• 한국표면공학회지
• /
• 제42권3호
• /
• pp.128-132
• /
• 2009

Transparent conducting thin films of indium tin oxide(ITO) co-sputtered with aluminum-doped zinc oxide(AZO) were deposited on glass substrate by dual magnetron sputtering. It was found that the electrical properties and structural characteristics of the films are significantly changed according to the sputtering power of the AZO target. The IAZTO film prepared with D.C power of ITO at 100 W and R.F power of AZO at 50 W shows an electrical resistivity of $4.6{\times}10^{-4}{\Omega}{\cdot}cm$ and a sheet resistance of $30{\Omega}/{\square}$ (for 150 nm thick). Besides of the improvement of the electrical properties, compared to the ITO films deposited at the same process conditions, the IAZTO films have very smooth surface, which is due to the amorphous nature of the films. However, the electrical conductivity of the IAZTO films was found to be deteriorated along with the crystallization in case of the high temperature deposition (above $310^{\circ}C$). In this work, high quality amorphous transparent conductive oxide layers could be obtained by mixing AZO with ITO, indicating possible use of IAZTO films as the transparent electrodes in OLED and flexible display devices.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2008년도 추계학술발표대회 및 제15회 신소재 심포지엄
• /
• pp.33.2-33.2
• /
• 2008

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.209-209
• /
• 2012

High-efficient transparent conductive oxide (TCO) film-embedding Si heterojunction solar cells were fabricated. An additional doping was not applied for heterojunction solar cells due to the spontaneous junction formation between TCO films and an n-type Si substrate. Three different TCO coatings were formed by sputtering method for an Al-doped ZnO (AZO) film, an indium-tin-oxide (ITO) film and double stacks of ITO/AZO films. An improved crystalline ITO film was grown on an AZO template upon hetero-epitaxial growth. This double TCO films-embedding Si heterojunction solar cell provided significantly enhanced efficiency of 9.23% as compared to the single TCO/Si devices. The effective arrangement of TCO films (ITO/AZO) provides benefits of a lower front contact resistance and a smaller band offset to Si leading enhanced photovoltaic performances. This demonstrates a potential scheme of the effective TCO film-embedding heterojunction Si solar cells.

• 한국전기전자재료학회논문지
• /
• 제20권12호
• /
• pp.1044-1048
• /
• 2007

With development of electronic products the demands for miniaturization and weight-lightening have increased until a recent date. Accordingly, The effort to substitute glass substrates was widely made. However, polymer substrates have weak point that substrates were damaged at high temperature. In this paper, we deposited transparent conductive film at low temperature. And we inserted Au thin film between oxide to compensate for deteriorated electrical characteristics. Ga-doped ZnO(GZO) multilayer coatings were deposited on glass substrate by DC sputtering. The optimization of deposition conditions of both AZO and Au layers were performed to obtain better electrical and optical characteristics in advance. We presumed that the properties of multilayer were affected by the deposition process of both GZO and Au layers. The best multilayer coating exhibited the resistivity of $2.72{\times}10^{-3}\;{\Omega}-cm$ and transmittance of 77 %. From these results, we can confirm a possibility of the application as transparent conductive electrodes.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 C
• /
• pp.1553-1555
• /
• 2003

Coatings on glass with highly transparent conducting oxide films(TCOs) are performed mostly by using indium tin oxide(ITO). This Oxide material is very common for applications where both high electrical conductivity. Photovoltaic cells, transparent electrical heater, selective optical filter, and a optical transmittance are essential. In this study, ITO thin films were deposited on $SiO_2$/soda-line glass plates by a dc magnetron sputtering technique. The crystallinity and electrical properties of the films were investigated by X-ray diffraction(XRD), atomic force microscopy(AFM) scanning and 4-point probe. The optical transmittance of ITO films in the range of 300-800nm were measured with a spectrophotometer. As a result, we obtained polycrystalline structured ITO films with (222), (400), and (440) peak. Transmittance of all the films were higher than 90% in the visible range.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.255-255
• /
• 2011

Zinc oxide based thin films have been extensively studied in recent several years because they have very interesting properties and zinc oxide is non-poisonous, abundant and cheap material. ZnO films are employed in different applications like transparent conductive layers in solar cells, protective coatings and so on. Wide industrial application of the ZnO films requires of development of cheap, effective and scalable technology. Typically used technologies don't completely satisfy the industrial requirements. In the present work, we studied effect of the deposition parameters on the structure and properties of ZnO films deposited by DC arc plasmatron. The varied parameters were gas flow rates, precursor composition, substrate temperature and post-deposition annealing temperature. Vapor of Zinc acetylacetone was used as source materials, oxygen was used as working gas and argon was used as the cathode protective gas and a transport gas for the vapor. The plasmatron power was varied in the range of 700-1500 watts. Flow rate of the gases and substrate temperature rate were varied in the wide range to optimize the properties of the deposited coatings. After deposition films were annealed in the hydrogen atmosphere in the wide range of temperatures. Structure of coatings was investigated using XRD and SEM. Chemical composition was analyzed using x-ray photoelectron spectroscopy. Sheet conductivity was measured by 4-point probe method. Optical properties of the transparent ZnO-based coatings were studied by the spectroscopy. It was shown that deposition by a DC Arc plasmatron can be used for low-cost production of zinc oxide films with good optical and electrical properties. Increasing of the oxygen content in the gas mixture during deposition allow to obtain high-resistive protective and insulation coatings with high adhesion to the metallic surface.

• 접착 및 계면
• /
• 제3권3호
• /
• pp.22-29
• /
• 2002

하층에 유 무기 전도성 물질을 코팅하고 상층은 다관능성 아크릴레이트를 코팅한 다층코팅의 자외선 경화형 시스템을 도입하였다. 이러한 다층코팅은 투명한 PMMA, PC, PET 등의 기재 위에 wet and wet 방식의 코팅 방법을 사용하여 제조하였다. 도막의 표면저항과 물성은 상층 두께의 변화와 상대 습도를 다르게 하여 측정하였다. 상층두께가 $10{\mu}m$ 이하일 때 $10^8{\sim}10^{10}{\Omega}/cm^2$의 표면저항을 나타냈으며 표면 물성은 단층코팅에 비해서 다층코팅이 더 우수하게 나타났다. 그리고 다층코팅에서의 도판트 이동효과는 접촉각과 FT-IR/ATR을 통해 관찰하였다. 하층이 무기 전도성 물질인 경우에는 관찰되지 않는 도판트(DBSA)의 필름-기재 계면에서 필름-공기 계면 쪽으로 이행되는 거동이 유기전도성 물질인 경우에는 관찰되었다.

• 한국표면공학회지
• /
• 제55권6호
• /
• pp.353-362
• /
• 2022

Recently, transmittance of photomasks for ultra-violet (UV) region is getting more important, as the light source wavelength of an exposure process is shortened due to the demand for technologies about high integration and miniaturization of devices. Meanwhile, such problems can occur as damages or the reduction of yield of photomask as electrostatic damage (ESD) occurs in the weak parts due to the accumulation of static electricity and the electric charge on chromium metal layers which are light shielding layers, caused by the repeated contacts and the peeling off between the photomask and the substrate during the exposure process. Accordingly, there have been studies to improve transmittance and antistatic performance through various functional coatings on the photomask surface. In the present study, we manufactured antireflection films of Nb₂O₅, | SiO₂ structure and antistatic films of ITO designed on 100 × 100 × 3 mmt sodalime glass by DC magnetron sputtering system so that photomask can maintain high transmittance at I-line (365 nm). ITO thin film deposited using In/Sn (10 wt.%) on sodalime glass was optimized to be 10 nm-thick, 3.0 × 103 𝛺/☐ sheet resistance, and about 80% transmittance, which was relatively low transmittance because of the absorption properties of ITO thin film. High average transmittance of 91.45% was obtained from a double side antireflection and antistatic thin films structure of Nb₂O₅ 64 nm | SiO₂ 41 nm | sodalime glass | ITO 10 nm | Nb₂O₅ 64 nm | SiO₂ 41 nm.

• 한국표면공학회지
• /
• 제50권2호
• /
• pp.55-71
• /
• 2017

Transparent Conductive Oxide (TCO), especially Indium Tin Oxide (ITO) films are almost prepared by DC magnetron sputtering because of the advantage of obtaining homogeneous large area coatings with high reproducibility. The purpose of this report is describe a detailed investigation of key factors dominating electrical and structural properties of sputtered ITO films. It was confirmed that crystallinity and electrical properties of ITO films were strongly depend on the sputtering pressure and kinetic energy of sputtered particles which are expected to have a close relation with the transport processes between target and substrate. And also, nodule formation on the ITO target was suppressed by both $CaCO_3$ addition and decreasing micro-pore in the target. On the other hand, we focused on the characteristics of amorphous TCO film to use as transparent electrode for various applications. To realize high thermoelectric performance, it was tried to control both high electrical conductivity and low thermal conductivity for the amorphous IZO:Sn films.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.313-314
• /
• 2007

Ga-doped ZnO(GZO) multilayer coatings were prepared on glass by DC sputtering. Optimization of the deposition conditions of both AZO and Au layers were performed for better electrical and optical characteristics. The properties of multilayer were affected by the deposition process of both GZO and Au layers. The best multilayer coating exhibits low resistivity of $2.72{\times}10^{-3}\;{\Omega}-cm$ and transmittance of 77%. From these results, we can confirm a possibility of the application as transparent conductive electrodes.