• 한국전기전자재료학회논문지
• /
• 제30권12호
• /
• pp.768-775
• /
• 2017

Energy harvesting characteristics of trapezoidal piezoelectric cantilever generator, which has a lead zirconate titanate (PZT) laminate film, were compared by longitudinal (3-3) and transverse (3-1) modes. The PZT laminate film, fabricated by a conventional tape casting process, was cofired with Ag electrode at $850^{\circ}C$ for 2 h. A multi-layered Ag electrode by a planar pattern and an interdigitated pattern was applied to the PZT laminate to implement the 3-3 and 3-1 modes, respectively. The energy harvesting performance of the 3-3 mode trapezoidal piezoelectric cantilever generator was better than that of the 3-1 mode. An extremely high output power density of $26.7mW/cm^3$ for the 3-3 mode was obtained at a resonant frequency of 145 Hz under a load resistance of $50{\Omega}$ and acceleration of 1.3 G, which is ~3-times higher than that for the 3-1 mode. Therefore, the 3-3 mode is considered significantly efficient for application to high-performance piezoelectric cantilever generator.

• 한국지반공학회논문집
• /
• 제21권5호
• /
• pp.33-43
• /
• 2005

본 연구는 단부의 경계조건에 따른 매설관의 동적응답을 규명하기 위해 축방향 및 축직각방향에 대해서 자유진동과 강제진동 해석을 수행하였다. 각 경계조건에서의 모드형상을 결정한 후 고유진동수를 구하고, 이들을 이용하여 강제 진동시 발생하는 매설관의 축방향에 대해 변위, 변형률 산정식과 축직각방향에 대한 변위, 휨변형률 산정식을 유도하였다. 또한 가능한 모든 단부 경계조건의 매설관에 대해 최대응력이 발생하는 위치와 크기를 산정하였으며, 매설관의 동적거동에 영향을 가장 많이 발생시킬 수 있는 공진현상을 나타내는 모드수를 예측할 수 있는 식을 제안하였고 관 단부 경계조건이 매설관의 동적응답에 미치는 영향에 대한 규명과 관의 동적응답에 영향을 주는 매개변수들의 영향에 대해 규명하였다.

• Earthquakes and Structures
• /
• 제10권2호
• /
• pp.329-350
• /
• 2016

A parametric study was conducted to investigate the seismic deformation demands in terms of drift ratio, plastic base rotation and compression strain on rectangular wall members in frame-wall systems. The wall index defined as ratio of total wall area to the floor plan area was kept as variable in frame-wall models and its relation with the seismic demand at the base of the wall was investigated. The wall indexes of analyzed models are in the range of 0.2-2%. 4, 8 and 12-story frame-wall models were created. The seismic behavior of frame-wall models were calculated using nonlinear time-history analysis and design spectrum matched ground motion set. Analyses results revealed that the increased wall index led to significant reduction in the top and inter-story displacement demands especially for 4-story models. The calculated average inter-story drift decreased from 1.5% to 0.5% for 4-story models. The average drift ratio in 8- and 12-story models has changed from approximately 1.5% to 0.75%. As the wall index increases, the dispersion in the calculated drifts due to ground motion variability decreased considerably. This is mainly due to increase in the lateral stiffness of models that leads their fundamental period of vibration to fall into zone of the response spectra that has smaller dispersion for scaled ground motion data set. When walls were assessed according to plastic rotation limits defined in ASCE/SEI 41, it was seen that the walls in frame-wall systems with low wall index in the range of 0.2-0.6% could seldom survive the design earthquake without major damage. Concrete compressive strains calculated in all frame-wall structures were much higher than the limit allowed for design, ${\varepsilon}_c$=0.0035, so confinement is required at the boundaries. For rectangular walls above the wall index value of 1.0% nearly all walls assure at least life safety (LS) performance criteria. It is proposed that in the design of dual systems where frames and walls are connected by link and transverse beams, the minimum value of wall index should be greater than 0.6%, in order to prevent excessive damage to wall members.

• 대한기계학회논문집
• /
• 제16권7호
• /
• pp.1244-1254
• /
• 1992

본 연구에서는 탄성, 점탄성 및 탄성박판으로 이루어진 복합적층구조물의 진 동특성을 해석함에 있어서 모재 및 구속재의 길이방향변위, 회전관성 그리고 전단변형 의 영향과 접착제의 법선 및 전단변형의 영향을 고려한 계의 운동방정식을 연립 1계 미분방정식의 형태로 유도하고 수치계산 결과를 실험과 비교하였다. 그리고 구속재 와 접착제의 두께변화에 따라서 접착제의 법선 및 전단변형이 계의 감쇠특성에 미치는 영향을 고찰하였다.

• 한국해안·해양공학회논문집
• /
• 제27권1호
• /
• pp.1-8
• /
• 2015

우리나라 남서해안은 풍력발전에 최적지로 평가받고 있으며 최근 해상풍력 구조물을 포함하는 해안구조물의 건설이 증가하고 있다. 그러나 우리나라 남서해안의 조차는 3~8 m까지 발생하여 남서해안에 설치되는 풍력기초들은 횡방향력과 조류의 다방향 흐름에 의한 세굴로 전체 구조물에 예상치 못한 진동에 의한 불안정성이 야기될 수 있다. 이 연구에서는 회전식 수리저항성능 실험기를 이용하여 인공지반시료의 수리저항성능을 평가하였으며 전기비저항 측정결과와 비교하여 수리저항성능과 전기비저항 특성과의 상관관계에 대한 연구를 진행하였다. 실험결과 일방향 한계전단응력과 양방향 한계전단응력을 상한계와 하한계로 표시하고 전기비저항 특성과 상관관계를 도시하면 조립토와 세립토가 비교적 명확히 구분되고 한계전단응력과의 상관관계 도출이 가능한 것으로 나타났다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.37-38
• /
• 2006

본 연구에서는 압전체의 횡 진동모드를 이용한 압전 초음파 진동자를 설계 분석하였다. 이전의 란쥬반 진동자는 진동을 얻기 위하여, 복수의 원판 또는 사각판 형태의 압전 세라믹을 서로 반대 방향으로 분극하여 마주 보도록 설치한 후 전기적으로 병렬로 연결하고 상단 및 하단에 금속부을 부착하여 전체를 볼트로 조인 복잡한 구조와 큰 출력 파워를 갚는 반면, 본 연구에서는 판상형의 압전소자와 일체형 금속진동체를 이용하여 기계적 출력 파워 조절이 용이한 구조의 압전 진동자를 고안하여, 압전진동자의 횡 진동 모드를 이용함으로써 신뢰성과 정확도가 높고 진동효율이 최대가 되도록 설계하였다. 설계 개발된 압전 진동자는 진동의 크기 조절이 용이하여 일반 진동자 뿐 만 아니라, 외과 및 안과 수술에 있어서 인체조직이나 각막상피의 활성화를 유지한 상태에서 안전하게 절개 및 분리 시술용 진동자로 사용 할 수 있는 이점이있다. 압전 진동자는 유한요소법 시뮬레이션 프로그램 (ATILA 5.2.4)을 이용하여 설계를 하였으며 압전소자의 두께는 각각 0.2 mm, 0.5 mm로 제작하여 시뮬레이션 결과와 제작된 샘플의 특성을 비교하였고, 변위측정은 칼날을 결합 한 상태에서 공진 주파수대역 부근 주파수별로 측정 비교하였다.

• 한국전산구조공학회논문집
• /
• 제19권2호
• /
• pp.151-160
• /
• 2006

본 연구에서는 균일단면 뿐만 아니라 불균일 단면을 갖는 곡선보의 동적해석을 효과적으로 수행할 수 있는 새로운 2절점 곡선보 요소를 제안하였다. 전단변형률을 고려한 본 요소는 Hellinger-Reissner 변분이론에 바탕하여 유한요소정식화를 수행하였다. 또한, 변위장에 대해 무절점 자유도를 추가적으로 도입하여 요소의 수치적 성능을 크게 향상시켰다. 계산의 효율성을 위해, 요소정식화의 최종단계에서 정치조건으로부터 응력매개변수들을 제거하고, 동적축약을 통하여 무절점 자유도 성분들 또한 최종적인 유한요소방정식에서 제거되어 일반적인 변위기저 요소와 같은 자유도를 가지는 유한요소방정식을 얻을 수 있다. 몇 가지 수치예제들에 대한 해석을 통하여, 무절점 자유도와 변위장에 일치하는 적절한 응력매개변수가 혼합요소의 수치적 거동에 미치는 영향을 분석하였으며, 본 연구에서 제안된 2절점 혼합요소가 곡선보의 동적해석에서 매우 정확하고 효율적임을 확인할 수 있었다.

• Wind and Structures
• /
• 제23권2호
• /
• pp.143-155
• /
• 2016

The interaction between two different shaped structures is very important to be understood. Fluid-structure interactions and aerodynamics of a circular cylinder in the wake of a V-shaped cylinder are examined experimentally, including forces, shedding frequencies, lock-in process, etc., with the V-shaped cylinder width d varying from d/D = 0.6 to 2, where D is the circular cylinder diameter. While the streamwise separation between the circular cylinder and V-shaped cylinder was 10D fixed, the transverse distance T between them was varied from T/D = 0 to 1.5. While fluid force and shedding frequency of the circular cylinder were measured using a load cell installed in the circular cylinder, measurement of shedding frequency of the V-shaped cylinder was done by a hotwire. The major findings are: (i) a larger d begets a larger velocity deficit in the wake; (ii) with increase in d/D, the lock-in between the shedding from the two cylinders is centered at d/D = 1.1, occurring at $d/D{\approx}0.95-1.35$ depending on T/D; (iii) at a given T/D, when d/D is increased, the fluctuating lift grows and reaches a maximum before decaying; the d/D corresponding to the maximum fluctuating lift is dependent on T/D, and the relationship between them is linear, expressed as $d/D=1.2+{\frac{1}{e}}T/D$; that is, a larger d/D corresponds to a greater T/D for the maximum fluctuating lift.

• Structural Engineering and Mechanics
• /
• 제61권4호
• /
• pp.527-538
• /
• 2017

The evaluation of the loss-of-support conditions of frictional beam-to-column connections using simplified numerical models describing the transverse response of a portal-like structure is presented in this paper considering the effects of the seismic-hazard disaggregation. Real earthquake time histories selected from European Strong-motion Database (ESD) are used to show the effects of the seismic-hazard disaggregation on the beam loss-of-support conditions. Seismic events are classified according to different values of magnitudes, epicentral distances and soil conditions (stiff or soft soil) highlighting the importance of considering the characteristics of the seismic input in the assessment of the loss-of-support conditions of frictional beam-to-column connections. A rigid and an elastic model of a frame of a precast industrial building (2-DoF portal-like model) are presented and adopted to find the minimum required friction coefficient to avoid sliding. Then, the mean value of the minimum required friction coefficient with an epicentral distance bin of 10 km is calculated and fitted with a linear function depending on the logarithm of the epicentral distance. A complete parametric analysis varying the horizontal and vertical period of vibration of the structure is performed. Results show that the loss-of-support condition is strongly influenced by magnitude, epicentral distance and soil conditions determining the frequency content of the earthquake time histories and the correlation between the maxima of the horizontal and vertical components. Moreover, as expected, dynamic characteristics of the structure have also a strong influence. Finally, the effect of the column nonlinear behavior (i.e. formation of plastic hinges at the base) is analyzed showing that the connection and the column are a series system where the maximum force is limited by the element having the minimum strength. Two different longitudinal reinforcement ratios are analyzed demonstrating that the column strength variation changes the system response.

• 한국자동차공학회논문집
• /
• 제22권3호
• /
• pp.33-41
• /
• 2014

Fretting is a kind of surface degradation mechanism observed in mechanical components and structures. When two pieces of materials, pressed together by an external static load, are subjected to a transverse cyclic loading or various vibrations, so that one contacting face is relatively displaced cyclically parallel to the other face, wear of the mating surfaces occurs. These fretting damages may be observed in electrical connectors for automotive components, where there are special environments and various vibration conditions. This study aims to evaluate the usefulness of fretting test equipment that was developed for reliability test of electrical connector. Fretting tests were carried out using tin coated connectors and friction force, contact resistance, contact area and roughness of contact region were investigated. The following results that will be helpful to understand the fretting wear mechanism, increase process the contact resistance and contact area were obtained. (1) In the same frequency and slip amplitude, the friction force, roughness and contact area increased rapidly until about $10^3$ cycles, after which it was slightly changed. (2) In the various frequency and slip amplitude, the contact area increased with slip amplitude and cyclic numbers, but it did not depend on cyclic frequency. (3) The surface roughness of contact region did not depend on the cyclic frequency. From these results, the applicability of the fretting wear test equipment and reliability of connector were discussed.