• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.706_707
• /
• 2009

This paper presents the torque calculation method of a permanent magnet spherical motor. To calculate the torque of the spherical motor by using finite element method (FEM), 3-dimensional FEM must be used. However since it spends too much time and memory in using 3-D FEM, the easier torque calculation method was presented. In this method, it is very important to get the approximation function of the torque profile curve; the authors present the approximation method of the torque profile curve. This paper shows the torque calculation result coming closer to the torque by 3-D FEM.

• Journal of Electrical Engineering and Technology
• /
• 제5권3호
• /
• pp.431-434
• /
• 2010

This paper presents the torque calculation method of a permanent magnet spherical motor. To calculate using the finite element method (FEM), three-dimensional (3D) FEM must be used. However, since the method requires excessive time and memory, an easier torque calculation method is hereby presented. In the proposed method, it is very important to obtain the approximation function of the torque profile curve. We present the approximation method of the torque profile curve and show that the torque calculation result can approximate the torque obtained by 3-D FEM.

• 전기학회논문지
• /
• 제66권7호
• /
• pp.1047-1052
• /
• 2017

In this paper, the calculation torque using the d-q axis has advantage like faster execution time. However, the torque ripple can't be considered in the torque calculation using d-q axis equivalent circuit because the time-dependent component is removed. When d-q transformation was performed, it was founded that some parameters has some characteristics. These characteristics were considered for representing torque ripple. The calculation with d-q axis transformation and Finite Element Analysis(FEA) were performed, and the results were compared. As a result, it was validated that the calculated torque can be expressed with ripple.

• 전기학회논문지
• /
• 제62권2호
• /
• pp.171-176
• /
• 2013

Classically, reluctance torque of IPMSM(Interior Permanent Magnet Synchronous Motor) by using inductance according to current phase angle generates an error. This error is affected by total torque. From current phase angle $0^{\circ}$ to large errors will occur, because reluctance torque include current phase angle. But, reluctance torque from steady-state voltage equation of IPMSM is represented by linkage flux. So, reluctance torque is unrelated to the current phase angle formula can be derived. In this paper, operating torque was analyzed by d, q-axis linkage flux of IPMSM and reluctance torque to perform calculations reduced the error of the total torque calculation.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제2권2호
• /
• pp.159-164
• /
• 2013

Difficulty of torque measurements in high-speed permanent magnet (HSPM) motors has necessitated the development of improved torque calculations. Hence, this paper presents an analytical torque calculation of a high speed permanent magnet (HSPM) motor based on the power factor angle. On the basis of analytical magnetic field solutions, the equations for circuit parameters such as back-emf and synchronous inductance are derived analytically. All analytical results are validated extensively by non-linear finite element (FE) calculations and measurements. The internal angle (${\delta}$) between the back-emf and the phase current is calculated according to the rotor speed by using analytical circuit parameters and the measured power factor because this angle is not measured but estimated in case of sensorless drive of the HSPM motor, significantly affecting torque calculation. Finally, the validity of the torque analysis method proposed in this paper is confirmed, by showing that the torque calculated on the basis of the internal angle is in better agreement with the measurements.

• Journal of Electrical Engineering and Technology
• /
• 제13권3호
• /
• pp.1223-1231
• /
• 2018

The direct torque control (DTC) scheme features a simple structure thanks to stator flux-oriented control. It has the advantage of robustness against motor parameters variation since only the stator resistance is involved in the control scheme. On the other hand, the disadvantage of DTC is large torque ripple. To reduce the torque ripple, many studies on DTC-space vector modulation (DTC-SVM) schemes, which modulate the duty ratio with a fixed switching cycle, have been proposed. However, there is the difficulty in obtaining the duty ratio for DTC-SVM. Hence, this paper proposes a new duty ratio selection and stator flux calculation methods for reducing torque ripple. Simulations and experiments were carried out to determine the validity of the proposed method. The proposed scheme has simplified the duty ratio command and achieved the same control performance as the conventional duty ratio modulation method without using the information of motor parameters.

• 한국자동차공학회논문집
• /
• 제21권4호
• /
• pp.188-194
• /
• 2013

Hydrostatic pumps and motors occupy an important position in hydraulic system. There are a lot of researches on characteristics of hydraulic pumps, but not hydraulic motors. So in order to know the characteristics of hydraulic motors we had this research. The purpose of this study is to derive and analyze the theoretical calculation of hydraulic axial piston motor torque and torque ripples. Then, analyzed the differences between torque ripples with dead place and without dead place on the valve plate, and modeling a hydraulic motor with AMESim software. Finally, theoretical calculation of hydraulic motor torque ripples was verified from the viewpoint of simulation.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 A
• /
• pp.475-478
• /
• 1994

In this paper two methods of torque control for brushless DC motor with non-ideal trapezoidal back EMF are presented. One is the method of modulating the reference current so as to give a constant torque since the torque is given by the back EMF and the. phase currents. And the current control loop includes the feedforward control of back EMF and of the neutral voltage between the neutral points of the inverter and of the machine. The other is a direct voltage calculation algorithm for a given reference torque. In the two methods, the time delay due to the calculation is compensated by one sampling current prediction. The simulation results are presented to verify the proposed methods.

• 대한기계학회논문집B
• /
• 제22권3호
• /
• pp.326-335
• /
• 1998

In this study, a steady three-dimensional incompressible turbulent flow within a torque converter was numerically analyzed with the introduction of interrow mixing model. Mixing planes were introduced to exchange the flow informations between two adjacent elements of the torque converter. The mixing planes were installed among three elements of the torque converter. Therefore, in the present method, it could be possible to calculate the flow-filed within the torque converter without any assumption of circulating flow rates or any extension of boundaries toward the upstream and the downstream for each element. The numerically calculated performances of the torque converter were in good agreement with experimental results, and the complex flow patterns were be observed according to design and off-design condition. As a conclusion, it was found that the present numerical method was very effective in the steady flow analysis of torque converters.

• 동력기계공학회지
• /
• 제13권3호
• /
• pp.40-46
• /
• 2009

This study on the bolt elongation and torque measuring method by ultrasonic nod-destructive method. In the past, The dial gage was used for the elongation measurement of gas turbine bolts. The purpose of this study is to improve the traditional bolt elongation measurement method. The old method using dial gage measures the elongation of the gas turbine bolt. If the length differences among the loading bolts are within the required range, The loading torques of bolts consider as acceptable. But this method can not give the information about torque differences among the loading bolts. It could bring out vibration of turbine due to loading torque differences among the bolts. So the elongation and torque must be measured simultaneously. The new technology using ultrasonic non-destructive method can give the information about bolt elongation and torque. The ultrasonic method basically measures the speed in the bolt material for the calculation the bolt elongation. But the ultrasonic speed varies according to temperature and loading torque of bolts. So the factors of temperature and loading power were investigated and reflected to the calculation of bolt elongation and torque. The results of this study shows the big difference among the bolts torque in the old method and the torque differences among the bolts can be adjusted by reflecting the result of this study. And this torque adjusting method can decrease gas turbine vibration problem due to torque difference among the bolts. So this paper shows ultrasonic method is better than old method for the measurement of bolt elongation and torque.