, is found to be around 12% to 15%. These results are also confirmed by direct measurement using triaxial cell.

• Smart Structures and Systems
• /
• v.22 no.4
• /
• pp.459-468
• /
• 2018

In this paper, the effect of non-persistent joints was determined on the behavior of concrete specimens subjected to biaxial loading through numerical modeling using particle flow code in two dimensions (PFC2D). Firstly, a numerical model was calibrated by uniaxial, Brazilian and triaxial experimental results to ensure the conformity of the simulated numerical model's response. Secondly, sixteen rectangular models with dimension of 100 mm by 100 mm were developed. Each model contains two non-persistent joints with lengths of 40 mm and 20 mm, respectively. The angularity of the larger joint changes from $30^{\circ}$ to $90^{\circ}$. In each configuration, the small joint angularity changes from $0^{\circ}$ to $90^{\circ}$ in $30^{\circ}$ increments. All of the models were under confining stress of 1 MPa. By using of the biaxial test configuration, the failure process was visually observed. Discrete element simulations demonstrated that macro shear fractures in models are because of microscopic tensile breakage of a large number of bonded discs. The failure pattern in Rock Bridge is mostly affected by joint overlapping whereas the biaxial strength is closely related to the failure pattern.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.3
• /
• pp.15-22
• /
• 2003

The appropriate description of the stress-anisotropy and time-dependent behavior of cohesive soils is very important in representing the real soil behavior. In this study, two constitutive relations have been incorporated based on the generalized viscous theory: one is the plastic constitutive relation adopted to capture the stress-anisotropy with a few model parameters; the other is the rate-dependent constitutive relation adopted to describe the strain rate-dependent behavior, an important time-dependent behavior in cohesive soils. The incorporated and proposed constitutive model has relatively a few model parameters and their values need not to be re-evaluated at different strain rates. The proposed model has been verified and investigated with the anisotropic triaxial test results obtained by using the artificial homogeneous specimens.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.3
• /
• pp.596-601
• /
• 2009

In this study, the rate-sensitive constitutive model, which was developed in the previous paper of this journal, was validated using the experimental results obtained from the well-calibrated triaxial compression test conducted with the Boston blue clay. The validation was performed for the various cases of the strain rate of 0.05%/hr, 0.5%/hr, 5.0%/hr and OCR of 1, 2, 4, 8. The developed model was validated for the normally and slightly overconsolidated cases; however, the cases of heavily overconsolidation needs further research.

• Computers and Concrete
• /
• v.7 no.2
• /
• pp.191-202
• /
• 2010

A laboratory investigation was conducted to characterize the constitutive property behavior of Cor-Tuf, an ultra-high-performance composite concrete. Mechanical property tests (hydrostatic compression, unconfined compression (UC), triaxial compression (TXC), unconfined direct pull (DP), uniaxial strain, and uniaxial-strain-load/constant-volumetric-strain tests) were performed on specimens prepared from concrete mixtures with and without steel fibers. From the UC and TXC test results, compression failure surfaces were developed for both sets of specimens. Both failure surfaces exhibited a continuous increase in maximum principal stress difference with increasing confining stress. The DP tests results determined the unconfined tensile strengths of the two mixtures. The tensile strength of each mixture was less than the generally assumed tensile strength for conventional strength concrete, which is 10 percent of the unconfined compressive strength. Both concretes behaved similarly, but Cor-Tuf with steel fibers exhibited slightly greater strength with increased confining pressure, and Cor-Tuf without steel fibers displayed slightly greater compressibility.